A single-phase full-wave converter in the figure below is supplied with a 120-V, 60-Hz source. The load is highly inductive and the load current is continuous and free of ripples. The electromotive force is neglected (E 0) and the resistance has a value of R = 10 Q. The delay angle is equal to 31.8°. The average output current is 9.18A and the nth harmonic component is expressed as below. The harmonic factor (known as THD) would be equal to: AT R 2. v2. 1. Ir = Vo L n.T +Yi, = I, E Select one: 58.3% Ob. 48.3% O C. 78.3% Od. 68.3%

A single-phase full-wave converter in the figure below is supplied with a 120-V, 60-Hz source. The load is highly inductive and the load current is continuous and free of ripples. The electromotive force is neglected (E 0) and the resistance has a value of R = 10 Q. The delay angle is equal to 31.8°. The average output current is 9.18A and the nth harmonic component is expressed as below. The harmonic factor (known as THD) would be equal to: AT R 2. v2. 1. Ir = Vo L n.T +Yi, = I, E Select one: 58.3% Ob. 48.3% O C. 78.3% Od. 68.3%

Delmar's Standard Textbook Of Electricity

7th Edition

ISBN:9781337900348

Author:Stephen L. Herman

Publisher:Stephen L. Herman

Chapter21: Resistive-capacitive Series Circuits

Section: Chapter Questions

Problem 7RQ: An RC series circuit is connected to a 120-V, 60-Hz power source. The resistor is 25 and has a...

See similar textbooks

Similar questions

C'uk Converter Design A C'uk converter has an input of 12 V and is to have an output of - 24 V supplying a 60 W load. Select the duty ratio, the switching frequency, the inductor sizes such that the change in inductor currents is no more than 12 percent of the average inductor current, the output ripple voltage is no more than 1.5 percent, and the ripple voltage across C1 is no more than 3 percent.
Design a Cuk converter that has an input of 25V and the output of -30V. The load is 60W. Specify the duty ratio, switching frequency, inductor values and capacitor values. The maximum change in inductor currents must be 20 percent of the average currents. The ripple voltage across capacitor C1 must be less than 5 percent, and the output ripple voltage must be less than 1 percent.
I am getting the output of the clamper circuit wrong, how will this circuit be output ? circuit question : Set the input voltage signal to a sinusoid with 100 Hz frequency and 20V peak-to-peak amplitude with C=1μF. Obtain and plot the input and output voltage waveforms.
Q6) The waveform of the voltage obtained after rectification is of a -----nature and therefore contains .harmonics a. Sinusoidal O b. Triangular c. Pulsating O d. Repetitive O
A step down converter is feeding an inductive load with R-10 Ohms, L15 mH and E-1sV. The supply is Vs-200v, the switching frequency is 10 kHz and the duty cycle is k-0.5. The maximum peak to peak ripple current in the load is equal to 0.34A. The erage load current la would be equal to: Select one: a. 8.5A O b. 18A Oc 11A O d. None of these
A 80 V rms is stepped down to 18V rms by a transformer. The output from the transformer is rectified using a half wave rectifier circuit and connected to a 47.5 Ω load resistor. Draw a circuit diagram of this arrangement and the waveform at each stage
Q/ Why is high frequency (Fsw ) used in Buck Converter circuits
A step down converter is operated with a duty cycle of k = 0.75. The input voltage is Vs = 20V, and the load is: L = 5mH, R = 1502. The minimum inductor current is I₁ = 0.1A. The maximum inductor current is: Select one: a. 1.9 A b. None of these OC. 0.9 A O d. 1.1 A Oe. 2 A
The inductor current of a buck-boost converter is shown in the figure. The minimum inductor current is zero and the peak value is 5A. The load resistor 5 A value is equal to R=702 Assume that the output voltage ripple is 1%. All components are ideal. Determine. a) Duty ratio. b) Output voltage. c) Input voltage d) Inductor value e) Capacitor value. 12μ 20μ 32μ 40μ t,sec
Boost Converter Design A boost converter is required to have an output voltage of 8 V and supply a load current of 1 A. The input voltage varies from 2.7 to 4.2 V. A control circuit adjusts the duty ratio to keep the output voltage constant. Select the switching frequency. Determine a value for the inductor such that the variation in inductor current is no more than 40 percent of the average inductor current for all operating conditions. Determine a value of an ideal capacitor such that the output voltage ripple is no more than 2 percent. Determine the maximum capacitor equivalent series resistance for a 2 percent ripple.
Question 4 A boost converter has an input of 5V and an output of 20W at 15V. The minimum inductor current must be no less than 50% of the average. The output voltage ripple must be less than 1%. The switching frequency is 30kHz. Determine the duty ratio, minimum inductor value, and minimum capacitor value. Verify your answers using Matlab, show the inductor current is continues and its minimum is no less than 50% of its average. Furthermore, the output voltage ripple is less than 1%.
Single phase full wave controlled converter circuit is powered by a single phase source. When the trigger angle is 0 °, the DC output voltage taken from the output of the converter circuit is 300V. If the trigger angle is 60 °, what is the value of the DC output voltage to be obtained at the output? i have 1 houre