Consider the unity negative feedback system depicted in the figure below. The design specification requires a location of dominant poles to yield a 1.2 second settling time and an overshoot of 15%. If a compensator with a zero at -0.5 is used to achieve the specification, find the approximate location of compensator pole. K G(s) (s + 5)³ R(8) C(s) G(s)

Consider the unity negative feedback system depicted in the figure below. The design specification requires a location of dominant poles to yield a 1.2 second settling time and an overshoot of 15%. If a compensator with a zero at -0.5 is used to achieve the specification, find the approximate location of compensator pole. K G(s) (s + 5)³ R(8) C(s) G(s)

Electricity for Refrigeration, Heating, and Air Conditioning (MindTap Course List)

10th Edition

ISBN:9781337399128

Author:Russell E. Smith

Publisher:Russell E. Smith

Chapter11: Thermostats, Pressure Switches, And Other Electric Control Devices

Section: Chapter Questions

Problem 23RQ

See similar textbooks

Similar questions

A single-phase full-wave converter in the figure below is supplied with a 120-V, 60-Hz source. The load is highly inductive and the load current is continuous and free of ripples. The electromotive force is neglected (E 0) and the resistance has a value of R = 10 Q. The delay angle is equal to 31.8°. The average output current is 9.18A and the nth harmonic component is expressed as below. The harmonic factor (known as THD) would be equal to: R 2. vZ.1. Ir = Vo n. T +Yi, = I, E Select one: O a. 58.3% Ob. 48.3% O C. 78.3% Od. 68.3%
seels e A unity feedback system has G(s) as shown below in figure, what is the range K for * ?stability K(1+0.25)(1 +0.0255) () = 51+ 0.001 ) + 0,005 5) 600
Q.An integrator converts input signal into ........ waveform. triangular nonf of above square pulse
An alternative signal Vin=3sin(2π400t) is applied to the integrator circuit input designed with Op-Amp, which is given in the figure and fed with ±10V. Draw the waveform by analyzing the output voltage (Vo). Calculate the maximum and rms value of the output signal.
An op-amp comparator in a firing circuit can produce waveforms at the output of up to 28 V peak-to-peak without any distortion. An inverse cosine-based firing circuit with a voltage range from +14 to -14 (reference voltage) is used to produce a gating signal for the SCR at the desired delay angle. if the reference voltage is 5.92 volts, the delay angle (in degrees) would be: O A. -155 O B. None of the other choices are correct O C. 155 O D.-25 O E. 65
2. b) (i) Derive an expression for the differentiator using op-amp. (ii) Design a circuit to perform differentiation of an input signal that varies in frequency from 20HZ to about 2 KHz. (iii) If a sine wave of 0.5 V peak at 2 KHz is applied to the differentiator of part (ii), draw the output waveform.
One advantage of having feedback in op amp circuit is A.Can control gain B.less complicated C.less input signal D.low gain E.high output voltage F.low bandwidth
write forward paths and feedback paths.
6. An AC precision integrator is desired for a particular application to perform the operation: Vo'(t) = -1200 Vi(t) dt The primes indicate the ac portions of the respective functions. The lowest frequency other than a possible de component of the input signal is estimated to be 1.5 kHz. Determine a suitable design. 7. A low frequency differentiator is desired for a particular application n to perform the operation Vo(t) = -0.002 dvi(t)/ dt Based on a periodic signal with a frequency of 1 kHz, determine a suitable design. 8. Design an astable 555 timer circuit to produce 1kHz square wave, where TH = 0.35 ms and T₁ = 0.65 ms. Select C = 0.01 UE, Determine R₁ and Ra. 9. Design a monostable 555 timer circuit to produce an output pulse 5 ms wide. 10. Using op amps with Xsat = +/- 13 V, design a square/ triangular wave function generator circuit to generate 2 kHz triangular wave with a peak-to-peak voltage of 12 V. 11. Design a non inverting Schmitt trigger circuit with VT to be adjustable…
what is the output waveform and phase shift of the integrator circuit given?
An op-amp comparator in a firing circuit can produce waveforms at the output of up to 20 V peak-to-peak without any distortion. An inverse cosine-based firing circuit with a voltage range from +10 to -10 (reference voltage) is used to produce a gating signal for the SCR at the desired delay angle. if the reference voltage is -5.01 volts, the delay angle (in degrees) would be: O A. None of the other choices are correct O B. 150 O C. -120 O D. 120 O E. 60
Using any number of Op-Amps, design multistage amplifier to amplify input Ac signal with 0.01V amplitude, the expected output voltage would have 4V amplitude. The input signal frequency = 10 KHz. Assume gain bandwidth product of Op-Amp = 1 MHz