Determine the current I2 for the transformer in Figure if the flux in the core is 1.5x10³ Wb. 1₁ (2A) N₁ = 60 turns 1₁ 20 1.8 1.6 1.4 1.2 1.0 0.8 0.6 +B(T) 0.4 0.2 300 600 Sheet steel .d Area (throughout) = 0.15 x 10³ m² labeda = 0.16 m 900 1200 1500 1800 2100 2400 Cast iron 2700 3000 3300 Sheet steel Cast steel N₂ 12 = 30 turns 4200 4500 H(Alm)

Determine the current I2 for the transformer in Figure if the flux in the core is 1.5x10³ Wb. 1₁ (2A) N₁ = 60 turns 1₁ 20 1.8 1.6 1.4 1.2 1.0 0.8 0.6 +B(T) 0.4 0.2 300 600 Sheet steel .d Area (throughout) = 0.15 x 10³ m² labeda = 0.16 m 900 1200 1500 1800 2100 2400 Cast iron 2700 3000 3300 Sheet steel Cast steel N₂ 12 = 30 turns 4200 4500 H(Alm)

Electric Motor Control

10th Edition

ISBN:9781133702818

Author:Herman

Publisher:Herman

Chapter4: Symbols

Section: Chapter Questions

Problem 7SQ: The symbol shown is a(n) a. iron core transformer. b. auto transformer. c. current transformer. d....

See similar textbooks

Similar questions

Q1- The given ferromagnetic core relative permeability is 800. Determine the total reluctance of the core. 35 cm 10 cm 20 cm 5 cm 15 cm 45 cm 15 cm 15 cm 10 cm
The path of a magnetic flux in a transformer should have O High resistance O Low reluctance O Low resistance O High reluctance
For figure (1)draw and calculate the voltages waveform across each half of secondary winding and across load when 100sin2π60t applied across the primary, then find PIV.
For the following magnetic circuit, the flux density is 1 T and magnetic field intensity is 700 At/m. The material of the core is d C cast iron cast steel sheet steel None of the above
The ohmic resistance of a large magnetic contractor is measured to be 25 ohms. A 200V is impressed on the contractor and the current is taken as 5A. Determine the inductance in mH and the reactive power of the load. The frequency is 60 HZ
circut for the core. (₁ For the ferromagnetic core shown in the gure below draw the magnetic The magnitudes of the reluctances are not important but clearly indicate on your circuit every reluctance which should be calculated for the given core. 10 15 = 0.5A d DNI 15 0.03 N2 1₂ = 0.1A 9
Transformers.
A single-phase transformer has 480 turns on the primary and 90 turns on the secondary. The mean length of the flux path in the core is 1.8 m and the joints are equivalent to an airgap of 0.1 mm. The value of the magnetic field strength for 1.1 T in the core is 400 A/m, the corresponding core loss is 1.7 W/kg at 50 Hz and the density of the core is 7800 kg/m3. If the maximum value of the flux density is to be 1.1 T when a p.d. of 2200 V at 50 Hz is applied to the primary, calculate: a. the cross-sectional area of the core; b. the secondary voltage on no load; c. the primary current and power factor on no load
Q5. For the following center tapped transformer, show the waveform across each half of the secondary winding and across R, when a 100 V peak sine wave is applied to the primarywinding. What is the PIV rating must the diodeshave? (Use constant voltage drop model for the Silicon diode) D IN4001 OV 10 kN IN4001 DELL
In transformers, the flux lost in the air is called nd as SKW. If th
What will be the value of the twiddle factor: W42
In transformer, the eddy current loss can be minimized by O using thin size copper conductors O using magnetic material with low permeability laminating the core O using magnetic material with high permeability