books' answers are second picture 12-41. Determine the displacement at x = 7 m and theslope at A. El is constant.X4 m3 kN/m-3 m50 kN3 m-B 12-41dvdx0₁Vv|x=71ΕΙ1=7 m12.3x²0.5.x³ + 0.5< x-4 >³ -25 < x-7>² kN·m²,-278.7279kN · m²ΕΙ4.10x³0.125x4 +0.125x4>4 -8.33 < x-7>³ kNm³,22 JANEI-278.7x835kN - m³EI

The flexural rigidity is constant.

Answered: Determine the displacement at x = 7 m…

Engineering

Mechanical Engineering

Determine the displacement at x = 7 m and the slope at A. El is constant. 4 m 3 kN/m 3 m 50 kN 3 m NB

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Related questions

Q: a helical compression spring with squared and ground ends is ti be made of a steel wire 79 gpa and…

A: The objective of the question is to determine the spring constant 'k' for a helical compression…

Q: A 5kg collar is suspended by a spring at rest a Point A, as shown. The unstretched lenght of the…

A: The collar is rest at point A.The unstrecthed lengthof collar is The mass of collar is The collar is…

Q: Consider the gas-phase reaction for the synthesis of methanol from CO and O₂: CO + 2H₂ CH3OH. The…

A: Gas phase reaction of methanol :Kp at 500K =

Q: Design a double-dwell cam to move a follower from 0 to 2.5 in in 60 deg, dwell for 120 deg, fall 2.5…

A: Given:RiseDwellFallDwellTo find:Design the double dwell cam.

Q: A 1.86-m³ rigid tank contains steam at 220°C. One-third of the volume is in the liquid phase and the…

A: Given:The volume of the rigid tank is the temperature of steam is The volume of the liquid phase is…

Q: The momentum equations for a rotating shallow homogeneous fluid with a free upper surface (i.e. the…

Q: . What is the friction

A: Given datathe length of the pipe L = 1200ftthe diameter of the pipe d =6 in = 0.5 ftthe volumetric…

Q: Liquid water at 15 C flows out of a nozzle straight up 15 m. What is nozzle Vexit?

A: Liquid water at 15 °C flows out of a nozzle straight up, h = 15 m. What is nozzle Vexit?

Q: A concentric shaft AB made of hollow bronze (OD = 100 mm, ID = 80 mm, G = 41 GPa) and solid steel (D…

A: Given:To find:Determine the maximum permissible torque T.

Q: Water flowing in a pipe with a velocity of 28 m/s and a static gage pressure of 970 kPa is split…

A: The inlet pressure is The inlet velocity is

Q: (,),= 0.2 and (,), = 0.55. At the instant shown, a counter-clockwise moment T B. You are required…

A: Given:To find:

Q: 23000064940 *} } [ < € ] {* } + [ ^** + m₂ + m₂ m₂ m₂ m₁ =1kg m₂ = 2kg k₁ = k₁= k₂ = 1¾ 2₁ Determine…

A: Also,

Q: 8.7 Diffuser A jet flies at an altitude of 10 km, where the pressure is 0.32 bar, and the…

A: The altitude is .The pressure is The temperature is .The inlet velocity is The inlet area is The…

Q: Find the horizontal and vertical forces to hold stationary the nozzle shown in the figure below. The…

Q: a water spider of mass m is resting on the surface of the water. Assuming that each leg supports…

Q: (Q3) sk) - A 5mx7m wall consists of 3 glass windows of 1.5mx1.5m dimensions. The wall has thickness…

A: Given,A wall of 5m*7m consist of 3 windows of 1.5m*1.5m.Thickness of wall = 0.125 mThermal…

Q: Q1. A ductile hot-rolled steel bar has a minimum yield strength in tension and compression of 350…

A: “Since you have posted a question with multiple sub-parts, we will provide the solution only to the…

Q: A natural-draft cooling tower is to remove 70 MW of waste heat from the cooling water that enters…

A: The heat removed is The inlet temperature of water is The exit temperature of water is The dry bulb…

Q: A friction sample is placed on a test ramp that pivots about Point O. When the end of the ramp is…

A: The value of height (h)=1.2 ftThe value of length (L)=3.5 ftDetermine the coefficient of friction…

Q: A disk with radius R and mass m begins from rest and then moves without slipping while being pulled…

A: In the above diagram, N is normal force, m is mass, g is gravitational acceleration, P is applied…

Q: The 3.22-1b particle A slides on the smooth horizontal plane and is connected to the spring by a…

Q: nd the diameter and the number of teeth on both gears. plution:

A: Given data:Velocity ratio (VR)=5:1Centre distance (C) = 12inPitch (Pd) = 10

Q: If I am given two thermodynamic properties of a material as equations with some units that are…

A: To Find:the units of unknown thermodynamic properties.Given:the given properties are pressure and…

Q: 9-34. Locate the center of gravity of the homogeneous cantilever beam and determine the reactions at…

A: The weight density of material is

Q: A cylindrical specimen of some metal alloy having an elastic modulus of 123 GPa and an original…

A: A cylindrical specimen given Load P=2170NG=123GPad= 3.5mmAllowable elongation = 0.46mm

Q: For the state of stress shown, determine the value of Txy for which the maximum shearing stress is…

Q: Please click on the point in the heating curve where the vapor pressure is equal to the external…

A: When vapor pressure becomes equal to external pressure, bubble formation takes place inside the…

Q: A triple threaded worm has a pitch diameter of 6 in. The hob for cutting the worm wheel has a…

Q: nout slipping under ing constant k, is un G after the center

A: The number of revolutions is obtained as follows-

Q: Consider steady flow in the closed cavity shown in the figure. The bottom and side walls are fixed,…

A: The problem you’re describing is a classic fluid dynamics problem known as Couette flow, which is a…

Q: The sketch below shows a material with a crack of length 2a, and a nominal stress of so. You are…

A: Given Data:To Find:

Q: The boiler of a power steam cycle operates at 6000 kPa and the condenser at 50 kPa. At the entrance…

A: “Since you have posted a question with multiple sub parts, we will provide the solution only to the…

Q: B. Determine the force developed in members FE, EB, and BC of the truss and state if these members…

A: Determine the force developed in members FE, EB, and BC of the truss and state if these members are…

Q: 1. A mass weighing 32 lb stretches a spring by 2 ft. The mass is released from rest at the…

A: This problem is related to the equation of motion of a body under the action of constant force. It…

Q: AP10.1 A three-axis pick-and-place application requires the precise movement of a robotic arm in…

Q: Refrigerant-134a at 1.4 MPa and 90°C is throttled to a pressure of 0.6 MPa. The temperature of the…

A: Throttling is a process in which the fluid is allowed to pass through a restricted passage and…

Q: Explain the production process of fibreglass pre-preg

A: Selection of MaterialsFiber TreatmentResin FormulationImpregnationPartial Curing (B-Stage)Cutting…

Q: The internal loadings at a section of the beam consist of an axial force of F = 380 N, a shear force…

A: Given data:The internal loadings at a section of the beam consist ofan axial force of ,a shear force…

Q: Required information Two kilograms of saturated water vapor at 600 kPa are contained in a…

A: Mass, m=2 kg.The initial pressure is P1= 600 KPa.The pressure at expansion is P2= 150…

Q: Please explain and show examples of chemical vapour deposition

A: Chemical Vapor Deposition (CVD) is a process used to produce thin films, coatings, or other…

Q: Type BJ: A 5 kg block is pushed up along the slope as shown. The coefficient of kinetic friction is…

Q: For the acceleration analysis question, how do you find tangential acceleration ab (a^t ab)?

A: The tangential acceleration of B relative to A, aab is a component of the total acceleration of B…

Q: A ceramic with KIc = 4 MPa m1/2 contains pores with radius a = 5 µm due to incomplete sintering.…

Q: 9-53. Determine the location y of the centroid C of the "roll-formed" member. Neglect the thickness…

A: Determine the location y of the centroid C of the "roll-formed" member.Neglect the thickness of the…

Q: Calculation of Limits using ANSI B4.1 Standard Tables, when one of the design Features Exists. When…

A: Given:The nominal shaft diameter is .For Interface (force fit):The upper limit of the shaft diameter…

Q: A disk with mass m and radius R is released from rest at a height h and rolls without slipping down…

A: The disc rolls without slipping.

Q: 20. For a tightly stretched string with 5 evenly spaced masses and Use MatLab to determine: a) the…

A: Disclaimer:Hello. Since your question has multiple sub-parts, we will solve the first three…

Q: The curved beam in the figure has a circular cross section 50mm in diameter. The inside diameter of…

Q: 1. The figure below shows a cam and follower. What is the pressure angle at the position shown? Use…

Q: You are given the task to evaluate the following two machines. The requirement of the machines is to…

A: Given:

Concept explainers

Combined Loading

Any functioning component, such as machine parts, structural members, pressure vessels, and so on, are all under the influence of more than one force. When anybody is under the influence of more than one force such as shear forces, bending moments, axial forces, torsion, and so on, then such body is said to be under combined loading. A very practical example of combined loading is the crankshaft of an internal combustion engine (IC engine). The crankshaft of the IC engine is under high rpm, which is caused due to the torsional forces. Due to the presence of piston, counterbalances, and internal imbalances, the crankshaft experiences lateral forces and due to the rise in temperature, the crankshaft undergoes thermal expansion, which pulls the crankshaft along the axial direction and lateral direction. The presence of unbalanced loads along the periphery of the crankshaft also induces a bending moment.

Question

books' answers are second picture

12-41. Determine the displacement at x = 7 m and the
slope at A. El is constant.
X
4 m
3 kN/m
-3 m
50 kN
3 m-
B

12-41
dv
dx
0₁
V
v|x=7
1
ΕΙ
1
=7 m
12.3x²0.5.x³ + 0.5
< x-4 >³ -25 < x-7>² kN·m²,
-278.7
279kN · m²
ΕΙ
4.10x³0.125x4 +
0.125x4>4 -8.33 < x-7>³ kNm³,
22 JAN
EI-278.7x
835kN - m³
EI

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1: Given

VIEW

Step 2: Calculation of reaction force and moment equation

VIEW

Step 3: Calculation of slope at A and deflection at x =7 m

VIEW

Solution

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 4 steps with 17 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

Determine the displacement at B. EI is constant.
A force of 10 kN is applied to the hook. If the CB cable is made of steel (E= 200 GPa) and has a diameter of 8.5 mm, determine its displacement. Consider the distance CB shown below as the initial length.
The rigid bar is supported by the two short white spruce wooden posts and a spring. If each of the posts has an unloaded length of 1 m and a cross-sectional area of 600 mm2, and the spring has a stiffness of k = 2 MN >m and an unstretched length of 1.02 m, determine the vertical displacement of A and B after the load is applied to the bar.
If the 20-mm-diameter rod is made of A-36 steel and the stiffness of the spring is k = 50 MN>m, determine the displacement of end A when the 60-kN force is applied.
The 6-hp reducer motor can turn at 1200 rev>min. If the shaft has a diameter of 5 8 in., determine the maximum shear stress in the shaft.
The pump operates using the motor that has a power of 85 W. If the impeller at B is turning at 150 rev>min, determine the maximum shear stress in the 20-mm-diameter transmission shaft at A.
The gear motor can develop 1 10 hp when it turns at 300 rev>min. If the shaft has a diameter of 1 2 in., determine the maximum shear stress in the shaft.