Determine the compressive strength of each sample blocks below. Given the area of the block to be 80,000 mm^2. After determining each compressive strength, determine the average compressive strength of the sample blocks and express your answer in PSI. SAMPLE NO. FORCE (N) COMPRESSIVE STRENGTH 1 3500 2 4200 4500 4 5000 5450 6. 6000 7 6500 8 6745 3.

Determine the compressive strength of each sample blocks below. Given the area of the block to be 80,000 mm^2. After determining each compressive strength, determine the average compressive strength of the sample blocks and express your answer in PSI. SAMPLE NO. FORCE (N) COMPRESSIVE STRENGTH 1 3500 2 4200 4500 4 5000 5450 6. 6000 7 6500 8 6745 3.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Calculate the corresponding depth of uniform stress block in a reinforced concrete beam 50*10 deep reinforced with bars 20-mm in diameter enclosed with 10-mm-dia stirrups when the tensile steel strain is 0.008 and concrete compeession strain is 0.003. f’c = 20 MPa express your answer in 2 decimal places only in mm
2) A given material the linear limit is 1.8 * 106 N/ m? and the ultimate compressive strength is 1.8 *10 N/m² and cross sectional area is 6 *104, If the length change by 20%, What is Y material ? A) 9*105 N / m? B) 9*10 6 C) 6 * 10° N / m ? D) 9 *106 N / m?
Procedure: 1. Compression tests on specimens shall be made as soon as practicable after removal from the moist storage. A 28-day test shall be performed within +-20 hours of the 28thday. Test specimens shall be kept moist by any convenient method during the period between removals from moist storage and testing. They shall be tested in moist condition. 2. All test specimens for a given test age shall be broken within the permissible time tolerance prescribed below. TEST AGE PERMISSIBLE TOLERANCE 24 HOURS +-0.5 HOURS OR 2.1% 3 DAYS 2 HOURS OR 2.8% 7 DAYS 6 HOURS OR 3.6% 28 DAYS 20 HOURS OR 3.0% 90 DAYS 2 DAYS OR 2.2 % 3. With a clean rag or rush clean the bearing faces of the bearing blocks, test the specimens and exclusion controller (elastomeric cps). 4. Rest the specimen on the lower extrusion controller, place the top extrusion controller on the specimen, and check the spacing between the sides of the specimen and the extrusion controllers to ensure no contact between the cylinder…
Two 150 mm * 300 mm concrete cylinders with randomly oriented steelfiber contents of 0 and 2% by weight, respectively. After curing for 28 days,the specimens were subjected to increments of compressive loads until failure. The load versus deformation results were as shown in Table P7.45. Assuming that the gauge length is the whole specimen height, determine the following:a. The compressive stresses and strains for each specimen at each loadincrement.b. Plot stresses versus strains for the two specimens on one graph.c. The initial modulus of elasticity for each specimen.d. The ultimate strength for each specimen.e. The strain at failure for each specimen.f. Toughness. Curves may be approximated with a series of straight lines.g. Comment on the effect of adding fiber on the following:i. Modulus of elasticityii. Ultimate strengthiii. Ductilityiv. Toughness
Describe suction in stress path analysis.
Tension specimens (diameter d0 0.500 in., gage length L0 2.00 in.) made of structural materials A and B are tested to failure in tension. (a) At failure the distances between the gage marks are LAf 2.90 in. and LBf 2.22 in.; the corresponding diameters at the failure cross sections are dAf 0.263 in. and dBf 0.471 in., respectively. Determine the percent elongation in 2 in. and the percent reduction in area for these two materials, and classify each material as either brittle or ductile. (b) From these tensile tests the following data are also obtained: EA 10.0 103 ksi, (Y)A 5 ksi, (U)A 13 ksi; EB 10.4 103 ksi, (Y)B 73 ksi, (U)B 83 ksi. From the data given here, make rough sketches (to scale) of the stress-strain diagrams of materials A and B.
The piece of wood shown below was used in an experiment. During the test it sheared parallel to the wood grain along the dashed line. Determine the average shear stress on that failure plane for a maximum load of P = 1575 lb. The dimensions of the wooden specimen are t = 2.0 in. and L = 6 in. Answer: L Average shear stress = psi
The nominal stress-strain diagram for a specimen having an original diameter of 10 mm and a gauge length of 50 mm is shown below. Using the given nominal stress-nominal strain diagram, answer this question. The inset shows a detailed view of the curve at low strains. 400 350 300 250 Stress (MPa) 200 150 100 50 0 0.00 Stress (MPa) 350 kN 300 250 200 150 100 50 0 0.000 0.002 0.004 0.006 0.008 0.010 0.012 Strain 0.02 0.04 0.06 0.08 0.10 0.12 0.14 0.16 Strain 0.18 What is the maximum force that could be applied to the specimen before it plastically deforms?
Given the torque-angle deformation curve below, estimate the shear modulus in GPa?. Where the length of the specimen is 273mm and the diameter is 19.3mm (Round your answer to nearest integer, e.g. 100, do not add units, use exact value of pi not 3.14) SC.O 45.0 35.0 25.0 20.0 5.0 0.20 040 050 0.60 0.70 0.80 0.90 Angle (") A S en eta ine f Your Answer: Answer Torque (N-m)
Shear box dimensions: L= 49,8 mm W = 49.6 mm 3. Prepare the lab results using the following data: Normal Load (kN) Maximum Shearing Force kN) Specimen Number 1 0.983 0.730 1.470 0.970 3 1.960 1.120 Calculations: Obtain the normal stresses and the shearing stresses for each of the specimen above in КРа Plot maximum skear stresses (peak shear stresses) vs. normal stresses and show the peak strength envelope. Determine the friction angle of the soil material.
S1:Q1 a) Figure 1a provides dimensions of a test sample that is being subjected to a tensile stress. If the stress at section Y-Y is 188N/mm2 and the force is 220 kN, calculate the dimension X. Y 1.8cm- Y Not to scale Figure 1a
Explain the modes of failure in tension test.