Create a free hand oblique drawing of the three objects

Q: Given the top and front view create a section view.

A: Find Create a section view using the given top and front views.

Q: The resultant of two forces acting on the same point can be found using: * Graphical solution…

A:

Q: d the resultant and its orientation.

A: given

Q: TS DIAGRAM

A:

Q: Direction. Draw the Force Sody Diagram of he tollowing iustrations. Lund

A: Draw the free body diagram for the given figures.

Q: 2 Constraint indicated the name and where it should be

A: Given: To find: Where the constraint should be

Q: Given the two views of an object, draw the missing view and an isometric of the оbject

A: According to the details provided in the question, we need to draw an orthographic projection as…

Q: Problem 3. a. A force has a magnitude of 1 kN and coordinate direction angles of 0,= 60°, 8, = 120°,…

A:

Q: Do the auxiliary view of this drawing

A: According to the details provided in the question, we need to calculate the auxiliary view. the…

Q: Need auxiliary views of this drawing

A: This question is based on the concept of engineering drawing.

Q: For the given isometric drawings, draw the corresponding top, front, and right side views

A: Note: As per policy, we can solve the first question from the multiple questions. Please resubmit…

Q: Locate and draw the INSTANT CENTERS ( Known and unknown )

A: Locate and draw the INSTANT CENTERS ( Known and unknown )

Q: Identify the following sectioning views (a, b, and c). a O Removed, Revolved and Removed O All…

A:

Q: Draw the three projection in sheet

A: Orthographic Projection It is a form of presenting a three-dimensional object into Two dimensional.…

Q: Given the front, top and side views of the drawing add the missing lines (center, object, and…

A:

Q: Figure 2 shows Lela pulling her wagon towards Teluk Nipah beach. In order to reach the beach, she…

A: Given: The initial position of Lela along x-axis, xo =0 The initial position of Lela along y-axis,…

Q: RIS R12 frant sew R32

A: Given 3D model To find Three views

Q: 4 A Moving to another question will save this response. Question 19 Point O (0, 0) is the fixed…

A:

Q: What is the Neutral Axis?

A: The neutral axis is the fiber of the beam with no normal stress. When a beam is subjected to a…

Q: Use basic drawing instruments (pencil, scale, protractor, compass, etc). A hexagonal prism with side…

A: In the below figure, we can see on the right-hand side the development of sectioned hexagonal prism.…

Q: ths angle of the three forse acting on hook

A: given: determine the resultant and the angle of the three forces acting on hook?

Q: Draw front, top and then left side view.

A:

Q: The positive and negative directions for the X and Y-axes on the mill are determined by the…

A: The mill axis which moves left and right is the x-axis for both vertical and horizontal spindle…

Q: Q1: Consider the points A, B, C, D where coordinates are respectively (1,1,0), (-1,1,0), 0,-1,1).…

A: According to the given  information solution is given below…

Q: QUESTION 2. Below are 4 sets of images. Each shows the front and top views of an object along with 4…

A: Givensets of mages as shown below

Q: Given the Isometric views, draw the three orthographic views below

A: Orthographic views of the given isometric view are drawn on the grid paper. 1 Grid = 1 unit.

Q: On the first picture, you have the length of the triangle as 300. If the total length of the door is…

A: Here you are asking why the length of the triangle is 300 and not 440.

Q: PLease draw the top view and section view with dimension of the figure

A: Here is Top View and Section View of figure with well dimensioned.

Q: The rear window of an automobile is defogged by passing warm air over its inner surface. If the warm…

A:

Q: Problem 3: Note: Make sure to draw all diagrams. All Units must be included. Determine the magnitude…

A:

Q: Given vector G = -3a, - 8a, + a, determine the ff: a. Drawing of the vector G b. Magnitude of vector…

A: Given vector G = -3ax⇀ -8ay⇀+az⇀⇒Components along x , y and z for G are -3 , -8 and 1 respectively

Q: What is a Couple Moment?

A:

Q: Find the missing coordinate of P, using the fact that P lies on the unit circle in the given…

A: P(x,1/3)          ..........(1) To find the value of x  The given quadrant is IInd (-ve,+ve) The…

Q: Sketch the OBLIQUE drawings based on the ORTHOGRAPHIC views.

A: Given :

Engineering Drawing

Technical drawing has been around since ancient times. As in the ancient Renaissance, complicated drawings were created, including Leonardo da Vinci's drawing. Modern engineering drawing, including its specific orthographic projection with scale conventions, began in Europe (France) during the early stages of Industrialization. L.T. C. Rolt also made some of Marc's drawings for its block-making machinery (in 1799) that also may have contributed significantly to British engineering technology. Since he learned the art of presenting three-dimensional(3D) items in a two-dimensional(2D) plane, as we now term mechanical drawing.