COP of 3.8 and uses 200 W

Q: Use water as a drilling mud to drill a well to a depth of 3000 feet , calculate the pressure…

A: This question is based on pressure gradient. The data given are: Depth = 3000 feet

Q: ind modulus of elasticity of a brass rod of length 200 mm which is subjected to a tensile stress of…

A:

Q: An oil burner nozzle is labeled 60°. This is the angle from straight ahead tothe direction that the…

A: Paper is placed 12 inches from the nozzle.  the oil burner is labeled at 600C, The Schematic of the…

Q: What is the formula for crushing efficiency, given specific surface area of a product, mass…

A:

Q: 7. Determine the number of sprinkler heads required to protect an inside process area of 2000 ft².…

A:

Q: A square polymer sample of edge length 80 mm is subjected to a force of 6400 N. The resulting stress…

A: Given data: Length of edge of a square = 80 mm Force = 6400 N

Q: 16. What is the unit of resistance in SI? O w O W/K O m-K/W O W/m^2-K O K/W

A: Asked;  SI unit of resistance

Q: A 2 mm diameter glass tube is inserted into an open glass of water (contact angle between the tube…

A: Diameter of glass tube =  2 mmContact angle,  = 0

Q: It is said that inlet gas takes 5-6 turns in Cyclone Separator.Justify the statement.

A:

Q: A B Rate of deformation, duldy Shear stress, 7

A: There are several properties defined for fluid such as density, specific gravity, viscosity, etc. In…

Q: In general, why should the operating pressure be high and the operating temperature be low for an…

A: The reason for the high pressure and low temperature for the absorption process is to be mentioned…

Q: A machine rotates at 8800 rpm and decelerates at 95 rad s^-2 . Find how long it takes the machine to…

A: The objective of the question is to find out the time it takes for the machine to stop from its…

Q: For multicomponent distillation,under what conditions is the pinch point located at the…

A: The condition at which pinch point is located at the location of feed is to be mentioned.

Q: A valve chokes refrigerant 134a from 0.7 mPa to 160 kpa. Determine the temperature released by the…

A:

Q: drag force

A:

Q: Why do positive displacement pumps cause pose more overpressure hazard compared with centrifugal…

A: In a positive displacement (PD) pump, a fixed volume of liquid is trapped inside an enclosed chamber…

Q: Cone has top and bottom diameters of 10 and 20 cm and a height of 10 cm. Calculate the shape factor…

A:

Q: 10 - 10 -10 10 120 10 10 50 80 10 160

A: distance H from the bottom of the base plate  i.e. y co-ordinate of the centroid we have to…

Q: Sketch the principle of a hydraulic press.

A: Hello. Since you have posted multiple questions and not specified which question needs to be solved,…

Q: Convert a viscosity of 20 (g)/(cm)(s) to the American Engineering units (Ibr)(hr)/(ft?)

A: Given viscosity is 20 g/cm s Viscosity unit of g/cm s have to convert into American Engineering unit…

Q: What is a  vane-axial cyclone seperator?

A: This question is from cyclone separators which form an important part in separation processes. The…

Q: A centrifuge bowl is spinning at a constant speed of 2000 rpm. The radius of bowl in cm needed to…

A: Given that N =2000 rpmwe have to find radius of bowl in cm when there is needed to create a force of…

Q: 3. Define the hydraulic and energy grade lines, and explain the method of calculating and drawing…

A: It is asked to define the Hydraulic grade line and energy grade line  and explain the method of…

Q: What is a flexible wedge gate used for

A:

Q: Why does the fluid drop in the fluid level measurement experiment when the pump is turned off?

A: In a typical fluid level measurement experiment, the pump is used to recirculate the fluid in a…

Q: Q.3 a). A tensile stress is to be applied along the long axis of a cylindrical brass rod that has a…

A: The magnitude of load is to be calculated.

Q: pipe, g/cm', and the melt has a dynamic viscosity of 3.12 g

A: 1. diameter= 10cm = 10*10-2m 2. Density = 7.8 g/cm3= 7800 kg/m3 3. dynamic viscosity= 3.12g/ms=…

Q: Liquid Properties a. Define (note: your definition must be based on the closed conduits/pipe flow):…

A: The definitions of all the terms are written below:

Q: If the entering velocity is 6 m/s, calculate the length of tube and determine whether the process is…

A:

Q: 2. List the most important pipe friction formula.

A: Introduction: The friction loss in uniform, instantly sections of pipe, called "major loss", is…

Q: Using a flow chart, show how a lubricant oil with high viscosity index can be manufactured from…

A: In petroleum industries, Crude oil is a type of fossil fuel that is a naturally occurring petroleum…

Q: Q1) Air at 34°C temperature and (no) m/s velocity passes across a 2m flat plate length and Im depth.…

A:

Q: 5. Absolute pressure is measured relative to atmosphere. Tor F

A: Absolute pressure is measured relative to a full vacuum Whereas the pressure that is measured…

Q: How is pump impeller size calculated

A: The two industrially used pumps are: Positive displacement (PD) pump and Centrifugal pumps. In a…

Q: In a gyratory crusher the size reduction is effected primarily by: 1.impact 2.attrition 3.cutting…

A: This question is based on crushing and grinding operations. We will analyse each option and find the…

Q: What is the maximum radial distance traveled by any particle in cyclone seperator?

A: Chemical processes consist of the separation stages in which the process streams are separated and…

Q: The following are not commonly made from composites: Select one: a. Desks b. Canoes c. Bridges d.…

A: Ans.  Composites is the material that are made up of two or more materials. Which on combining they…

Q: Cl the dimensions were all the same, which chocolate can withstand the greatest load? D. Which has…

A: C. The chocolate that can withstand the greatest load is to be mentioned.

Q: Write about momentum transfer

A: Details about momentum transfer. Momentum transfer is a very useful concept in fluid mechanics.

Q: A system asshown in the figure is used to measure accurately the pressure changes when pressure is…

A:

Q: 1. Calculate the surface per unit volume in square centi- meters per cubic centimeter of galena…

A: Mesh%…

Q: Derive the three laws of crushing from fundamental equation

A: