Design a counter that counts in the following order of numbers: 2-3-4- 5-6-7-2-3-. and so on using the JK Flip-Flop, which can also be 'Reset' (active High) manually with a push-button, Synchronous up counter. A. Create a truth table b. Use the Karnaugh Map for this counter purpose c. Generate function result from this counter based on Karnaugh Map

Design a counter that counts in the following order of numbers: 2-3-4- 5-6-7-2-3-. and so on using the JK Flip-Flop, which can also be 'Reset' (active High) manually with a push-button, Synchronous up counter. A. Create a truth table b. Use the Karnaugh Map for this counter purpose c. Generate function result from this counter based on Karnaugh Map

Electric Motor Control

10th Edition

ISBN:9781133702818

Author:Herman

Publisher:Herman

Chapter22: Sequence Control

Section: Chapter Questions

Problem 6SQ: Draw a symbol for a solid-state logic element AND.

See similar textbooks

Similar questions

Design a synchronous BCD Counter based on the following conditions. If last digit of your roll number is odd then design down-counter with JK-Flip Flops by initializing the counter with last digit and count next five states. The counter should cycle back after counting five states. Hint: roll number = 169
Problem Statement: You design a circuit of a decade counter that will count from 0-9 only. You will only be using the following: (a) Button – only 1 button will be used to trigger the counting. (b) Flip flop IC to used as counting circuit with 4 - BITS binary OUTPUT. (c) IC's for Decoding the Binary OUTPUT of Flip-flops to Decimal Output (d) 7- Segment Display to display the OUTPUT from 0-9. Block Diagram: 4 Bit Binary Flip-Flop 7-Segment Display Button Decoder Circuits Circuits
Design 2 bits counter that count down by using T flip flop when input x =1 and counts upwhen x=0. Find the following1. Derive the state table2. Derive the K‐map simplifications.3. Draw the logic diagram
Which one is true for D flip flop? a) It has 2 inputs 1 output b) It has always the output 1. c) The output of it will be equal to its' input. d) It can not be used in logic circuit designs.
Design 1-5 count-up Counters using JK Flip-Flops. 001-010- 011-100- 101- back to 001 03 Required: a) Excitation of Flip-Flop b) State diagram and circuit excitation table. c) Obtain simplified equations using k-map. d) Design logic diagram.
Part B 3. Design a BCD to Excess 3 code converter. 4. What is flip flop? Describe all types of flip flops with diagram and excitation tables.
(d) Figure 6 shows the diagram of a 3-bit ripple counter. Assume Qo = Q1 = Q2 = 0 at t = 0, and assume each flip-flop has a delay of 1 ns from the clock input to the Q output. Fill in Qo, Q1, and Q2 of the timing diagram (shown in Figure 7). Flip-flop Q1 will be triggered when Qo changes from 0 to 1. %3D 3 Qo Q2 T T Clock- Figure 6 Clock 10 15 20 25 30 35 40 45 50 Figure 7
3- Design a counter with a control input. When the input is high, the counter should sequence through three states: 10, 01, 11 and repeat. When the input is low the counter should sequence through the same states in the opposite order 11, 01, 10 and repeat.a) Draw the state diagram and state transition table.b) Implement the counter using D flip-flops and gates.
The figure above shows a synchronous countdown with asynchronous preset. The CE input enables counting when set to 1. The RC output is activated when the count reaches the minimum and CE=1. Design the counter using JK type flip-flops with asynchronous preset and combinational circuitry. Draw the logic diagram of the counter circuit.
Q) You want to design a synchronous counter sequential (sequential) logic circuit. Counting from 9 to 0 and will not count the last digit of your student number. (a) List the steps that you will apply in the design approach. State Chart and State Create the table. (b) Design the sequential circuit using JK Flip-Flop. Explain each step. Desired action show that you have done it. " last digit student num:4 " Not : I want the solution to contain tables and equations, and the electrical circuit resulting from tables and equations, as in the picture that I attached,And if possible, I want the solution on paper if possible.
24: 1’s complement of 1011101 is 0100010 Select one: True False 25: Sequential logic circuits, comprises ___________________________________ logic gates such as flip-flops only logic gates and memory elements such as flip-flops. memory elements such as flip-flops. 27: Find the 1's complement of 01100111.10101 10100100.01101 11110100.11101 10011000.01010 11100100.01001
QUESTION 3 A pattern detector which gives 1 at its 1-bit output when the last four values of its 1-bit input are 1011 will be designed. D flip-flops, AND,OR gates will be used for implementation. a) Draw the state diagram b) Draw the state table. c) Drive the flip-flop input and output Boolean equations. d) Draw the circuit.