An RCC beam is of size 230 mm x 500 mm overall depth and effective cover to compression steel and tension steel are 50 mm. The compression reinforcement consists of 2 nos. 16 mm diameter bar and tension steel consists of 2 nos. 25 mm diameter bars. This doubly reinforced beam is made of M20 concrete and Fe415 steel. For Fe 415 0.05 0.10 0.15 0.20 f.(N/mm) 355 353 342 329 Which of the following is/are true? Actual depth of Neutral Axis (NA) is 131.1 mm. Correct Option This is an under reinforced section. Correct Option C The moment of resistance of this beam is 140.72 kNm. Correct Option The moment of resistance of this beam is 183.455 kNm.

An RCC beam is of size 230 mm x 500 mm overall depth and effective cover to compression steel and tension steel are 50 mm. The compression reinforcement consists of 2 nos. 16 mm diameter bar and tension steel consists of 2 nos. 25 mm diameter bars. This doubly reinforced beam is made of M20 concrete and Fe415 steel. For Fe 415 0.05 0.10 0.15 0.20 f.(N/mm) 355 353 342 329 Which of the following is/are true? Actual depth of Neutral Axis (NA) is 131.1 mm. Correct Option This is an under reinforced section. Correct Option C The moment of resistance of this beam is 140.72 kNm. Correct Option The moment of resistance of this beam is 183.455 kNm.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

B) For reinforced concrete lining, the transverse reinforcement is two times the longitudinal reinforcement.O FalseO True
I need the answer to the question in reinforced concrete
I need the answer to the question in reinforced concrete
30" Design the reinforcement for the T-beam in the middle which carries a live load of 200 lb/ft². The length of the beam is 25 ft. In your design assume concrete with a compressive strength of 3,000 psi density 150 lb/ft³ and Grade 60 Steel. 27" 12" 10'-0" 12" 10'-0" 12"
An RCC beam is of 230 mm width, 500 mm overall depth. Effective cover to compression steel and tension steel is 40 mm. Compression reinforcement consists of 2 nos. 16 mm diameter bars and tension steel consists of 2 nos. 25 mm diameter bars. This doubly reinforced beam is made of M 20 concrete and Fe 415 steel. Find the moment of resistance of this beam by LIMIT STATE METHOD. Table: Stress in Compression Reinforcement in MPa Grade of Steel MPa Fe415 0.05 355 ďld Values 0.10 0.15 0.20 353 342 329 00071
A reinforced concrete beam that is 375 mm wide and 500mm deep must resist a service live load moment of 250 kN-m and a service dead load moment of 150 kN-m. Use f'c-21 MPa and fy=415 MPa. The effective concrete cover is 65mm (to the centroid of reinforcements). 1. Determine the area of compression steel reinforcement (If required. Answer O if not) in mm² 2. Determine the minimum number of 25 mm diameter bars to be provided to satisfy the demand ultimate moment 3. Determine the maximum number of 25 mm diameter bars to be provided to have a tension controlled section Answer 1: 2403.21 correct answer: Answer 2: 9.00 Answer 3: 8.00
Topic: BEAM BEARING PLATES AND COLUMN BASE PLATES - STEEL DESIGN
For the following plan it is required to: 1- Design all beams for flexure and shear, where they have additional 30 kN/m distributed factored load 2- Design the columns. The concrete has a strength of 30 MPa, and the yield strength of the steel is 420 MPa. Show full calculations and neat sketches. All dimensions are in m. I 03 B2 0,3 7 B1 Wu=20 kN/m2 B1
A typical grade beam 300 x 800 is reinforced with 2 - 25M bars and the cover is forconerete cast and permanently exposed to the earth, (f', =30 MPa) Determine the following: (a) the size of the stress block "a" (b) the bending moment “M," (c) the c/d ratio (d) the type of failure (brittle or ductile) based on part (c) (e) check Asmin (equation 2.7) (Code 10.5.1.2) (f) maximum As permitted based on ductile failure (g) determine maximum bar size (2 required) from Table 1.5 based on part f) (h) check spacing requirements 's' Table 2.6 based on part g) (i) check if skin reinforcement is required Table 2.9 and fy = 400mpa please solve asap %3D
3-2 A rectangular section with width b=200mm and depth h=450mm is to carry a design bending moment M=145KN •m. The concrete is of grade C40 and the tensile steel is of HRB400. The tension reinforcement A, is required.
A3. A composite beam and deck system made up of W360x72 at 1000mm o.c. is to span 8m. The deck when cast is to be 100mm thick concrete (25MPA). The shear studs to be used have an ultimate stress capacity of 415MPA and will have a diameter of 16mm. Assuming 100% connection and that the system is shored during casting determine the ultimate moment of the composite W360.
QUESTION 1A concrete floor slab measuring 6 m x 3 m is simply supported on one side brick load-bearing walls along the 6 m sides. The concrete slab is 200 mm thick and reinforced at the bottom as follows. a. Main reinforcement (short span i.e the bars are parallel to the short span), Y12, shape code 34 @ 125 mm centre to centre,b. Distribution reinforcement (long-span i.e the bars are parallel to the long span), Y 10, shape code 20 @ 300 mm centre to centre,c. Concrete cover, 30mm,d. Concrete strength, 40MPa. Draw the reinforcement layout for this slab, in plan and section, indicating all thereinforcement and necessary information required by the contractor. Calculate and indicate the number of bars required on your drawing. You do not need to calculate the bar lengths and the curtailment. Neat drawing please