:Data of a linear Induction is given as follows:1.Normal supply with frequency f = 50 Hz.2.Pole pitch t = 0.6 meter.3.Primary side speed = 200 km/hr.4.Developed thrust F = 100 kilo Nw.Calculate:1.2.3.4.5.Power developed by the motor (Pm)Synchronous velocity (speed) vs.Slip (s).Input power to the secondary.Copper-loss in the secondary.

Given data Supply frequency, f=50 Hz Pole pitch, τ=0.6 m Primary side speed, vp=200 km/hr Developed…

Data of a linear Induction is given as follows: Normal supply with frequency f= 50 Hz. 1. 2. Pole pitch t= 0.6 meter. 3. Primary side speed = 200 km/hr. 4. Developed thrust F = 100 kilo Nw. Calculate : Power developed by the motor (Pm) Synchronous velocity (speed) vs. Slip (s). Input power to the secondary. Copper-loss in the secondary. 1. 2. 3. 4. 5.

Data of a linear Induction is given as follows: Normal supply with frequency f= 50 Hz. 1. 2. Pole pitch t= 0.6 meter. 3. Primary side speed = 200 km/hr. 4. Developed thrust F = 100 kilo Nw. Calculate : Power developed by the motor (Pm) Synchronous velocity (speed) vs. Slip (s). Input power to the secondary. Copper-loss in the secondary. 1. 2. 3. 4. 5.

Delmar's Standard Textbook Of Electricity

7th Edition

ISBN:9781337900348

Author:Stephen L. Herman

Publisher:Stephen L. Herman

Chapter35: Harmonics 916

Section: Chapter Questions

Problem 3RQ: Would a positive-rotating harmonic or a negative-rotating harmonic be more harmful to an induction...

See similar textbooks

Similar questions

c) Provide your recommendations for reduction of magnetic losses in an induction motor.
PROBLEM 1.1(P-1.23) A 400KW,500V ,450 rpm,6 pole DC generator is built with an armature diameter of 0.87m and core length is 0.32m. The lap wound has 660 conductors
1- To control the speed of an induction motor, the supply frequency is reduced by 10%. For the same magnetizing current to remain constant, the supply voltage must be....... a) Reduced by 10%, b) Reduced by 20%, c) Increased by 10%, d) Increased by 20% 2. When maximum starting torqua ic ohtoinod
No load test was conducted on a three phase induction motor at different input voltages and the input power obtained was plotted against the input voltage. The intersection of the extrapolated curve on the Y-axis, would give (a) rated core loss (b) windage and friction loss (c) rated copper loss (d) rated core loss and windage and friction loss
DC shunt 1200 rpm to the generator shaft. and a moment of 238.73 Nm is applied. Total iron and shunt losses are 468.75 W. Armature resistance is 0.25Ω, excitation circuit resistance is 250Ω. If the current drawn by the generator at empty load is 73.5A; a) Generator armature current (Ia =?) b) Electromotive force induced in the generator (Ea =?) c) Load peak voltage (VT =?) d) Calculate the efficiency of the generator.
A shunt DC motor is supplied by 520V terminals voltage and is used to supply a mechanical load with rotating speed of 1000rpm. The armature is wave-wound and has 500 conductors. The useful flux per pole is 0.03Wb and there are 4 poles (2 pairs of poles). The armature resistance is 0.4 Ohms. Calculate: 1.The internal emf of the motor. 2.The armature current. CLEAR AND CORRECT OR DISLIKE
A 2 pole wave wound dc shunt generator runs at a speed of 750 rpm, has an armature and shunt field resistance of 0.4 and 580 respectively. The armature has 960 conductors and flux per pole is 0.115 Weber. If the lamp load connected has a resistance of 70 determine (i) Generated EMF, (ii) Total Resistance, (iii) Armature Current, (iv) Terminal Voltage.
In DC shunt generator the type of current flows in field winding is AC whereas in armature winding it is DC. * True O False If the field winding of a DC shunt motor gets disconnected while in normal operation the speed will decrease to a tremendously low value and the motor may get stop. * True O False A DC series generator is considered suitable for general electric supply. * True False
Which of the following statements about three-phase induction motor is false (A) The speed of rotation of the magnetic field is called the synchronous speed. (B) A three-phase supply connected to the rator produces a rotation magnetic field. (C)The rotating magnetic field has a constant speed and constant magnitude. (D) It is essentially a constant speed type machine.
Q1 (a) With aid of suitable diagram, explain the losses and power-flow of an induction motor.
1. Laminations of core are generally made of. fe ST 37. 2. In case of the induction motors the torque is directly proportional to... 3. The easily method applicable to control the speed of the S.C.I.M motor is 4. The eddy current loss of ac motor is 100W at 50HZ. Its loss at 100HZ will be e0 E2
1. 2. 4. 4. •.. .... ..... .... E.g. • 2. A 3 phase, 460 V, 10hp, 60 Hz, four-pole induction machine delivers rated output power at a slip of 0.05. determine the a. Synchronous speed and motor speed b. speed of the rotating air gad field c. frequency of the rotor circuit d. Slip in rpm e. Speed of the rotor field relative to the i. rotor structure ii. Stator structure iii Stator rotating field f. haft torque of this motor at the rated load? ... .... Equivalent Circuit • The induction motor consists of a two magnetically connected systems: Stator and rotor • This is similar to a transformer that also has two magnetically connected systems: primary and secondary windings. • The induction motor is similar to the transformer with the excention that its secondarv windings are free to.