Design a voltage to current converter amplifier. Assume that you have 5v input voltage to the non-inverting input with a frequency of 60hz and another input voltage to the inverting input with a frequency of 60hz, place it before the input resistance. What should be the value of your voltage input in inverting input and input resistance to get a reading of 38.22mA at exactly 22.20ms and what is the shape waveform of the current? Cursor 1 I(R2) Horz: 22.204037ms Vert: 38.277447MA What is the value of Rin in ohms? No need to include the Units. Rin = ohms

Design a voltage to current converter amplifier. Assume that you have 5v input voltage to the non-inverting input with a frequency of 60hz and another input voltage to the inverting input with a frequency of 60hz, place it before the input resistance. What should be the value of your voltage input in inverting input and input resistance to get a reading of 38.22mA at exactly 22.20ms and what is the shape waveform of the current? Cursor 1 I(R2) Horz: 22.204037ms Vert: 38.277447MA What is the value of Rin in ohms? No need to include the Units. Rin = ohms

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

In all of the circuits, the voltage of the Vin input signal is 200mVp and the frequency is 1KHz. will be applied as Perform DC and AC analyzes
One way to measure the slew-rate limitation of an op amp is to apply a sine wave (or square wave) as the input to an amplifier and then increase the frequency until the output waveform becomes triangular. Suppose that a 1-MHz input signal produces a triangular output waveform having a peak-to-peak amplitude of 4 V. Determine the slew rate of the op amp.
In the self-biased FET amplifier in the figure, Vdd=20V Rs=1kohm Vgsq=-2.6V IDq=2.6mA. It has values of Idss=8mA, Vp=-6V gos=25mikroS. 12mV a.c. to transistor input. What should be the Rd resistance value so that the output voltage is -24.85mV when voltage is applied? answer: 3.3kohm, 3.6kohm, 4.5kohm, 3.9kohm, 4.2kohm is one of the answers.
DEPAR/PAPPA, OP Q4: . For the following circuit, the value of Boc is 200. A) Calculate the collector current B) Determine the collector to emitter voltage. Re 47 L ke 10 V -I5 V
3J Calculate the the Input Voltage of a non-inverting op-amp with the following parameters Rf = 360KOhms, Ri= 12kOhms, and Vi = 2.4V. a.0.934 mV b.9.34 V c.77.42mV d.93.4 microV
This is a practice question from my Introduction to Electronics course. Please talk me through the process. Thank you for your assistance.
Use the following circuit to design an oscillator of 5 kHz output. The amplifier used in this oscillator is multistage C.S. with source resistance amplifier. The design must be with minimum No. of stages. Use the following FET parameters Id=2mA, gm=2.5 ms and rds = 40kN. Use VDD = 24V L R Vo Vi
true or false A voltage buffer circuit provides a means of matching between input signal and a load by using a stage having unity voltage gain
5. If you have this relationship between the input and output voltage Vou=1.5 Vin+2 in which 2 is a bias. Design a circuit that will remove the bias and make the relationship between the input and output as Vou=1.5 Vin. We have a dual supply of ± 12 V available and we need to drive a 10 kQ load. Test your designs under different input voltages and verify that your output voltages are within + 5% of the calculated ones. Simulate the circuit in Multisim and then implement it practically. Prepare a full report about the experiment.
for the common -base configuration using a common value of 30 ohm for the input resistance, input voltage is 200mv and RI=3000 ohm, find the voltage amplification. * 50v 30v 25v 20v
A certain op-amp has an open-loop gain of 80,000. The maximum saturated output levels of this particular device are + 12 when the dc supply voltages are ±15. If a differential voltage of^15 mV rms is applied between the inputs, what is the peak-to-peak value of the output?
Book:Operational amplifiers and Linear integrated circuits Chap#03