-Determine the elongation of the steel bar 1m long and 1.5 cm cross-sectional area when subjected to a pull of 1500 kg. Take E=2*10 kg/cm ?

Q: Let's consider a rod subjected to the shown axial forces. If we consider a linear elastic behavior,…

A:

Q: A bar BD is held in a horizontal position when there is no load by the steel wire AB. When a weight…

A: The cross sectional area of wire is The modulus of elasticity is The yield strength is The…

Q: The lap joint illustrated is fastened with 4 rivets, each with 3/4-in. diameter. Find the max load P…

A:

Q: Determine of the internal resistance force of each segment of the bar shown below, and the total…

A: Find the total elongation and force in each segment.

Q: Let's consider a rod subjected to the shown axial forces. If we consider a linear elastic behavior,…

A:

Q: The rigid bar ABC supports a load of 21.1 kN at point C. A circular rod (diameter 25 mm) supports…

A: Given:

Q: Bar (1) has a cross-sectional area of 0.75 in.2. If the stress in bar (1) must be limited to 48 ksi,…

A: Given:A1=0.75 in2σallow=48 ksi

Q: A composite rod of overall length of 200 mm comprised of a steel rod and brass rod attached rigidly…

A: Stress is the ratio of force to the area of the material. It is denoted by the σ & measured in…

Q: The bar ABC is supported by a pin at A and a steel wire at B. Determine the magnitudeof force…

A:

Q: Q1

A:

Q: A round Steel rod of 50 mm diameter is bent into an arc of radius 10m. What is the maximum stress in…

A:

Q: The rigid bar ABCD supports point loads at A and D and is being supported by two bars at B and C.…

A: Given data: F1=120 kNF2=90 kN Need to determine the absolute value of the deformation at point C.

Q: 4) The bar shown has a cross-sectional are of A and a modulus of elasticity of E. If the axial force…

A:

Q: The rod made of two different materials is fixed at point A. AB aluminum, BC steel It is made of…

A: Given data: The modulus of elasticity in aluminum bar is E1=70 GPa=70×103 MPa The modulus of…

Q: The force on a wagon wheel is F=2000 N. Find the axle diameter of the wagon wheel made of Fe50…

A: To design a machine element, we need to analyze the forces applied to the element. The forces can…

Q: Rod ABC has a diameter of 30 mm at AB and diameter of 20 mm at BC. the whole rod is subjected to a…

A:

Q: Determine the maximum stress in the frame of the 100kN punch press as shown in the figure. 15cm 36cm…

A: Maximum stress will be at the centre of the section X-X shown below. We convert all dimensions into…

Q: Calculate the displacement of B-D-F points using the energy method or the Castigliano method. Cross…

A:

Q: rmine the support reaction at D pade of solid cvlindors: ARİS S

A:

Q: Determine the total elongation or deformation in the steel bar. Given: P1= 5kN P2=27kN P3=32kN P3 A…

A:

Q: the contraction of the bar

A: Given ; A steel bar of;     ⇒   40mm2×40mm2cross-section is subjected to an axial compressive load,…

Q: Find the elongation of wires AC and AB if the length of the wire is 106 mm and 151 mm respectively.…

A: Given: Length of wire AC→LAC=106 mm Length of wire AB→LAB=151 mm Cross sectional area of both the…

Q: The joint is subjected to the force system shown in the figure below (Figure 1) where P₁ = 270 lb…

A: given data  P1 = 270 lb P2 = 480 lb find the combined normal stress at point B.

Q: A 5-kN tensile load is applied to a test coupon made from 1.6-mm flat steel plate (E = 200 GPa, v =…

A:

Q: A steel rod is subjected to a gradually applied load (F) which gave a rise to a maximum stress of…

A:

Q: Question 1: A steel rod is rigidly attached between an aluminum rod and a bronze rod as shown .…

A: Given   Area of steel, A = 400 mm2     Stress at steel = 140 MPa Find   Maximum load, P

Q: is it okay to solve this even if it is not in equilibrium? Why?

A: Solution:

Q: Determine of the internal resistance force of each segment of the bar shown below. and the total…

A: Find the force in bar and total elongation.

Q: Bar (1) has a cross-sectional area of 0.75 in.2. If the stress in bar (1) must be limited to 49 ksi,…

A: Correct answer: (iv) 22.05 kips

Q: A 3-mm thick plastic hollow 2-1 cylinder (E-3 GPa) and a rigid circular plate are used to support a…

A:

Q: 1. The 30.0-mm-diameter steel rod whose E = 150.0 GPa is subjected to the axial forces shown in the…

A:

Q: block is 4 inches long in the x direction, 2 inches long in the y direction, and 3 inches long in…

A:

Axial Load

When a bar of the uniform cross-section is acted by a load, such that the load acts along the longitudinal axis of the bar, such kinds of loadings are known as axial loadings. In general terms, a load is an external force acting on a component. An axial load acts perpendicular to the geometric cross-section of the component. Based on the direction of the application of the load, an axial load can be tensile or compressive. The analysis of bodies under the action of axial loads is generally studied under the branch of mechanics, known as statics.