Design circuit that has an input w and an output z. The circuit is a sequence detector that produces z = 1 when the previous two values of w were 00 or 11; otherwise z = 0. Use W=0101100010101110101011100010 a) For this problem design the circuit using JK flipflops, draw the state diagram, true table, logic circuit

Design circuit that has an input w and an output z. The circuit is a sequence detector that produces z = 1 when the previous two values of w were 00 or 11; otherwise z = 0. Use W=0101100010101110101011100010 a) For this problem design the circuit using JK flipflops, draw the state diagram, true table, logic circuit

Electric Motor Control

10th Edition

ISBN:9781133702818

Author:Herman

Publisher:Herman

Chapter22: Sequence Control

Section: Chapter Questions

Problem 6SQ: Draw a symbol for a solid-state logic element AND.

See similar textbooks

Similar questions

ii) For the circuit shown in Figure B9, a. Find logic functions for Y and Z. b. Simplify function Z using Boolean algebra. Y Figure B9 AB
Q5: Determine the output boolean expression for logic circuit as shown in figure below. x- y- D z-
Design a combinational circuit with the four inputs A,B.C, and D, and three outputs X, Y, and Z. When the binary input is odd number, the binary output is one lesser than the input. When the binary input is even number the binary output is one greate than the input. Implement the function using multiplexers with minimal input and select line.
USE DIGITAL LOGIC AND DESIGN Part 1: In Figure_4; we have 4-bit Comparator using 2-bit Comparators block. You have to satisfy given condition by applying all data on figure 4. At the end, given condition should produce HIGH output and other two should be LOW. A3 A2 A1 A0 = 1101 and B3 B2 B1 B0 = 1110 Figure_4 Part 2: The serial data-input waveform (Data in) and data-select inputs (S0 and S1) are shown in Figure_5. Determine the data-output waveforms from D0 through D3. Figure_5 Part 3: Decoder can be useful when we have to decode some specific numbers from their equivalent code. Figure 6 has a concept of 3 to 8 line decoder from which you have to generate output waveform from D0 to D7 with proper relationship to input. Figure_6 Part 4: The data-input and…
H.W :- 1) A four logic-signal A,B,C,D are being used to represent a 4-bit binary number with A as the LSB and D as the MSB. The binary inputs are fed to a logic circuit that produces a logic 1 (HIGH) output only when the binary number is greater than 01102-610. Design this circuit. 2) repeat problem 1 for the output will be 0 (LOW) when the binary input is less than 01112-710- Saleem Lateef
Consider the circuit below. The switches are controlled by logic variables such that, if A is high, switch A is closed, and if A is low, switch A is open. Conversely, if B is high, the switch labeled is open, and if B is low, the switch labeled is closed. The output variable is high if the output voltage is 5V, and the output variable is low if the output voltage is zero. a. Write a logic expression for the output variable. b. Construct the truth table for the circuit. A Logic 1 5V(+ B C Logic 0 R
Design a logic circuit with four inputs and one output that will produce "l" in the output only if the input patterns have odd number of zeros. a) Write the Boolean equation for the circuit in the simplest SOP form. b) Draw the logic circuit for the above equation in its simplest form. c) Re Design the logic circuit using NANI) gates only?
Q1/ Draw the logic circuit after simplify the circuit show below using K. map: A Y. C- Add filo B.
A logic circuit is implemented as below. The logic function f is the function of x1 and x0. Write the function f expression.
answer this plss the subject is logic circuitss
Design the following combinational logic circuit with a four-bit input and a three-bit output. The input represents two unsigned 2-bit numbers: A1 A0 and B1 B0. The output C2 C1.C0 is the result of the integer binary division A1 A0/B1 B0 rounded down to three bits. The 3-bit output has a 2-bit unsigned whole part C2 C1 and a fraction part CO. The weight of the fraction bit CO is 21. Note the quotient should be rounded down, i.e. the division 01/11 should give the outputs 00.0 (1/3 rounded down to 0) not 00.1 (1/3 rounded up to 0.5). A result of infinity should be represented as 11.1. A minimal logic implementation is not required. (Hint: start by producing a truth table of your design).
Electrical Engineering Task Figure shows a BCD counter that produces a four-bit output representing the BCD code for number of pulses that have been applied to the counter input. In particular, the DCBA outputs will never represent a number greater than 1001,-91, (MOD-10). (MSB) Logic BCD counter circuit HIGH only when DCBA=210-310, or 910 a. Draw the logic circuit using the minimum expression and then explain its operation. B