DETAILS SERPSE10 12.3.OP.004.MI. kg automobile has a wheel base (the distance between the axles) of nd the front axle. Find the force exerted by the ground on each wheel. sont wheel sar wheel

Q: Make the part program using CNC code.        Tool Dia. = 6 mm        depth of cut 3.0 mm…

A: Tool Dia. = D =6 mm depth of cut = d= 3 mm (Use G90 code)  To find: Make the part program using CNC…

Q: (i)A point B lies 50 mm away from H.P, & at the same distance from V.P. Describe its position in all…

A:

Q: Illustrate the correct sequence of the Theory of Accidents by Heinrich? A. B. C. O D. Social…

A: Heinrich's Domino Theory states that accidents result from a chain of sequential events,…

Q: draw the orthographic view of the drawing and identify the alphabets of lines used by pointing out…

A:

Q: さutてosuう +1 U、ズX ) Given. find dd.? dx

A:

Q: Sketch the orthographic projection as per the answer arrangement (a) top view (b) side view (C)…

A:

Q: Consider the following linear equations -7x + 8y + 4z - 7x + (25 – k)y + 3z = 11 - 7x + 8y + (7 –…

A: The given set of equations are:

Q: Briefly describe the action taken by the following G&M command blocks assuming absolute coordinates.…

A:

Q: Convert the octal number 23228 to its hexadecimal number equivalent, (base-8 to base-16).

A: Steps of Conversion: The simplest way is to convert the octal number into a decimal, then the…

Q: nts Simplify the following block diagram: R G H Hint: redraw as: H. S'

A: It is required to simply given block diagram

Q: Draft and annotate the below sketch using AutoCAD Note: colour the hatching lines with different…

A:

Q: . VELOCITY ANALYSIS. For the single-degree-of-freedom mechanism shown below, the angular velocity on…

A:

Q: Could ypu help me with this problem? It should start with something like this: P1=0,0 P2=10,0…

A: The part program for the given drawing uses the Fanuc Cut language. I'll start by identifying key…

Q: 30r 20dls 20 10r 20 20 30 150 100

A:

Q: The figure shows a shaper machine that uses Whitworth quick return mechanism wherein the different…

A: Given Data OA=75cm OP=50cm CA=150cm CD=135 cm

Q: EX7: write a program read any vector and print the odd order only?

A: Required: Program to read vector and print item ad odd order.   all the code with code screenshot…

Q: Illustrate the correct sequence of the Theory of Accidents by Heinrich? A. B. C. D. Social…

A: Heinrich's Domino Theory states that accidents result from a chain of sequential events,…

Q: as soon as

A:

Q: dy Solve the differential equation cos(z) dz

A:

Q: EX6:write a program read any vector and print the odd number only?

A: Note: Here you didn't mention any programming language so we are creating the program in the C++…

Q: QUESTION 3 Code for a clockwise circular move to an end point that is 1 inch over in the X direction…

A: consider the following diagram:

Q: Consider the floating point system F and answer the following questions. Your solution to each part…

A: y=cos6xwe should use dx slice & the washer methodwasher have outer radius R=…

Q: Find the limit. NOTE: Enter an exact limit if it erists. If the limit does not exist, indicate that…

A:

Q: Need full accurate RRL .  For both 1. height of sweet potato plants. 2. programable  speed of a…

A: The question is asking for a detailed review of related literature (RRL) on two distinct topics: the…

Q: Write a MATLAB program that finds the sum for-25 to 5. (Increment by 5). By using (while „loop)

A:

Q: Thank you for this answer. I don't quite understand step 4, 5 and 6 because the operation is not…

A: given; all values given

Q: Write the function of ortho on in an AutoCAD system. When and why we use this command during…

A: Ortho System In AutoCAD, the Ortho mode is used to limit the movement of cursors to certain…

Q: An 'angle plate' is used to A. Hold a workpiece B. Mark various angles on the workpiece and hence…

A: An angle plate is a work holding device used as a fixture in metalworking.

Q: In cone clutch, the power can be transmitted is increased by increasing the turning angle. O…

A:

Q: . Convert the decimal number 35710 into its binary number equivalent.

A: Given: A decimal number is, (357)10 .

Q: Can you help me with this please? For a given part drawing fig. prepares a Part program for a wire…

A: To write a part program for a Wire EDM machine using Fanuc - Cut, we need to consider the geometric…

Q: Write 8 sentences in present continuous form

A: Following sentences are in present continuous form - The boys are playing football after school.…

Q: 01: Write G code to Write the first Letter of you name

A:

Q: Q1: write a program to enter any text and compute its length. Q2: Design a form with a text box. Use…

A: Python Program: str = input("Enter the string: ")                             print("Length of the…

Q: 20 R3 Which tools that can be used to :3 draw the following shape in .AutoCAD 37 23 43 R3 dimension,…

A:

Slope and Deflection

The slope in a deflected beam is described as an angle in radians made by the tangent of the section with the original axis of the beam. The deflection at any point on the axis of the beam is defined as the lateral displacement of the point before and after loading.