consider two shafts in torsion, each of the same material, length, and cross-see tional area. Oneshatt has a solid Square cross sec tion and the other shaft has a solid circular see tion. (a) which shaft has the greater makimum shear striss and by wwat pereentage? (b) which shaft has the greater angular twist 0 and bg what pereentage?

consider two shafts in torsion, each of the same material, length, and cross-see tional area. Oneshatt has a solid Square cross sec tion and the other shaft has a solid circular see tion. (a) which shaft has the greater makimum shear striss and by wwat pereentage? (b) which shaft has the greater angular twist 0 and bg what pereentage?

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter3: Torsion

Section: Chapter Questions

Problem 3.12.3P: A full quarter-circular fillet is used at the shoulder of a stepped shaft having diameter D2= 1.0...

See similar textbooks

Similar questions

A shaft with a solid, circular cross section consisting of two segments isshown in parta of the figure. The left-hand segment has a diameter of 80mm and length of 1.2 m; the right-hand segment has a diameter of 60mm and length of 0,9 m.Shown in part b of the figure is a hollow shaft made of the same materialand having the same length. The thickness tof the hollow shaft is d/10,where dis the outer diameter. Both shafts are subjected to the sametorque.a. If the hollow shaft is to have the same torsional stiffness as thesolid shaft, what should be its outer diameter d?b. If torque T is applied at either end of both shafts and the hollowshaft is to have the same maximum shear stress as the solid shaft,what should be its outer diameter d?
A hollow steel shaft transmits 600 kW at 500 rpm. The maximum shear stress is 62.4 MPa. Find the outside and inside diameter of the shaft, if the outer diameter is twice of inside diameter, assuming that the maximum torque is 20% greater than the mean torque The answer is 100mm and 50 mm. can you help me this calculation and i give the answer already. and write with pen. tqvm
The propeller shaft of a large ship has anoutside diameter 18 in. and inside diameter 12 in., asshown in the figure. The shaft is rated for a maximumshear stress of 4500 psi.(a) If the shaft is turning at 100 rpm, what is themaximum horsepower that can be transmittedwithout exceeding the allowable stress?(b) If the rotational speed of the shaft is doubledbut the power requirements remain unchanged,what happens to the shear stress in the shaft?
A turning force of 4 kN parallel to the "y" axis will be applied at the C point of the arm connected to the steel shaft AB in the figure. Accordingly, find the safe diameter value of the AB shaft using TRESCA and VON-MISES criteria.
The steel shaft of a socket wrench has adiameter of 8.0 mm and a length of 200 mm (seefigure).If the allowable stress in shear is 60 MPa, whatis the maximum permissible torque Tmax that may beexerted with the wrench?Through what angle f (in degrees) will the shafttwist under the action of the maximum torque?(Assume G = 78 GPa and disregard any bending ofthe shaft.)
A solid steel shaft, 90 mm in diameter is coupled in series to a hollow shaft withan external diameter of 100 mm and internal diameter of 90 mm. Calculate thetorsional stiffness of 1 mm length of each of these shafts if they are usedseparately and compare this with the torsional stiffness of a 1 m length of thecompound shaft consisting of a 0.5 m length of each of the shafts mentionedabove. (G = 80 GPa)
A solid 11 mm diameter shaft is subjected to an axial load of P- 33 kN and a torque of Tacting as shown. If the largest shear stress in the shaft must be limited to 201 MPa, what is the largest torque Tthat can be applied to the shaft? (1) Part 1 Calculate the cross-sectional area and the polar moment of inertia for the shaft. Answer: A = mm2 J= mm4
The maximum torsional shear stress of a shaft with diameter D can be found at what distance from the center of the shaft?
A pipe with an outside diameter of 4.0 in. and an inside diameter of 3.624 in, is subjected to an axial force of P-850 lb, a horizontal force of Pz 1560 lb, and a concentrated torque of T-2940 lb-in, acting in the directions shown. Assume a 49 in. Section propertles for the pipe are A-2.2514 in.?,J-8.199 in.", and ly 1-4.0995 in.. Determine the normal and shear stresses at point K, and show these stresses on a stress element Answer: Oy = psi Txy psi
A copper tube with circular cross sectionhas length L 5 1.25 m, thickness t 5 2 mm, andshear modulus of elasticity G 5 45 GPa. The bar isdesigned to carry a 300 N m? torque acting at theends. If the allowable shear stress is 25 MPa and theallowable angle of twist between the ends is 2.58, whatis the minimum required outer diameter d?
A full quarter-circular fillet is used at the shoulder of a stepped shaft having diameter D2= 1.0 in. (see figure), A torque T = 500 lb-in. acts on the shaft. Determine the shear stress at the stress concentration for values as follows: D1= 0.7,0.8, and 0.9 in. Plot a graph showing versus D?
A stepped shaft ABC consisting of two solid, circular segments is subjected to torques T}and T2acting in opposite directions, as shown in the figure. The larger segment of the shaft has a diameter of dv- 2.25 in. and a length Lt= 30 in.; the smaller segment has a diameter d2— 1.75 in. and a length L, = 20 in. The torques are T, = 21,000 lb-in. and fz=10.000 lb-in. (a) Find reaction torque TAat support A. (b) Find the internal torque T(x) at two locations: x = L1/2 and x = L1+ L2/2. Show these internal torques on properly drawn free-body diagrams (FBDs).