Need help steps would be helpful please and thank you! A balanced three-phase Y-Y connected crcuit has the followingcharacteristies:The phase voltage at the Source, Van, is 250 /- 40°VThe phase sequence is positive.The line impedence is Itj34The luad impedenceis29+ji7 %p.Calculate the line current, Ian. Express your answer Using pdarnotation w/anoles and degrees.(5. Calculate the phase voltage VAn, at the load in the a-phase.Owhat is the line voltacde ,VARB, at the luad?

Given:Phase voltage at the source, Van=250∠-40°Line impedance=1+j3Ω/ϕLoad impedance=29+j17Ω/ϕ

(D A balanced three-phase Y-Y connected crcult has the Aollwving characteristies: The phase voltage at the Source, Van, is 250 L-40° v The phase sequence is positive. The line impedence is itj34 The luad impedericeis 29+ji7%. @ Calculate the line current, Ian. Express yur answer using pdar notatiun w/angles and dagrees. (6 Calculate the phase voltage vAn, at the load in the aphase. Ouhat is the line voltacte , VAD, at the luad?

(D A balanced three-phase Y-Y connected crcult has the Aollwving characteristies: The phase voltage at the Source, Van, is 250 L-40° v The phase sequence is positive. The line impedence is itj34 The luad impedericeis 29+ji7%. @ Calculate the line current, Ian. Express yur answer using pdar notatiun w/angles and dagrees. (6 Calculate the phase voltage vAn, at the load in the aphase. Ouhat is the line voltacte , VAD, at the luad?

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter2: Fundamentals

Section: Chapter Questions

Problem 2.23P: A single-phase source has a terminal voltage V=1200volts and a currentI=1530, which leaves the...

See similar textbooks

Similar questions

Task 3 A three phase, four wire star connected load consisting of: ZR: a resistor of 9500 in series with a 3H inductor ZB: a resistor of 1950 ZY: a resistor of 1950 in series with a 4µF capacitor Using the equipment available in the power lab (Room T017), connect the given load to a three-phase supply available in the lab and: 3.1. Determine the current of each line and the neutral current and measure the total power supplied by the source. 3.2. Analytically, calculate all currents and the total power and compare with those obtained in measurements. 3.3. Device a method and measure the waveform of the neutral current. Discuss the obtained waveform and the reason for any distortion in the waveform 3.4. Validate your calculations using computer simulation
1) What is the phase angle between the phases in an ideal 3-phase system?
The values of the elements for the given circuit are given below.What is the maximum average power that can be transferred to the ZL load?R1 = 400 OhmsL = 500j OhmsR2 = 100 Ohms
Consider a 10 kVA, 200/400 V, 50 HZ: single-phase tranformer has the folloving test results:0.C. test: 200 V, 0.6A, 63 W (L.V.side)S.C. test : 20 V, 25A, 85 W (H.V. side)Deternine:i- The eficiengy at 75 % offiull-load at 0.9 leading power factor.ii -The secondary terminal voltage on fill-load at tunity power facton
Three load units A, B and C are connected in parallel and take currents that are respectively 12, 10 and 15 amperes. Assuming IA to be the reference phasor, IB leads IA by 30°, and IC lags IA by 65°, calculate the total current and the angle it makes with the reference.
X₂=0.1 1 XL +03 Soto X₁ = 0.2 X = 0.1 X = 0.1 Above is the one-line diagram of a simple power system. Each generator is represented by an emf behind the subtransient reactance. All impedances are expressed in per unit on a common base. All resistances and shunt capacitance are neglected. The generators are operating on no load at their rated voltage with their emfs in phase. A symmetrical fault occurs at bus 1 through a fault impedance Z, =j0.08 per unit. a) Using Thevenin's Theorem, determine the impedance to the point of fault and the fault current in per unit. b) Find the bus voltages and line currents during the fault. 2 O oto
The ACSR conductor Falcon is used in a 3-phase equidistant configuration with D = 42 feet. The per kilo feet inductive reactance will be: O A. 0.1537 B. 0.8117 O C. 0.1475 O D. 0.1148 O E. None of choices are correct
A single-phase source has a terminal voltage V=1200volts and a currentI=1530, which leaves the positive terminal of the source. Determine the real and reactive power and state whether the source is delivering or absorbing each.
The instantaneous power absorbed by the load in a single-phase ac circuit, for a general R LC load under sinusoidal-steady-state excitation. is (a) Nonzero constant (b) Zero (c) Containing double-frequency components
A single-phase, 120V(rms),60Hz source supplies power to a series R-L circuit consisting of R=10 and L=40mH. (a) Determine the power factor of the circuit and state whether it is lagging or leading. (b) Determine the real and reactive power absorbed by the load. (c) Calculate the peak magnetic energy Wint stored in the inductor by using the expression Wint=L(Irms)2 and check whether the reactive power Q=Wint is satisfied. (Note: The instantaneous magnetic energy storage fluctuates between zero and the peak energy. This energy must be sent twice each cycle to the load from the source by means of reactive power flows.)
Four conductors meet at a junction. the current are i1= 5sinwt, i2= 3sin(wt + 90) and i3= 2sin(wt-90). calculate the rms value of i4.
Three identical coils, each of resistor 2ohm and inductive reactance 6.28 ohm are connected in delta to a Supply voltage of 100V, 100 Hz, 3-phase supply, then the line current is. Select one: O a. 10.25A O b. 46.56A O c. 15.17A O d. None of these