Convert the logic diagram below to both NAND and NOR implementations. B D 거 E
Q: (/Find the current through the 10 ohms resistor by Maxwell theorem? t 30.03 100 150 60 V
A: In this question, We need to determine the current in the 10 ohm resistance as shown the circuit.…
Q: (a) Figure 1(a) is a sinusoidal oscillator. Given that the feedback factor is: R³ B= 1 5R R³+j²C²²C²…
A: Since you have posted the question with multiple subparts, we will solve the first three subparts…
Q: Q3/ For the circuit shown find (a) Equations for 1₁ and 1₂ with respect to V₂ (b) The value of V₂/Vs…
A: It is given that:
Q: (B) The output response for a second order system (RLC circuit) is given in Fig.(1) below. If the…
A:
Q: A 3-Phase 10Kva, 400 V, 50Hz star connected alternator supplies a rated load at 0.8 power factor…
A:
Q: A coil that consists of 450 windings is wound around a Bakelite ring. The mean diameter of the ring…
A: Coil: A coil is made by connecting a few curves in a series. Coils are used as components of…
Q: Q1) For the two-port network shown in Figure (1) below, obtain the Y-Parameters and state whether…
A:
Q: 2) For the bi-stable multivibrator circuit using BJT transistors, if the trigger waveform frequency…
A: Given here a question about bi-stable Multi vibrator. Given triggering wave form frequency and asked…
Q: An AM radio station using double side band transmitted carrier system employs a carrier of frequency…
A: An AM radio station using double side band transmitted carrier system.Carrier frequency :fc =2.1…
Q: neutral? What are the minimum allowable ampacities of the phase conductors and the neutral conductor…
A: Neutral conductor is the intermediate conductor of the three phase wire system it is usually…
Q: A digital communication system uses a repetition code for channel encoding/decoding. During…
A: From the question, it is given thatCrossover probability P=0.1We know that probability of error…
Q: A 10 V, 1.5 kHz AC voltage source is connected to a series RC circuit where R=2.2kΩ & C=0.02 μF. a.…
A: In this question, We need to draw the phasor domain of the circuit, impedance diagram and phasor…
Q: a 0.9062 Cos (1-√3x) dx = 1/2 -0-1 a=0.5968 How?
A: The substitution method is one of the method to solve the integrals. In this method, we substitute…
Q: The base current amplification factor B is given by Select one: a. lE/B b. lc/B C. IB/E d. All of…
A: Given: The base current amplification factor β is given by ______.
Q: LXI H 3140 is O Register Addressing Mode O Direct Addressing Mode O Implicit Addressing Mode O…
A: It is the various methods that a microprocessor uses to access data. The programmer must include the…
Q: A three-phase transmission line is designed to deliver 190.5 MVA at 220 kV over a distance of 63…
A: Dear student as per our guidelines we are supposed to solve only one question in which it should…
Q: An AM radio station using double side band transmitted carrier system employs a carrier of frequency…
A: Given fc = 2.1MHz fm = 4kHz = 0.004MHz
Q: If vi(t) is a step voltage in the network shown find the value of the resistor such that a 25%…
A:
Q: Q3. Find the values of controller gain Ke that make the following feedback control system stable.…
A: Feedback control system: In this system, the feedback path is faded from the output to the input of…
Q: 2. We know, the equation of Frequency Modulated signal, s(t) can be described as: s(t) = cos[wet +…
A: a st = cosωct+∆ω∫0tmtdtmt=tso , ∫0tmtdt = t22s(t) = cos[ωct+∆ω×t22](b)∆ω=8 ; fc=10 Hz ; fm=1 ;…
Q: 10V, 1kHz signal is applied to a 10mH coil with negligible winding resistance. Determine Q (Reactive…
A: We need to find reactive power for given circuit
Q: 03: (A): Using Routh's criterion, determine the stability of the closed-loop system that has the…
A: Given data, The characteristic equation is:- S4+2S3+10S2+20S+5=0
Q: Question: What would the pole pass frequency be for a AC induction moor running at 878 RPM? ( assume…
A:
Q: 2. Obtain the equivalent resistance Rab in circuit of figure below which all resistors have a value…
A:
Q: : A lossless T-junction power divider has a source im racteristic impedances so that the output…
A:
Q: 392 www 12 V 1 mH moo iz(t) 2010 + t=0 R592 vc(t)=1mF The switch in the Figure above is opened for a…
A:
Q: / In the circuit of Fig (2) R=480 02, L-0.4H, C=2.5 µF and Vs=120V A. Calculate the characteristic…
A:
Q: (A) Consider the following system, Draw the Polar Plot for the open loop Transfer Function 100 G(s)…
A:
Q: Q1/ Determine the Mesh Currents (1₁ and 1₂) for the circuit shown below
A:
Q: 46. In PNP BJT, .......current is highest current. O a. Base. b. Collector. O c. Source. O d. Drain.…
A: We need to select correct option for bjt current
Q: A solenoid coil has a resistance of 30 Ohms and an inductance of 0.5H. If the current flowing…
A: In this question, We need to determine the voltage V and phase difference between voltage and…
Q: (a) Describe in diagrams the practical Analog filter specifications. (b) Explain the design process…
A: Given The practical Analog filter specifications and the design process of digital filters are…
Q: A common emitter transistor amplifier working in active mode of operation has collector current of 1…
A: Given: A common emitter transistor amplifier working in active mode has, Collector current, IC=1 mA…
Q: 5a) Calculate the intrinsic carrier concentration for GaAs at 40°C. (For GaAs, the band gap is…
A: a By formula of interinsic carrier concentration ni = Nc×Nv×e-Eg2KTHere , K = 1.38×'10-23…
Q: State the types of induction motor
A: Types of induction motor
Q: (a) A system consists of two components that can be presented by the respective h₁ (t) =…
A: GIVEN: h1(t)=3000e-20th2(t)=t e-10tu(t) input voltage of the system…
Q: Q1/B/ Sketch the design flow chart for the cooling power electronics microchips.
A: Cooling power electronics microchips : Cooling power electronics microchip is a device which is used…
Q: 3/ Determine the node voltages, Va and Vb, for the circuit of Figure by Nodal analysis method? 3 A…
A: We need to find out the node voltage for given circuit
Q: Q1: Obtain the state space representation of the electrical network shown in Fig. 1, below. use…
A: Given circuit is
Q: Consider the circuit in Fig. 16.12(a). Find the value of the voltage across the capacitor assuming…
A: Given that Vst=10 utinitial current through inductor i0=-1Ainitial voltage across capacitor…
Q: 3. Find the total inductance Lab for the given network below. a o 6 mH m 8 mH bo m 10 mH 8 mH 6 mH 5…
A: We will find out equivalent induct
Q: Problem: A certain full-wave rectifier has a peak output voltage of 30 V. A 50 μF capacitor-input…
A: In this question, We need to determine the peak to peak ripple voltage and dc output voltage? Peak…
Q: 2 . Why is copper mainly used in electrical cables and electronic industries
A: Electric conductors used in cables and electronic industries should have low resistivity. If…
Q: ( 2 Find the total resistance between the point A and B of the flowing figure(a)? 402 A-W- A D Lim
A:
Q: Apply Norton theorem to calculate the current in 6 2 resistance for the circuit in figure 3 2001 +…
A: Given here a electrical circuit and asked to find the current through the 6 ohm resistor by using…
Q: Given m = 17, determine V3. 5-8 1 V₁ 2 10 0 V₂ 2 13 0 Loo 4][V₂] [m 3
A: Given data, 5-812100004V1V2V3=130m m=17
Q: Find the power relations (real power, reactive power, apparent power, draw power triangle)
A:
Q: Inverse Laplace Transformation: Find 2¹7 s² +9s+2 2 (s − 1)²(s + 3) - -].
A:
Q: Consider the circuit in Fig. 16.12(a). Find the value of the voltage across the capacitor assuming…
A: here only one independent source so we can't apply the superposition theorem. According to…
Q: (b) Figure 2(b) shows a filter circuit. Answer the following question based on this circuit. (i)…
A: Filter:- It is a circuit that passes specified range of frequencies and attenuates unwanted…
Step by step
Solved in 6 steps with 5 images
- Below is an example of an NMOS logic circuit. For all of the MOSFETs in the circuit below, assume V = 1 V and k = 50 mA/V². th R₂ = 5600 R₁ = 4700 M3 Ao M₁ M₂ a. Indicate and verify the state of each MOSFET and V for the following input 0 combinations. Fill-out the table below for each assumed state of the MOSFET for every input combination. Use R approximation for linear operation and three significant ds(on) figures for the voltages. Example: M1 is assumed to be in saturation. If Vgs = 2 V, Vds = 4V, Vds > Vgs - Vth 4>2-1 4> 1 (ok) Vgs > Vth (2>1) A B M1 state M2 state M3 state V OV OV 5 V OV b. What kind of logic circuit is implemented in the circuit above? 5V www. V₂ 05. Design a two-level NAND-gate logic circuit from the follow timing diagram B %3D D FQ#01: The schematic shown in figure below is for Divide_by_11, a frequency divider, that divides clk by 11 and asserts its output for one cycle. The unit consists of a chain toggle-type flip-flops with additional logic to form an output pulse every 11th pulse of clk. The asynchronous signal rst is active-low and drives Q to 1. Develop and verify a model of Divide_by_11. Vcc 20LSB Q2 03MSB clk clk clk clk clk rst rst rst rst wl w2 clk QB cik_by_11 rst rst
- i) Construct a CMOS NAND gate, NMOS NAND gate and NMOS NOR gate. ii) What are the differences between Resistor Transistor Logic, Directly Coupled Transistor Logic and Transistor Transistor Logic? Draw 3 input NAND using RTL, 4 input NAND using DCTL. iii) A certain gate draws 3mA when its output is HIGH and its average power dissipation, Vcc is 7V for Transistor Transistor Logic. How much does the gate draw when its output is LOW? It draws 4.5 mA when in Transition time. Determine average power dissipation for CMOS. iv) Determine if the LSTTL (5V) can drive a CMOS (5V, HCT) circuit and vice ve sa. Voh Vol Vih Vil LSTTL 2.8 0.38 1.9 0.9 CMOS 2.3 0.75 2.85 0.751.1 Given the timing diagram for 3-bit input A and two outputs, S and C in Figure la, where A2 is the MSB and Ao is the LSB. Assume the output for the other input conditions is don't cares (i.c. X). Determine the minimum logic circuit using NAND logic configuration. Az Ac S C Figure laThe following digital IC is: TTL AND gate OTTL NOT gate CMOS NAND gate TTL NAND gate OCMOS AND gate SN 7400N 7645
- An inverter circuit is shown below Vin Voo M₂ •Vout =a) if Vin = 01001110 in what is Vout (11) Draw the wave form of Vin and Vout.Design counter that counts from 00 to 59, using the IC 74LS90 ripple counter and use two 7 segment display to display the result count. You can also use 7447 binary to 7-segment Display Decoder shown below.a) Design a single-digit decade counter that counts from 0 to 9 and repeats. The single-digit decade counter should be built by a cascaded synchronous binary counter (74LS163) and other basic logic gates. Simulate the complete counter circuit by OrCAD and PSPICE. Capture the circuit schematic and the simulated waveform. (Define the simulation timings for at least one full counting cycle from 0 to 9 and back to 0.) (Hint: Use the DigClock input from the SOURCE as shown below and setup the CLK ONTIME and OFFTIME accordingly for the clock source.) 1/6 Pat DigClock Part List OFFTIME = SuS DSTM1 ONTIME = DELAY= STARTVAL = 0 OPPVAL = 1 Sus EUK FleStim AC Lbrajes Design Cache b) Read the specification of 74LS47 (BCD-to-7-Segment Decoder shown in Appendix) to see how the logic IC operates to drive a 7-segment LED display. Draw the circuit connection of the decade counter in (a) and the decoder to display the count value on the 7-segment LED display. Further explain why common anode…
- Q1) Design a digital circuit that performs the four logic operations of NAND, NOR, exclusive-OR and exclusive-NOR. Use two selection variables. Show the logic diagram of one typical stage.Parallel resonant inverters are mostly known for the following features: Select one: O a. None of these O b. The output current is dependent from the load. O c. The resonant circuit, load and switch are all in parallels O d. It has the advantage of requiring small reactive components Consider a full-bridge resonant inverter. The switching sequence of the devices is Select one: O a. Q1D1, Q2D1, Q3D4, Q4D3 O b. Q1D1, Q2D2, Q3D3, Q4D4 O c. Q1Q2, D3D4, Q3Q4, D1D2 O d. Q1Q2, D1D2, Q3Q4, D3D4 The gating technique using a train of pulses is suitable for: Select one: O a. Resistive and inductive loads O b. Resistive loads O c. Inductive loads O d. None of thesei) Solve Vo for each of the circuits shown below. Assume that Vtn = |Vtpl = 0.5V, that there is no subthreshold cond oV 2.5V OV 2.5V Vo 2.5V. 2.5V %3D Construct the function F = ac'd'+acd+a'cb´+a'c'b using PMOS Pass Transistor Logic