A circuit is shown to the right. a. Is this an example of positive feedback or negative feedback? b. If the circuit is an amplifier, what is the gain and is it inverting or noninverting? If the circuit is a comparator calculate the threshold voltage R2 1 ΚΩ mm R1 5 ΚΩ MM OA V_in sine 1 kHz +12V -12V V_out

A circuit is shown to the right. a. Is this an example of positive feedback or negative feedback? b. If the circuit is an amplifier, what is the gain and is it inverting or noninverting? If the circuit is a comparator calculate the threshold voltage R2 1 ΚΩ mm R1 5 ΚΩ MM OA V_in sine 1 kHz +12V -12V V_out

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

- V2 15Vdo 3 U1A R1 2 1k V- LM324 1k V3 15Vde | VOFF = 0 VAMPL = 1 FREQ = 2k AC = 0 0. R2 Figure 4. Operational amplifier circuit. What frequency does the output voltage (across R3) have? What is the amplitude of the output voltage? From the output waveform and the input waveform, determine the gain of the op-amp circuit. Does this match with what you predicted? How could you change this circuit so that the output voltage would be nearly the same as the input voltage? What purpose would that serve? Can you modify the existing circuit and verify this experimentally? What is the phase difference between the output and input voltage? Derive the transfer function for the output-input relationship for the operational amplifier. How would the gain and the output change if a capacitor were in the feedback path instead of a resistor? (Examine the circuit using phasors and impedance and circuit analysis techniques). -w-
If I have an input sine wave in a peak detector circuit I know the output the the first op amp (that will feed back into the negative terminal) should be a little larger than the input (this is why you add a second op amp). I'm not understanding it graphically. Splitting up the circuit say you have the first op amp and the diode (no capacitor or second op amp). the output should be only the positive part of sine wave, and the amplitude will be the amplitude input minus .6V from the diode drop, right? Then adding the capacitor it keeps the same amplitude but makes more DC. with the second op amp this makes it so the capacitor doesn't discharge (which is what keeps the voltage proper up I think?) With my logic here, the voltage feeding back into the first op amp negative terminal is the voltage input, minus a diode drop. So Vin > V- (voltage feeding back into the negative terminal). Which I'm pretty sure V- is supposed to be larger. So I think I'm misunderstand something here. Please…
.
An op-amp has a maximum output voltage swing between ± 14 V. The feedback resistors are R1 = 1.5 KQ, R2 = 7.3 k2, and R3 = 7.6 k0. The input voltage (Vin) is Vin = 0.2 V. What is the output voltage (Vout) to within 1% accuracy? o + Vin Vout= M r₁ ww + HI r3 V 0 + Vout Report questi
In the voltage regulator circuit shown in the figure, the op-amp is ideal. The BJT has VBE=0.7 V and Beta = 100, and the Zener voltage is 4.7 V. For a regulated output of 9 V, the value of R (in Ohms) is Express answers in two decimal points. Show solution on your answer sheet. V = 12 V Vo = 12 V 1 k2 1 k2 AV2 = 47 V %3D ww
The operational amplifier (op-amp) in Figure 1 is an ideal op-amp with maximum output voltage, vO(max) is +12 V and the minimum output voltage, vO(min) is -12 V. A sine wave with ±5V peak-to-peak voltage is applied as the input, vin as shown. For each of the following conditions, derive or explain the relationship between output voltage, vo and input voltage, vin, and then draw the input and output voltage waveforms on same graph. Label the x-axis, y-axis, peak voltages and units. 1.R1 = R2 = R3 = 10 kΩ and RF = 3R1. 2.R2 = R3 = 10 kΩ, RF = 3R2 and R1 is broken (open circuit). 3.R1 = R2 = R3 = 10 kΩ and RF is broken (open circuit). 4.R1 = R2 = 10 kΩ, RF = 3R1, R3 is broken (open circuit) and the op-amp’sinverting and non-inverting terminals are accidently interchanged where node ‘x’ is connected to the non-inverting input while node ‘y’ is connected to the inverting input of the op-amp.
Write a formula forVout (b) Non-inverting dc amplifier
draw the block diagram of op-Amp
An op-amp has an open-loop gain of 105 and an open-loop upper cutoff frequency of 10 Hz. If this op- amp is connected as an amplifier with a closed-loop gain of 100, then the new upper cutoff frequency is
Figure presents a pressure measuring system of a pipeline. The pressure tapprovides a pressure input to the transducer which resulting voltage output between 0 to200 mV. The voltage output is linearly related to the input pressure with a range of 0 to10 bar. The converter current output I is in mA and related to the voltage input in such,I = 4 – 0.2V, where V is in mV. The current signal is sent to a meter for reading display.Estimate the pressure value when the meter indicates 15 mA using the given equation.
If feedback resistor R₁ = 10k and input resistor R₁ = 2k. Then, The voltage gain of the inverting op-amp Av is O 6 O 5 O -5 O-6