converging-diverging nozzle is always identical with the exit pressure for, No p* is found p* takes place at throat section.

Q: 2. Explain in short major engineering difficulties in water treatment process

A: This question is based on water treatment process and the engineering difficulties associated with…

Q: 2) Describe the different types of fluids and illustrate them on a graph of shear stress vs du/dy.…

A:

Q: the equivalent length of the exchanger as a complete unit (in terms of 20 mm diameter tube).

A: Consider a heat exchanger of length 12m, 10 close return bends and 15 x 90° elbows connected in…

Q: An oil burner nozzle is labeled 60°. This is the angle from straight ahead tothe direction that the…

A: Paper is placed 12 inches from the nozzle.  the oil burner is labeled at 600C, The Schematic of the…

Q: 7. Determine the number of sprinkler heads required to protect an inside process area of 2000 ft².…

A:

Q: 16. What is the unit of resistance in SI? O w O W/K O m-K/W O W/m^2-K O K/W

A: Asked;  SI unit of resistance

Q: It is said that inlet gas takes 5-6 turns in Cyclone Separator.Justify the statement.

A:

Q: In general, why should the operating pressure be high and the operating temperature be low for an…

A: The reason for the high pressure and low temperature for the absorption process is to be mentioned…

Q: For multicomponent distillation,under what conditions is the pinch point located at the…

A: The condition at which pinch point is located at the location of feed is to be mentioned.

Q: Fraction of water

A: To Answer whether the fraction of water in the underflow stream of thickener is zero

Q: Why do positive displacement pumps cause pose more overpressure hazard compared with centrifugal…

A: In a positive displacement (PD) pump, a fixed volume of liquid is trapped inside an enclosed chamber…

Q: Cone has top and bottom diameters of 10 and 20 cm and a height of 10 cm. Calculate the shape factor…

A:

Q: 4. Draw the (211) plane on a standard set of x,y,z coordinates.

A: To visualize the (211) plane in a standard set of x, y, z coordinates, we can represent it as a 2D…

Q: The reaction CH4 + C3H8 → 2C2H6 is very fast and reaches thermodynamic equilibrium in the reactor.…

A: Hello ! Since your question has multiple sub-parts , we are answering the first three .Please repost…

Q: Sketch the principle of a hydraulic press.

A: Hello. Since you have posted multiple questions and not specified which question needs to be solved,…

Q: The purpose of maintaining vacuum in evaporator is to O a. Reduce in concentration O b. Reduce in…

A: Evaporation is a heat transfer process and evaporators are used to concentrate different types of…

Q: Why does the fluid drop in the fluid level measurement experiment when the pump is turned off?

A: In a typical fluid level measurement experiment, the pump is used to recirculate the fluid in a…

Q: Which is correct for the figure ? below System Square edge pipe entrance 90° elbow 50 ft Globe valve…

A: According to the diagram, there are only one Valves which is Globe valve (Fully Open), Therefore,…

Q: Viscosity varies with temperature according to which of the graphs below?

A: How does viscosity vary with temperature?

Q: Thermocouple

A:

Q: 8. What type(s) of corrosion occur when metal is subjected to a high- velocity fluid flow with…

A: A) this option is not correct because it is the most general type of corrosion and is caused…

Q: What is fluid power requirement of a cyclone seperator and how is it calculated?

A: A cyclone separator is used to separate the solid dust particles and the particulate matter from the…

Q: What is Outlet Gas Velocity in a cyclone seperator?

A: In mechanical operation, Cyclone separators are separation devices that use the principle of inertia…

Q: Liquid Properties a. Define (note: your definition must be based on the closed conduits/pipe flow):…

A: The definitions of all the terms are written below:

Q: If the entering velocity is 6 m/s, calculate the length of tube and determine whether the process is…

A:

Q: 25- Horizontal wells require

A: Horizontal wells: It is the technique in which oil or gas well is dug at angle at least 8 degrees to…

Q: What problem could arise in the turbine given a certain quality at the exit?

A: The problem that can arise in a turbine with certain quality at the exit is to be mentioned.

Q: The power output of a wind turbine increases with the following EXCEPT:

A: the power output of the turbine increases with the following except. Select suitable currect option

Q: 1. Calculate the value for 2.303 RT/F at 50°C.

A: Disclaimer: Since you have asked multiple question, we will solve the first question for you. If you…

Q: 1. Determine the maximum allowable vacuum that can be applied to a low-carbon-steel cylindrical…

A: Since you have asked multiple questions, we will solve the first question for you. If you want any…

Q: 5. Absolute pressure is measured relative to atmosphere. Tor F

A: Absolute pressure is measured relative to a full vacuum Whereas the pressure that is measured…

Q: 23. Show that in the limit of infinite dilution, the reduced viscosity and inherent viscosity are…

A: Reduced viscosity is defined as the ratio of specific viscosity to the concentration of the…

Q: (b) The general characteristics of three oil wells selected for artificial lift as production method…

A: Table of 3 well are given.

Q: How is pump impeller size calculated

A: The two industrially used pumps are: Positive displacement (PD) pump and Centrifugal pumps. In a…

Q: Compute the capillary rise in mm of pure water at 10 Celsius expected in an 0.8 mm diameter tube.

A:

Q: Compare S.I and C.I engines with respect to fuel used

A: CI engine - Compression ignition engine SI engine - spark ignition engine

Q: Define about Dipole Moment ?

A: The dipole moment is to be defined.

Q: A system asshown in the figure is used to measure accurately the pressure changes when pressure is…

A:

Q: 5. Rods AC and BC are used to suspend the 200-kg load. If each rod is made of a material for which…

A: