dentify the States and Events for the below given requirements and create a Finite State Machine using Mealy model and tabular format? Requirement 1: User shall be able to steer the vehicle at a constant speed by setting it at an automatic mode, which can be changed to the manual mode when required. Requirement 2: User shall be able to increase speed at fixed increments till he/she reaches desired speed. Requirement 3: User shall be able to reduce speed by de-accelerating it till he/she attains the desired speed, however this function will not work when the vehicle is descending down a slope or steep road. Requirement 4: The automatic mode can be set to manual mode by starting cruise control and can set back to normal by deactivating it. The acceleration and de-acceleration increases and decreases speed. Requirement 5: In case of application of breaks the vehicle goes to manual mode from cruise control and stops the vehicle.

dentify the States and Events for the below given requirements and create a Finite State Machine using Mealy model and tabular format? Requirement 1: User shall be able to steer the vehicle at a constant speed by setting it at an automatic mode, which can be changed to the manual mode when required. Requirement 2: User shall be able to increase speed at fixed increments till he/she reaches desired speed. Requirement 3: User shall be able to reduce speed by de-accelerating it till he/she attains the desired speed, however this function will not work when the vehicle is descending down a slope or steep road. Requirement 4: The automatic mode can be set to manual mode by starting cruise control and can set back to normal by deactivating it. The acceleration and de-acceleration increases and decreases speed. Requirement 5: In case of application of breaks the vehicle goes to manual mode from cruise control and stops the vehicle.

C++ for Engineers and Scientists

4th Edition

ISBN:9781133187844

Author:Bronson, Gary J.

Publisher:Bronson, Gary J.

Chapter7: Arrays

Section7.5: Case Studies

Problem 15E

See similar textbooks

Similar questions

A factory produces two types of wood blocks with 2m and 4m lengths. The blocks are moved by a conveyor belt and passing under two photocells A and B spaced by 3m apart as shown in the following figure. The blocks are separated by more than 4m. A trap door is placed immediately to the right of photocell B. To separate the two types of blocks, it is required that the trap door should open when the small block pass under Band close when the blocks passed beyond B. The door opens when the output (2) of state machine is logic 1. The designer needs for . AND-gate(s) for implementing the aforementioned state machine (2) a d> 4m 3m 0.25m
Draw the Finite State Machine diagram for the following condition
Unless specified otherwise, use the free space propagation speed of light 3x108 m/s to calculate the propagation delay. For numerical calculations, the results must show the appropriate unit. Show a complete solution for each problem4. A digital audio broadcast service is used to transmit digital music. Stereo audio signals are to be transmitted using a digital modem over a data link. A stereo signal uses two channels. In each channel, an audio signal is sampled at a rate of 44 kilo samples/second and quantised using a 24-bit quantiser. The data link has a transmission bandwidth of 0.5 MHz. Assume a 46-byte overhead is added to each packet before transmission.a. What is the total bit rate produced by a stereo audio signal?b. What is the minimum SNR value (in dB) required for the above data link?c. Assume that the broadcast service uses the UDP/IP/Ethernet protocol to transmit digital audio, using a packet switched network. The maximum packet size is limited to 800 bytes, which includes…
Task 2The cells of the battery are treated using a programmable lathe machine. The machine has 15programs that are able to control its speed. Program 1 has 11 ( N( 1) = 11) different speeds thatcan vary from 100 revolution per minute (rev/min) to 1100 (rev/min). Program 2 has 13 ( N(2) =13) speeds that can vary from 110 rev/min to 1430 rev/min ( X1(1) = 100, X2(1)=110,and so on). The number of speeds of the higher programs increases using geometric progressionand the speeds within the same program follow the same pattern of the common differenceachieved in program 1 and 2 and increase using arithmetic progression.1. Determine the general formulas of the speeds of the programs and the number ofspeeds of the programs.2. Construct a sequence using the final speed of each program. Is there any relationbetween these speeds?3. Determine the number of speeds of program 10, and the value of speed number 7within program 10.4. Determine the total number of speeds that can be produced.5.…
A thin square metal plate has a uniform temperature of 80°C on two opposite edges, a temperature of 120°C on the third edge, and a temperature of 60°C on the remaining edge. A mathematical procedure to approximate the temperature at six uniformly spaced interior points results in the following equations: 4T₁-T₂-Th - 200 -7₁ +422-73-75 - 80 T₂ | 4T3 T4 = 140 -T3 + 4T4-T5-140 T₂ T₁ 4T5 T6 = 80 I -T₁-T₁ + 4T6 = = 200 What is the value of T1, T2, T3, T4, T5 and T6?
b. Discuss briefly with a proof how the addressable space of this computer is determine
Derivation of the Dc motor differential equations Under typical operating conditions, the torque generated by a DC motor is directly proportional to the cumrent passing through it T-kai where kis a proportionality constant determined by the characteristics of the specific motor. This relationship fails for large values of i. When the armature ratates, z generates a back electromotive force (back EMF) that opposes the applied valtage. In the circuit diagram, this is represented by a mator symbol. The voltage drop dua to the back EMF, denoted e, is proportional to the rotational velocity af the armature e-kp where k, is a constant of proportionality. Ta derive the relationship between the current i and the motor shaftt angular position 0. yau can apply KirchhofT's voltage law and Nowton's second law in terms of torques acting on the motor shaft. Kirchhoff's voltage law implies that the sum at the vatage drops across the circuit must equal tha applied voltage: iR + (1) where v is the…
25. To design analogue computer for solving the first-order system: Y(s) G(s) 0 10,0 < b ≤ 10 U(s) s+b 1. What are the possible ways of connections? 2. When it will be used for each connection?
Write a brief (a few sentences) definition and description of each of the following, and provide example(s) if helpful: (a) computational domain, (b) mesh, (c) transport equation, (d) coupled equations.
A factory produces two types of 2 points wood blocks with 2m and 4m lengths. The blocks are moved by a conveyor belt and passing under two photocells A and B spaced by 3m apart as shown in the following figure. The blocks are separated by more than 4m. A trap door is placed immediately to the right of photocell B. To separate the two types of blocks, it is required that the trap door should open when the small block pass under B and close when the blocks passed beyond B. The door opens when the output (Z) of state machine is logic 1. How many states the designer needs for drawing the minimal Mealy state diagram? * d> 4m 3m 0.25m 6. 5 4.
Provide guidance on how to establish control for a machine in a finite state.
Write, run and test a computer program to determine the equivalent force-couple system at any point for a given system of forces applied at the structure.