Consider three cast iron pipes in parallel with the following dimensions: Pipe Length [m] Diameter [cm] 1 800 12 600 8 3 900 10 The total water flow rate is 200 m³ /h at 20°C. Determine the flow rate in each pipe and the pressure drop across the system.

Consider three cast iron pipes in parallel with the following dimensions: Pipe Length [m] Diameter [cm] 1 800 12 600 8 3 900 10 The total water flow rate is 200 m³ /h at 20°C. Determine the flow rate in each pipe and the pressure drop across the system.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The figure shown below is a series pipeline system used to draw a fluid from a lower source open tank to a higher destination open tank . The flow and geometric layout for the system are listed below: Fluid: water Volume flow rate: Q=0.015 m3/s Elevation difference: h=8.0m of two free surfaces Suction line: DN100 Sch. 40 Steel pipe Length: Ls=2.0 m Valve1: hinged disc type foot valve Entrance type: well-rounded Discharge line: DN80 Sch. 40 Steel pipe Length: Ld=100 m Valve2: full open gate valve Elbows: 90ο long radius elbow (1) Select the simplified general energy equations for section 1 and 2_________ A. B. C. D.
Engine oil at 40 C [density 876 kg/m^3, viscosity 0.2177 kg/m.s] flows in a 22-cm-diameter pipe at a velocity of 1.1 m/s. The pressure drop (in Pa) of oil for a pipe length of 24 m is ?
The pressure drops 4P = P₁ P2 through a long section of round pipe can be written in terms of the shear stress Tw along the wall. Shown in Figure 3 is the shear stress acting by the wall on the fluid. The shaded region is a control volume composed of the fluid in the pipe between axial locations 1 and 2. Using the method of repeating variables, generate a relationship for pressure drop as a function of all other parameters Final ans AP = P μ (₁ AP= {(₂17₂) P₁ CV UPL м = (²1 ²² an! VPL O P.H. L V
A horizontal jet of water 30 mm diameter is impinging on a vertical fixed plate. If the force exerted by the jet is 282.5 N, find the velocity of the jet. [Ans. 20 m/s]
Prob4 Flowing Liquid: Water; Pipe length: L=600 m; Diameter: D=0.15 m; Q = 0.06 m³/s; hf = 50 m [head losses] Find, f=? [friction coefficient], and roughnes=? [mm] Ref¹/2_D32 (20¹4) 12 Resistance coefficient, j 0.100 0.090 0.080 0.070 0.060 0.050 0.040 0.030 0.025 0.020 0.015 0.010 0.009 0.008 10³ Re 2 10³ 2 J 4 6 810² 468104 2 8104 2 4 6 8105 2 4 6 8105 Fully rough turbulent flow Smooth pipes 4 68105 2 46810 Re=VD 2 468 468107 ▬▬▬ WITH IN 0.05 0.04 0.03 0.02 0.015 0.01 0.00810 0.006 0.004 0.002 0.001 0.0008 0.0006 0.0004 0.0002 0.0001 0.00005 0.00001 6 8108 Relative roughness, 7
Engine oil at 40 C [density 876 kg/m^3, viscosity 0.2177 kg/m.s] flows in a 20-cm-diameter pipe at a velocity of 0.9 m/s. The pressure drop (in Pa) of oil for a pipe length of 20 m is
The oil is pumped from a reservoir tank to the automobile tank. The volume flow rate of oil is 3,2 cm/s. The pipe diameter is 5 mm. The oil discharges through a 0.8-mm nozzle in a tank. The pressure in the tank is 95 kPa. The total head loss in the system is 1.1 m. If the pump has an efficiency of 58,18%, determine the power [W] needed by the pump. (NOTE: Po = 673 kg/m) 05 m 95 kPa 100 kPa Pump
Add the energy grade line (EGL) as a solid line and the hydraulic grade line (HGL) as a dashed line to the figure below. Enter the corresponding numbers in the table. Assume steady incompressible flow from left to right. At point A, the pressure head P/y = 8 ft and the velocity is V=8 ft/s. The first turbine extracts AH = 10 ft, and the second turbine extracts AH = 5 ft. [ft] Ply Z V²/(28) EGL HGL EGL and HGL [ft] 30 25 2 10 50 O >> EGL_HGL (2,2,2,'T','T',-30,'ft') A D₁ =2 ft B C D₂ =2 ft; DE P3 = 2 ft F 0 5 A 10 B 20 25 15 x [1000 ft] C D 30 E F
Engine oil at 40 C [density 876 kg/m^3, viscosity 0.2177 kg/m.s] flows in a 21-cm-diameter pipe at a velocity of 1.1 m/s. The pressure drop (in Pa) of oil for a pipe length of 24 m is ?"
Needs Complete solution with 100 % accuracy
i need clear ans by hand and solve very very fast in 20 min and thank you | ᴅʏʙᴀʟᴀ ?✨؛
Find the mass flow rate (in grams per second) of water for a control volume system, if the volume flow rate is 2 liter per second. [Pwater = 1 Lem Volume flow rate=2(liter's) Mass flow rate? (g/s)