Design a 2-bit comparator. The comparator input has two 2-bit numbers A and B. A consists of 2 bits a1 and a0. B consists of 2 bits b1 and b0. The comparator has three outputs Z2, Z1, Z0. Show the logic design for this comparator using the minimum number of AND, OR, and Inverters. Verify your design using Logisim.

Design a 2-bit comparator. The comparator input has two 2-bit numbers A and B. A consists of 2 bits a1 and a0. B consists of 2 bits b1 and b0. The comparator has three outputs Z2, Z1, Z0. Show the logic design for this comparator using the minimum number of AND, OR, and Inverters. Verify your design using Logisim.

Electric Motor Control

10th Edition

ISBN:9781133702818

Author:Herman

Publisher:Herman

Chapter22: Sequence Control

Section: Chapter Questions

Problem 6SQ: Draw a symbol for a solid-state logic element AND.

See similar textbooks

Similar questions

Design the following combinational logic circuit with a four-bit input and a three-bit output. The input represents two unsigned 2-bit numbers: A1 A0 and B1 B0. The output C2 C1.C0 is the result of the integer binary division A1 A0/B1 B0 rounded down to three bits. The 3-bit output has a 2-bit unsigned whole part C2 C1 and a fraction part CO. The weight of the fraction bit CO is 21. Note the quotient should be rounded down, i.e. the division 01/11 should give the outputs 00.0 (1/3 rounded down to 0) not 00.1 (1/3 rounded up to 0.5). A result of infinity should be represented as 11.1. A minimal logic implementation is not required. (Hint: start by producing a truth table of your design).
An X-input exclusive-OR gate and a Y-input exclusive-OR gate (where X=3, Y=4 have their outputs connected to a 2-input exclusive-NORgate. Do the following:a) Draw the logic diagram and analyze the logic expression of the output (in standard SOPform).b) List out all essential prime implicants.
Electrical Engineering Task Figure shows a BCD counter that produces a four-bit output representing the BCD code for number of pulses that have been applied to the counter input. In particular, the DCBA outputs will never represent a number greater than 1001,-91, (MOD-10). (MSB) Logic BCD counter circuit HIGH only when DCBA=210-310, or 910 a. Draw the logic circuit using the minimum expression and then explain its operation. B
From the BCD code whose block diagram is given in the figure below, you can find the 7-segment LED display (with common anode) code. Solving combinational logic circuit will be designed. This type of commercially produced decoder is integrated State the features you consider important by researching the circuits. BCD input at the output of the decoder For the 0-9 values of the information information, the following display figures will be seen and the values other than these it will be considered arbitrary. Since the 7-segment LED display has a common anode, Logic "0" will be applied in response to the burned parts. The accuracy of the logic circuit you will design Create the table and find the output expressions by shrinking the table with the Karnaugh diagram method.
From the BCD code whose block diagram is given in the figure below, you can find the 7-segment LED display (with common anode) code. Solving combinational logic circuit will be designed. This type of commercially produced decoder is integrated State the features you consider important by researching the circuits. BCD input at the output of the decoder For the 0-9 values of the information information, the following indicator figures will be seen and the values other than these it will be considered arbitrary. Since the 7-segment LED display has a common anode, The logic "0" will be applied to the burned parts. Draw this circuit.
From the BCD code whose block diagram is given in the figure below, you can find the 7-segment LED display (with common anode) code. Solving combinational logic circuit will be designed. This type of commercially produced decoder is integrated State the features you consider important by researching the circuits. BCD input at the output of the decoder For the 0-9 values of the information information, the following indicator figures will be seen and the values other than these it will be considered arbitrary. Since the 7-segment LED display has a common anode, Logic "0" will be applied to the burned parts. The accuracy of the logic circuit you will design Create the table and find the output expressions by shrinking the table with the Karnaugh diagram method.
In this assignment, you are required to design a circuit that counts and displays the sequence of the number 010430011092 . The number will then be displayed on a 7-segment display and changed every 1 second. The block diagram is as shown in Figure 1. Construct your design as follow: - (a) Design a combinational logic circuit that converts binary number to a sequence of the number 010430011092 and to be displayed on a single common anode 7-segment display. The logic circuit must be designed using 2-input NAND gate
Digital logic design Solve it with drawing and simulation lab I need them both to have the full solution. And thanks Design counter that counts from 00 to 59, using the IC 74LS90 ripple counter and use two 7 segment display to display the result count. You can also use 7447 binary to 7-segment Display Decoder.
Design a combinational circuit with four input lines that represent a decimal digit in BCD and four output lines that generate the 9's complement of the input digit. Provide a fifth output that detects an error in the input BCD number. This output should be equal to logic 1 when the four inputs have one of the unused combinations of the BCD code. Provide a schematic logic diagram of it. It will surely help me in my review. Thank you so much!
answere fast please question from DIGITAL LOGIC DESIGN TOPIC : Designing Combinational Logic You are designing a water level circuit using 74ALS151 (8 to 1 Multiplexer IC)* When input is 0000 that means tank is empty.* When input is 1111 that means tank is full.* When input is below 5, that means water level is low.* So, make a circuit using 74ALS151 Multiplexer IC that shows a "low water" indicator light(by setting an output L to 1) when the water level drops below level 5.
5) You want to design an arithmetic comparison combined logic circuit.a. Write your design purpose of the 4-bit comparison (big-equal-small) circuit.b. List the process steps that you will apply in the design approach. Design a 4-bit comparison (large-equal-small) circuit. Explain each step. Realize with AND, OR, NOT gates.c. Compare the decimal numbers in the last two digits of your student number in the circuit you designed and discuss the result. last two digits of student number : 0 4 . Not : I want the solution to contain tables and equations, and the electrical circuit resulting from tables and equations, as in the picture that I attached,And if possible, Because it is normal when solving a question to have tables and equations. I want an integrated solution, please look at the question carefully before starting the solution because I have sent a question a lot
1. Design a combinational logic circuit that compares two 4-bit numbers A and B. The circuit should output the relation of the two inputs. Use an available TTL IC for the design.