Design rectangular sections for the beams, loads, and p values shown. Beam weights are not included in the loads given. Show sketches of cross sections including bar sizes, arrangements, and spacing. Assume concrete weighs 23.5 kN/m'. F, = 420 MPa and f'c= 28MPA. %3D %3D

Design rectangular sections for the beams, loads, and p values shown. Beam weights are not included in the loads given. Show sketches of cross sections including bar sizes, arrangements, and spacing. Assume concrete weighs 23.5 kN/m'. F, = 420 MPa and f'c= 28MPA. %3D %3D

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: Principle of Reinforced/ Pre-stressed Concrete. Please provide clear hand writing. Thank you!…

A: Given : fc = 28 MPa Span, L = 6 m Magnitude of UDL, Wu = ?

Q: What is the shear force to be carried by the reinforcements of a beam subjected to axial tension if…

Q: 2. Another reinforced concrete beam has the following properties: • fy= 60 ksi • f= 5,000 psi • As =…

Q: Q2 : Design the beam showing below for shear by using Ultimate Strength Design method according to…

Q: Locate the centroid y of the composite area. Set a = 8 mm, b = 28 mm, d = 21 mm, h = 44 mm. (Figure…

Q: Solve for the centroid of the given composite structural section and determine the moments of area…

Q: PLEASE WRITE THE COMPLETE SOLUTION NEATLY: A rectangular beam has b = 250 mm and an effective depth…

A: b = 250 mm d = 490 mm fc' = 20.7 MPa fy = 420 MPa As = 3-20mm diameter bar Calculate ultimate…

Q: I x,0= 10 " 1" 4 I y, = y.o r x,0 = 4"X6"X ¼" r y,o = 12" 4"X 8"X 1" 2" 1" 10 "

Q: two span beam subjected to shear and flexure only is reinforced as follows: Given: Stirrup…

A: %pt = Ast / Ac Ac = b * deff

Q: For the section shown, use Whitney's rectangular block to calculate a, ß1 and c, determine the…

A: Given Data:fc=400psiEC=3600ksiand Grade 60 steel fy=60000psiEs=29000 ksi

Q: Given the following properties f a rectangular concrete beam, b = 300mm, d = 500mm, F'c = 20.7MPa,…

Q: Q4: For the RC beam section shown in figure below, find the location of neutral axis (N.A) and the…

A: Given: h = 500 mm d = 450 mm b = 250 mm fc = 30 MPa fy = 420 MPa Es = 200000 MPa Ec = 20000 MPa 3…

Q: 600 150 150 Refer to the figure shown. Given are the following: Unit weight of concrete = 24 kN/m²…

A: Prestressed concrete is a structural material that enables engineers to place preset engineering…

Q: Reinforced Concrete Design-1 Follow ACI Code (American Concrete Institute) Last two…

A: Reference : ACI Code Amount of area of steel required will be ; As As = Mu0.87 fy Z Mu = Ultimate…

Q: A Concrete Masonry Unit Wall is constructed as follows: • Length 8000 mm • Height 4000 mm . There…

Q: Q1) Slab system consist of two-way slab panels shown in Figure below, subjected to superimposed dead…

A: Step 1 Given Dead load = 2KN/m2 Beam dimensions, bw=350mm, h=750mm column dimensions = 350×350mm,…

Q: A center-point loading flexural test was performed on a concrete beam with a cross-section of…

A: Given:- b=15.237cm=152.37mm L=span = 18"=457.2mm Failure load =7549.581lb=33582.20939N Modulus of…

Q: A rectangular beam has a width of 260 mm and an overall depth of 470 mm. concrete cover is 60 mm…

A: Appreciate if there is detailed work with explanation and finds you helpful for ease of…

Q: Given the following properties of the reinforced concrete beam shown, f, = 60,000 psi and fe = 4,000…

A: Given:- The strength of the steel (fy) = 60,000 psi The strength of the concrete (f'c) = 4,000 psi…

Q: reinforced beam will be provided with the reinforcing bars corresponding to 90% of the maximum…

A: (a) Estimation of steel areaThe steel area can be estimated using the following formula:Ast =…

Q: h of the beam section in kN.m. For the beam to sustain a factored moment of 160 kN.m, what will be…

Q: Q3- Three concrete beams were selected for flexural strength test. Results from tests are shown in…

A: NOTE - Since we only answer up to 3 sub-parts, we’ll answer the first 3. Please resubmit the…

Q: Given the concrete (f c=6000 psi) I-beam shown in Figure 1 for the given loading: -draw the shear &…

A: The cross-section of beam is given by I-section shown below

Q: The two pieces of wood, 1.78in. by 4.75 in., are glued together along the 40ᴼjoint. Determine the…

A: From the given data Area A = 1.78 * 4.75 = 8.455 in² Max shear stress in the glue limited to 234…

Q: II. Locate the centroid of the composite area below. Y 50 mm 80 mm R=50mm 250mm R=65mm -- X 50 50 mm…

A: To find centroid of composite area

Q: Problem 1: A singly reinforced rectangular beam has a dimension b = 310mm and d = 410 mm. Factored…

Q: PLACE YOUR ANSWERS HERE. I x,0= 10 1" I y,0 = r x,0 = 4"X6"X ½" r y,0 = 12" 4"X 8"X 1" 1" 12 "

Q: 1. Consider the shear diagram below for the simply supported rectangular beam. Compute the…

Q: Find maximum factored uniformly distributed load "Wu" that can be supported?, where fe'=30 Mpa and…

A: Answer f'c = 30 Mpa fy = 400 Mpa As = 3-ϕ16 d = 0.536 m = 536 mm L = 6 m Calculations shown in…

Q: A square post which is made up of two parts is glued at plane abcd with the angle a = 30° with the…

A: Solution: Given Data: α=30°Allowable compressive stress=5.2 MPaAllowable shearing stress=3.5 MPaP=36…

Q: Calculate the Flexural strength (Modulus of rupture) of concrete of 4"x 4"x12" beam tested 4500 lbs…

A: The flexural strength of the concrete is calculated by Centre point loading method, σ = 3PL2bd2…

Q: 1. A rectangular beam has b = 300 mm and an effective depth of 525 mm. 28th day compressive strength…

Q: Refer to the figure shown. 1450 300 Given are the following: fc' 35 MPa fou = 1,500 MPa Aps = 1,800…

A: Given f'c= 35 Mpa fpu = 1500 Mpa

Q: The floor shown below has a constant thickness (h) of 190 mm, and is supported by beams at each grid…

A: Given: Details of floor having constant thickness of 190 mm and supported by beams at each grid…

Q: Q3- Three concrete beams were selected for flexural strength test. Results from tests are shown in…

Q: Given a beam section b angle D = 450mm * 950mm M*=1500kNm, f_{c}' = 32MPa f_{5y} = 500MPa and the…

Q: A third-point loading flexural test was performed on a concrete beam with a cross-section of…

A: b=15.197cm=151.97mmL=span = 18"=457.2mmFailure load = 11599.009lb=51594.962700076845NModulus of…

Q: PROBLEM 3: Determine centroid of the composite figure. Refer your final answer to x and y axis. 3"…

Q: Determine the following: a. How many additional ɸ16 tensile bars are required? b. What is the new…

Q: I. Problem Solving: Answer what is being required. Show you complete solution. 1. Compression test…

A: As per Bartleby guidelines we are supposed to answer only one Question if the number of questions…

Q: Plz, solve this problem in all its parts. Reinforced Concrete Design-1 Follow ACI Code…

A: Hi! Thank you for the question As per the honor code, We’ll answer the first question since the…

Q: 2. Problem 4: Calculate the nominal strength of the section. 2.25 f 3,000 psi 2.50" #9 BARS Grade 60…

Q: Situation 2: A rectangular beam has the following properties. Assume 12 mm stirrups. Assume a single…

A: A structural element that primarily resists loads applied to the beam's axial direction laterally.…

Q: Jy Unit weight of concrete = 150 lb/cu.ft. Find the required Shear reinforcement needed at the most…

A: Longitudinal section of beam:Cross-section of beam:

Q: Problem 2.7 A reinforced concrete beam has the following data. Beam width, b=300 mm Effective depth,…

A: Given: b = 300 mm d = 600 mm d' = 60 mm fc = 27.5 MPa fy = 415 MPa

Q: Given the properties of a reinforced concrete beam with section below: • Unit weight of concrete 24…

A: Given, Unit weight of concrete =24 kN/m3 Concrete compressive strength fck=34.5 MPa Steel yield…

Q: two span beam subjected to shear and flexure only is reinforced as follows: Section @ midspan @…

A: Given, Stirrup diameter =10 mm Concrete compressive strengthfc=21 MPa Steel rebarfy=415 MPa Steel…

Concept explainers

Design criteria for structural loading

The different loads such as loads due to self-weight (dead load) and external loads such as live load, wind loads, seismic load, snow load, and other loads and load combinations that influence the design of a building are called structural loading. The nature of the applied load differs from changes in the location, design, and type of materials used. The design criteria require that structures must be designed and constructed to be able to withstand all load types that are expected to act upon the structure and render its usage for the designated purpose. The structural members such as beams, slabs, columns, and foundations help the structure to withstand the applied load. There are different institutes such as ASCE and ACI that provide building design codes to assure minimum safety requirements and quality of the structures.

Question

PL = 60 kN
Wn =6 kN/m
Wz = 10 kN/m
3 m
3 m
–
P=

Design rectangular sections for the beams, loads,
and p values shown. Beam weights are not included
in the loads given. Show sketches of cross sections
including bar sizes, arrangements, and spacing.
Assume concrete weighs 23.5 kN/m'. F, 420 MPa
and f 'c 28MPa.
%3D
%3D

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1: Introduction

VIEW

Step 2: Given data

VIEW

Step 3: Design constraints

VIEW

Step 4: Conclusion

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 4 steps with 1 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

Question 38 A simply supported beam 300 mm wide, 500 mm deep and spans 5 m supports a service super imposed dead load of 6 kN/m and service live load of 9 kN/m. Concrete strength f’c = 21 MPa and steel yield strength fy = 415 MPa. Concrete cover to bar centroid is 70 mm. Determine the required amount of tensile reinforcement in mm^2 as per provisions of NSCP 2015. Write your final answer to the nearest whole number.
Using the following details, Design the shear reinforcement along the length of the beam if it is reinforced with 3-25mm diameter rebars. Sketch the stirrup pattern. Unit Weight of Concrete = 23.123 kN per cu.m. Shear Strength Reduction Factor = 0.75 Clear Cover = 40 mm Beam dimension is 300mm x 500mm Stirrups, fy = 275 MPa Main Reinforcing Steel, fy = 415 MPa Concrete, fc' = 27.5 MPa. The 3-m-span cantilever beam (the free end on the right side) carries a uniform dead load of 30 kN/m (Beam weight not included), and a varying live load of 15 kN/m that reduces to zero at the end of the beam.
A prestressed concrete has a rectangular section with the following data: b = 400 mm, h = 800 mm, L = 12 m, f. = 69 MPa, fp = 1,860 MPa. f = 1,600 MPa, f. = 1,012 MPa, f = f = 415 MPa, Aps = 690 mm², A, = 1,290 mm², A, = 400 mm², d₂ = d₂ = 725 mm, d'= 75 mm. Determine the nominal moment resistance (kN-m). Make assumptions when necessary.
The two pieces of wood, 2.94in. by 4.76 in., are glued together along the 48ᴼjoint. Determine the maximum safe axial load P (in lb) that can be applied if the shear stress in the glue is limited to 275 psi. Round off the final answer to three decimal places.
Question 1 The T-section beam shown in the figure below is required to resist an ultimate design moment of Mu = 460 kN m. The characteristic materials strengths are fy = 410 N/mm2 and fou 20 N/mm2. Calculate the area of reinforcement required. %3D b = 685mm ht = 90 mm d = 560 mm bw = 300 mm
:In the given composite structural section determine the quantities placedinthe table below. Answers placed are final and NO ERASURES are to be made. PLACE YOUR ANSWERS HERE. 10 " Ix = 1" Iy= 4"X6"X %" rx = ry= 12" 4"X 8"X 1" 2"
Calculate the uniform load w (in addition to the beam weight) that will cause the section shown to begin to crack if used as a 28-ft simply supported beam. Use normal weight concrete with L=4000 psi. f = 60,000 psi, E₁=29,000 ksi, and the reinforced concrete weight = 150 lb/ft³. 4 in. 28 ft 4 in. 22 in. 30 in. 2 in. 2 in. 3 #9 ● ||—12 in—-|
Given the concrete (f c=6000 psi) I-beam shown in Figure 1 for the given loading: -draw the shear & moment diagrams -determine Vmax & Mmax -using ASD (Allowable Stress Design) method, check to see if the given loading produces stresses within the given allowable range (check both Omax & Vmax) Using ACI 318-99, allowable stresses are -for flexure, f = .45f'c -for shear, v. = 1.1√f. (HINTS: 8² -note that the beam is symmetric about both axes -Ix for a triangle is (1/36)bh³+Ad² ) 30 kips 16' 10 kip/ft 22' 20 kips 3'-4' -1-6 -1'-6" Figure 1 1'-
Hope your help concrete design (CE410) thanks
Find the minimum theoretical width and height of a rectangular concrete section that will make the beam failure sufficiently ductile. Given: Two layers of 2-Ø25 mm bottom reinforcements fy=414 MPa f'c=35 MPa stirrup diameter=minimum required clear cover=minimum value for beam vertical clear spacing bet. Iayers=minimum value for beam height-to-width ratio=2.0 Note: Ductile failure occurs in beams when the extreme reinforcement layer is strained to 0.004 or greater.
Note: Read the question carefully and give me both right solutions with clear calculations. Don't copy from already available solutions.
Civil Engineering The section of a beam near a column is given below. Area of the top reinforcement is 800 mm2 and bottom reinforcement is 300 mm2. Is the section under or over-reinforced if the balanced reinforcement ratio is po =0,0209? bw = 200mmd= 300mm bw a) O Under-reinforced since 800 mm2 Asb e) Over-reinforced since 300 mm2 > Asb What is the distance of the neutral axis c from the top of the beam, if the top portion of the beam is in compression. Concrete is C30, longitudinal steel bars are o16 and made of B420C steel. Use design strengths in computation. b = 800 mm, d = 500mm, h For C30 concrete k = 0.82. your = 100 mm, b, = 300 mm. Hint: a) 53 mm b) O 46 mm c) O 20 mm 32 mm 26 mm