Consider the steady laminar flow of water at 25°C through the piping system shown below. (a) Derive the average velocity expressions at section (1). (b) Derive the average velocity expressions at section (2). R 18m 0.3 m (2) (1)

Q: (Compute) What is line OA's direction cosine angle, in degrees, from the x-axis (θx)? Note that…

A:

Q: Draw the following using the given figure: 1. 45-degree CAVALIER 2. 45-degree CABINET OBLIQUE 3.…

A: Find 1. 45-degree CAVALIER 2. 45-degree CABINET OBLIQUE 3. Isometric Drawing

Q: can you do it in polygon

A: Given vectors : A :  2 kph 45°N of E B :  2.8  kph 58°E of S C :  5.1  kph 28°W of S D : 3.2  kph…

Q: Assume the below given figure as unit length to be equal to 10 mm, draw the isometric views of…

A:

Q: (i)A point B lies 50 mm away from H.P, & at the same distance from V.P. Describe its position in all…

A:

Q: Given the top and front view create a section view.

A: Find Create a section view using the given top and front views.

Q: TS DIAGRAM

A:

Q: (degree) Calculate the measure of the angle in degrees marked in white for the following figure 24…

A:

Q: (Compute) What is line OA's direction cosine angle, in degrees, from the y-axis (θy)? Note that…

A: The cosine angle between two vectors  is as followes,

Q: For the following figure assume the box as 10 mm and sketch the following view using CREO PARAMETRIC…

A:

Q: The object shows the center of the whole is three inches from the left surface and one inch from the…

A: we have to determine what kind of dimensions are used in the hole

Q: I'm playing a game of pool with by brother; he's stripes. At some point, I notice I have a…

A: V = 6 oz = 0.17 gd = 2.25 inches = 0.057 me = 0.95  "coefficient of restitution" "coefficient of…

Q: For the given isometric drawing, draw the corresponding top, front and right side views

A: According to the given data A isometric view of a object  We need to draw  The corresponding top,…

Q: A1A) Space is . . dimensional. O a. four O b. two O c. three O d. one

A: The space is three-dimensional because each and every point in space is  described by a linear…

Q: What is the center of gravity in this figure?

A: given; center of gravity on given figure?

Q: For the given isometric drawings, draw the corresponding top, front, and right side views

A: Note: As per policy, we can solve the first question from the multiple questions. Please resubmit…

Q: 30r 20dls 20 10r 20 20 30 150 100

A:

Q: Given the isometric drawing of the solid, draw the multiview projection. L HRP FRP L FRP PRP L

A: Given the isometric drawing of the solid, draw the multiview projection.

Q: I didn't understand how you fond the angle teta

A: For solution refer below images.

Q: is 60 left or right?

A: The horizontal reaction at A: 60 kN (Right)......(Option D)

Q: Directions: Draw an isometric view of the following orthographic views. Views most be properly…

A: Draw an isometric view of the following orthographic views.Views most be properly aligned attached.…

Q: Creste an sometre ptora and thena caet ut l the folloing abject. The grid soacing is 10 mm.

A:

Q: (Compute) What is line OA's direction cosine angle, in degrees, from the z-axis (θz)? Note that…

A:

Q: Draw the isometric figure given the views below. Will thumbs up if correct. Thank you.

A:

Q: i need the answer quickly

A:

Q: Given the multiview projection of the solid, draw the isometric view. HRP FRP F DA FRP PRP

A: Given the multiview projection of the solid, draw the isometric view.

Q: Draw the plan, Front view and the Side view of the following figure and do the dimensioning.

A: Please refer the following orthographic views of the given object.

Q: Why cos(60 if I don't see that angle in the figure

A: This question can be solved by labelling angles.

Q: Draw an orthographic(three-view drawing) of the four objects including front, top, and right views

A:

Q: Find Rab for the circuit fn figure. 202 202 Rab 792 252

A: The circuit is shown below.

Q: 3 show all steps in detail, units and formulas please.

A:

Q: I need help matching the following terms to the phrase it describes. Answers are used only once.

A: The correct answers are matched for the corresponding terms as shown below:

Q: C O C

A: Given: Hatching: Differentiates the areas that are cut and those areas that are not cut by the…

Q: Q1: Use scale (1:1), draw the front, top & side views of shape shown below. (50 M)

A: Orthographic Projection It is a form of presenting a three-dimensional object into Two dimensional.…

Q: To create a Polyline or Polygon geometry object, which two objects must first be created?

A: A polyline is a connected sequence of a line segment created as a single object and a polygon is a…

Q: PLease draw the top view and section view with dimension of the figure

A: Here is Top View and Section View of figure with well dimensioned.

Q: Draw the orthographic Projections of given object.

A: Orthographic projections are projections of a component in three directions that are perpendicular…

Q: Question 3) On the plate in the figure, the length L is given as L = 18 m . According to this; y 2L…

A: Given data: Image with relevant details   To determine: X and Y coordinate of the geometric center

Q: Below are incomplete views of the parts or figures. Complete them by drawing the lines of…

A: Note: As per the policy, we can solve the first question from the multiple question. Please,…

Q: 6 Using the drawing callout shown in Figure 5 below, which part(s) shown in Figure 4 would now…

A: According to the given dimensional tolerance for the part, the maximum and minimum allowable…

Q: Partition the given figure and find the x and y coordinates.

A: Task at hand is to find the centroid of the shape in the figure

Q: L HRP FRP (TOP VIEW) (FRONT VIEW) L (RIGHT SIDE VIEW) L

A:

Q: Question 3) The length L is given as L=34 m on the plate in the figure. According to this; Question…

A:

Q: P1-10) Sketch the front, top and right side views of the following object. Use the grid provided. D

A: According to the given data A 3-D object is given we need to findThree projection view

Engineering Drawing

Technical drawing has been around since ancient times. As in the ancient Renaissance, complicated drawings were created, including Leonardo da Vinci's drawing. Modern engineering drawing, including its specific orthographic projection with scale conventions, began in Europe (France) during the early stages of Industrialization. L.T. C. Rolt also made some of Marc's drawings for its block-making machinery (in 1799) that also may have contributed significantly to British engineering technology. Since he learned the art of presenting three-dimensional(3D) items in a two-dimensional(2D) plane, as we now term mechanical drawing.