AP10.1 A three-axis pick-and-place application requires the precise movement of a robotic arm in three- dimensional space, as shown in Figure AP10.1 for joint 2. The arm has specific linear paths it must follow to avoid other pieces of machinery. The overshoot for a step input should be than 13%. (a) Let Ge(s) K, and determine the gain K that sat- isfies the requirement. Determine the resulting settling time (with a 2% criterion). (b) Use a lead network and reduce the settling time to less than 3 seconds. FIGURE AP10.1 Pick-and-place robot. Motor 4 Motor 1 R(s). Ge(s)

AP10.1 A three-axis pick-and-place application requires the precise movement of a robotic arm in three- dimensional space, as shown in Figure AP10.1 for joint 2. The arm has specific linear paths it must follow to avoid other pieces of machinery. The overshoot for a step input should be than 13%. (a) Let Ge(s) K, and determine the gain K that sat- isfies the requirement. Determine the resulting settling time (with a 2% criterion). (b) Use a lead network and reduce the settling time to less than 3 seconds. FIGURE AP10.1 Pick-and-place robot. Motor 4 Motor 1 R(s). Ge(s)

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Write and compare the equation of mechanical and electrical SHO? And a mass stand in floor which execute SHM vertically at 5hz frequency .show that mass losses contact with floor if displacement exceed 1 cm.?
a mass stand in floor which execute SHM vertically at 5hz frequency .show that mass losses contact with floor if displacement exceed 1 cm.?
It is observed from the magnitude plot of a compliance transfer function of a mass spring damper that the value at a very small frequency 0.0001 is 3.71 meters and at resonance 1.10 rad/s is 7.10 meters. What is the natural frequency, damping coefficient, stiffness, and mass of the system?
Figure 2 shows an electrical motor with mass M=13 kg located at the middle of pinned-pinned beam. A damper with damping coefficient of c=59 N.s/m is also attached to the beam at point A . Considering Young’s modulus of the beam E=98 GPa, moment of inertia of the beam I=18 mm4, length of the beam L=1 m, unbalance mass of m0 =1.9 kg, eccentricity e=2.8 mm, and zero initial conditions, find the steady state amplitude of point A at resonance in millimetre (mm).
Suppose a spring mass damper system with k=4000N/m, m=10kg,and c=40N-s/m Find the steady-state and total response of the system under harmonic force F(t)=200 cos t N and the initial conditions x0=0.1m and ̇x0'=0
*An air compressor of 450 kg operates at a constant speed of 1750 rpm. Rotating parts are well balanced, except for the reciprocating part (mass is 10kg and crank radius is 100mm). The mounting introduces a viscous damping of damping factor 0.15. a) What would be the frequency ratio only 20% of the unbalanced force is transmitted to the foundation? b) Find the natural frequency of the system. c) Find the stiffness of the spring for the mounting. d) Find the amplitude of the Unbalance force. e) Find the amplitude of force transmitted to the foundation
alas 30 For a damped one DOF system where m, c, andkare shown below: (a) k = 10 N/m, m 10 kg, c = 10 kg/s, (b) k = 2.5 N/m, m 10 kg, c = 10 kg/s, (c) k = 1 N/m, m = 10 kg, c = 10 kg/s. Calculate for each case the value of natural frequency in rad/sec; time of period in sec; critical damping coefficient, damping ratio; Are these systems overdamped, underdamped, ?or critically damped 30.
Q3.Consider a spring–mass–damper system with m = 80 kg, c = 15 kg/s, and k = 1500 N/m with an impulse force applied to it of 1200 N for 0.01 s. (C) Calculate the damped natural frequency of the system (D) Calculate the system response to the impulsive force at time t = 1 s
A centrifugal fan with a rotational speed of 1500 rpm has a weight of 1200 N and an imbalance of 30 kg-cm.The fan is found to emit a high level of noise while operating, vibrating the floor on which it is placed. To provide 90% insulation using rubber wedges with a dimensionless damping coefficient of 0.15 What should the resistance of the rubber wedges be? What will be the maximum value of the force transmitted to the ground in this case?
Consider a spring-mass-damper system with k=4000N/m, m=10kg,and c=40N-s/m Find the steady-state and total response of the system under harmonic force F(t)=200 cos t N and the initial conditions x0=0.1m and ̇x0'=0
Using a rotary drum filter (diameter is 1.5m as well as its width) rotates at 5rpm and submerged in an open tank of the slurry that has a depth of 1/3 of the equipment’s diameter. Pressure inside is 32 kilopascal. Determine the time required to yield three times 21.42 m^3 which is the volume of filtrate. There is no filter resistance.