Design a three-bit counter like circuit controlled by the input w. Ifw = 1, then the counter adds 2 to its contents, wrapping around if the count reaches 8 or 9. Thus if the present state is 6 or 7, then the next state becomes 0 or 1, respectively, after adding 2. If w = 0, then the counter subtracts 1 from its contents, acting as a normal down-counter. Use JK flip-flops in your circuit.

Design a three-bit counter like circuit controlled by the input w. Ifw = 1, then the counter adds 2 to its contents, wrapping around if the count reaches 8 or 9. Thus if the present state is 6 or 7, then the next state becomes 0 or 1, respectively, after adding 2. If w = 0, then the counter subtracts 1 from its contents, acting as a normal down-counter. Use JK flip-flops in your circuit.

Database System Concepts

7th Edition

ISBN:9780078022159

Author:Abraham Silberschatz Professor, Henry F. Korth, S. Sudarshan

Publisher:Abraham Silberschatz Professor, Henry F. Korth, S. Sudarshan

Chapter1: Introduction

Section: Chapter Questions

Problem 1PE

See similar textbooks

Similar questions

Design and implement a circuit that operates as a gated binary counter. When the counter is enabled, it should increment from 000, 001, ..., 111, and finally roll over back to 000 and repeat the sequence. When disabled, the counter should hold its present value. Choose the flipflop that allows you to minimize the number of additional gates needed to realize this functionality.
Design a modulo-6 counter, which counts in the sequence 0, 1, 2, 3, 4, 5, 0, 1, .... The counter counts the clock pulses if its enable input, w, is equal to 1. Use D flip-flops in your circuit. Repeat Problem 6.23 using JK flip-flops. Repeat Problem 6.23 using T flip-flops.
Design a sequential circuit with two JK flip-flops A and B and two inputs E and F. If E = 0, the circuit remains in the same state regardless of the value of F. When E = 1 and F = 1, the circuit goes through the state transitions from 00 to 01 to 10 to 11 back to 00, and repeats. When E = 1 and F = 0, the circuit goes through the state transitions from 00 to 11 to 10 to 01 back to 00 and repeats.
Design a sequential circuit using T FF in a way where the states are changing in a following way. Show all the necessary steps. 1 1. 10
Simplified the below given Boolean expression f(a, b, c) = (a + b).(b + c) + b.(ā + ē). The number of the 2 input NAND gate needed to implement the simplified expression is
Design a two-bit counter (sequential circuit) using falling edge triggered T-flipflops, with one input line x. When x= 1, the state of the circuit remains the same. When x = 0, the circuit goes through the state transitions byincrementing the state count, i.e., from 00 to 01, 01 to 10, 10 to 11, and 11 to 00, and repeats. Draw circuit diagramof the designed counter. if z=83,Convert z to Base-2, e.g., z= (156)10 = (10011100)2.Provide this bitstream as input to K and draw the timing diagram of the outputs of both the T-flipflops.
Design a unsigned 2-bit counter using J-K flip-flops that increments by one on each clock cycle 0,1,2,3,0,1,2,3,0,... unless an external input R is turned on, which will reset the counter to 0 instead. You need to show the truth table for the circuit and find a simplified expression for each output using a K-map. Show ALL of your work and draw the final circuit.
Question 2: A combinational circuit has 4 inputs (A, B, C, D) and 1 output (F). ABCD represent a majority function. The output of the majority function is equal to 1 if the input variables have more 1's than O's, otherwise the output is 0. a. Construct the truth table of the required circuit. b. Implement the minimized expression of F using 3-level all NAND gate circuit. Implement a 2-1Multiplexer using three-state buffers.
Design and implement using T-FF a synchronous loop counter that counts: 5>3>0>1>6 and back to 5 in a loop. Use the Tina software to implement the circuit of the counter.
In designing synchronous counter for sequence: 0→1→3→4→ 5→7→0, using T flip-flop, if states are named as A, B and C, then TA = O a. TA = B O b. TA = B' c. TA = A' O d. TA = AB
00 A-00 11 c=10 01 10 Z-0 Z-0 Too 01 01 10 11 01 10 00 10, В-01 D-11 Z-1 00 Z-1 1. Draw the state table of the circuit. 2. Implement the sequential circuit that will provide this state diagram using D-Flip-Flops, 8x1 MUX. 3. The design will be made as a mealy model. Draw the new state diagram according to the Mealy model. 10
In designing synchronous counter for sequence: 0→1→3→4→5→7→0, using T flip-flop, if states are named as A, B and C, then TC = O a. TA = B' O b. TA = AB c. TA = A' O d. TA = B