The ramp of a ship has a weight of F Ib acts in the center of gravity at G. The ramp is supportedby a pin at point "A" and a smooth surface on "B".If the ramp was in equilibrium, answer the following questions:a. Draw the free body diagram of the ramp AB.b. Determine the cable force at C that is needed to lift the ramp (that makes the reactionat B equals to Zero).c. Determine the horizontal and vertical components of reaction at pin A.Take the values of F (kN), a (deg) and X (m) from Table 1.B20Ff= 250p=270X= 6a= 55

Note:- here you gave P =270 but in question nothing is mentioned about P so, I can't include in the…

Answered: D X B 20 3 ft F

Engineering

Mechanical Engineering

D X B 20 3 ft F

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter4: Coplanar Equilibrium Analysis

Section: Chapter Questions

Problem 4.41P: The center of gravity of the 3000-lb car is at G. The car is parked on an incline with the parking...

See similar textbooks

Related questions

Q: pports the four parallel fore X kN and Fp =Y kN.

Q: Q1/ A. Write the force system for each one of the following? JIL

A: Given:- To Find:- Type of force system

Q: 4/2 /2 m O=

A: For solution refer below images.

Q: 12-x2 了了少 Je

Q: F. 15° 700 N

A: Draw the FBD for the given question and find the angle between both the forces.

Q: b. 26mm

A: the diameter of angle diffuser in flow over weirs is about 25 to 26 mm.

Q: B O2 D 3 E 201 F H at D 6 I G Needle

Q: Solve for EG, GH, and HJ

Q: A Mansard roof truss is loaded as shown. Determine the force in members GI, HI, and HJ.

A: Given data To determine the forces in the members GI,HI and HJ

Q: ion. • F = 200 F3 = 100 y = 10 • F2 = 100 x = 5 8. E

A: to find force in each member of truss

Q: A 'B 2 ft I 4 ft H. ft E G F

Q: nd the Zero member enlys 3 3. 3. D. 3. 3. 8m

A: given; find zero force member only

Q: kN/m x₂ (1) Ţ 11₁

Q: В |C O2 4 D 3 A E (201 5 F D 6 H at c I G Needle

Q: Assignment 2 E A S kN 5kN SKN A

Q: F2 2 m 2 m - 2 m

A: The force is a first order tensor that requires not only direction but also magnitude. These forces…

Q: Y U F=5 kN X 35

A: Given that, Force in the x-direction, F=5 kN,Resultant force in U-axis, R=9.5 kN, Drawing triangle…

Q: y) of the given Wide Flange

Q: FBA FBD

A: dear Student detailed answer given below

Q: Determin the moments abot A and b

A: For question number 3. Angle or slope of the 200N force is required to solve the problem. So, it is…

Q: ce Fof the triangular distributed load and its location d measured from point A.

A: Magnitude of the distributed load is calculated by calculating the area of the curve. The CG of…

Q: Draw the and B A.F.D&S.F.D& B.M.D (KN.M

A: To draw axial ,shear and bending moment diagram

Q: Q1 (25%): Resolve each force acting on the support into its x and y components. F-600 N F- S00 N

A: As per our guidelines we are supposed to answer only one question. Kindly repost other questions as…

Q: 60 150 mm B

A: The magnitude (Fd) and series of copies all of which using the x-y plane are listed below: a) Couple…

Q: What would be the resultant force Fof the triangular distributed load and its location d measured…

A: Correct answer is b.

Q: 1.6 m 1.6 2 m X- 1.5 m 0.8 m B

Q: Sind y at 2 m from the left hand 7111 سحله ولي dx

A: Concept: The integration of the load intensity is the shear force. The integration of the shear…

Q: A 2 ft F, 4 ft M B. - 3 ft- 30 -x F,

A: Given that, F1=150 lb,F2=50 lbM=500 lb.ft Consider the given frame, Resolve the given force in two…

Q: 5 ft 5 ft 12 ft 5 ft reactions in A and D

Q: 6 KN 5 kN 4 kN 4 kN 5 kN, K 3 kN 4 m 2 kN HA A G |B C |D F 2 m 2 m 2 m T 2 m T 2 m T 2 m

Q: The x component of the force F acting on point A is? (include units with answer) A. The y component…

A: From above diag coordinates areA15,0,0 B0,9,4 C0,-10,12Force F=75lb

Q: F2 = 10N F, = 50N 60° 3 F3 = 60 N

A: ∑Fx=50costan-143-F2cos60=50cos53.13-10cos60=30-25∑Fx=25 N…

Q: a. Determine the vertical reaction (kN) of the hinge. Indicate its direction, use positive value if…

Q: Tension T2 h

A: To find magnitude of tension T2

Q: =D and F13 tube shown.

A: Given data F13 = 0.17 Length of cylinder = diameter of the cylinder

Q: X -2 ft- F B 2 ft F X 2 ft

A: As per honor code and answering guidelines I can answer 1st 3 subparts at a time.If you want other…

Q: Homework: Draw S.F.Ds and B.M.Ds 12 kN/m 40 kN C A В 2 m 1m

A: As per bartleby guidelines we are allowed to solve only 1st question if multiple questions are…

Q: which of the following is/are 2-force member/members 1m 2 m 2 m H. B.

A: Objective: To find the two force members.

Q: Define the term resultant force

A: To define resultant force

Q: If gage A reads -20 kPa, determine the elevations of points L, N, Q and D.

Q: Deter.ine the internal forces at a (a+b) ft, just to the right of F1.

Q: 7 panels at 4 m B C D 4 m A H. 8 kN 8 kN

Q: Q.2) Determine Ix, Iy, and Ixy of the composite area shown below. 12 mm 12 mm 6 mm 24 mm 8 mm- 24 mm…

Q: Draw A.F.d & S.F.d & B.M.d

A: Note:As per our guidelines we are supposed to answer only one question. Kindly repost other…

Q: What would be the resultant force F of the triangular distributed load and its location of measured…

Q: with b = 2 in and h

A: Required Maximum stress

Q: y h 0.3hl

A: The given shaded is as shown below, And the centroid of the triangle OAB is given as, y¯1=23h…

Q: ᴀɴ ᴏᴘᴇɴ ᴄʏʟɪɴᴅʀɪᴄᴀʟ ᴠᴇꜱꜱᴇʟ ʜᴀᴠɪɴɢ ᴀ ʜᴇɪɢʜᴛ ᴇQᴜᴀʟ ᴛᴏ ɪᴛꜱ ᴅɪᴀᴍᴇᴛᴇʀ ɪꜱ ʜᴀʟꜰ-ꜰɪʟʟᴇᴅ ᴡɪᴛʜ ᴡᴀᴛᴇʀ ᴀɴᴅ…

Q: If gage A reads -20 kpa, determine the elevations of points L, N, Q and Z.

Q: y - 2a- 2a

A: Given shape as shown below

Question

The ramp of a ship has a weight of F Ib acts in the center of gravity at G. The ramp is supported
by a pin at point "A" and a smooth surface on "B".
If the ramp was in equilibrium, answer the following questions:
a. Draw the free body diagram of the ramp AB.
b. Determine the cable force at C that is needed to lift the ramp (that makes the reaction
at B equals to Zero).
c. Determine the horizontal and vertical components of reaction at pin A.
Take the values of F (kN), a (deg) and X (m) from Table 1.
B
20
F
f= 250
p=270
X= 6
a= 55

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

The homogeneous 20-kg door is held in the horizontal plane by a thrust hinge at O, a hinge at A, and the vertical prop BC. Determine all forces acting on the door.
The center of gravity of the nonhomogeneous bar AB is located at G. Find the angle at which the bar will be in equilibrium if it is free to slide on the frictionless cylindrical surface.
The 350-lb homogeneous plate has the shape of an isosceles triangle. The plate is supported by a thrust hinge at A, a slider hinge at B, and the cable CD. Find the force in the cable and the magnitudes of the hinge reactions.
The uniform, 20-kg bar is placed between two vertical surfaces. Assuming sufficient friction at A to support the bar, find the magnitudes of the reactions at A and B.
Find the magnitude of the pin reaction at B caused by the weight W=80lb. Neglect the weights of the members.
The 40-kghomogeneous disk is placed on a frictionless inclined surface and held in equilibrium by the horizontal force P and a couple C (C is not shown on the figure). Find P and C.
Find the smallest value of P for which the crate in the Prob. 4.34 will be in equilibrium in the position shown. (Hint: A rope can only support a tensile force.)
Two concrete blocks weighing 320 lb each form part of the retaining wall of a swimming pool. Will the blocks be in equilibrium when the pool is filled and the water exerts the line loading shown?
The 80-kg crate has its center of gravity at G. Determine the smallest force P that will initiate motion if =35.
The homogeneous bar AB weighs 25 lb. Determine the magnitudes of the forces acting on the bar at A and B. Neglect friction.
The uniform bar of weight W is held in equilibrium by the couple C0. Find C0 in terms of W, L, and .
The 40-kg homogeneous disk is resting on an inclined friction surface. (a) Compute the magnitude of the horizontal force P. (b) Could the disk be in equilibrium if the inclined surface were frictionless?