Consider the sinusoidal voltage and current: v(t) = 170 cos(120rt- 60°) V and i(t) 60 sin(120nt- 30°) A. !! Plot v(t) and i(t) and determine if the current is leading or lagging the voltage. Find the Phasor representations of both voltage and current. Determine the rms values of both voltage and current. a) b) c)

Consider the sinusoidal voltage and current: v(t) = 170 cos(120rt- 60°) V and i(t) 60 sin(120nt- 30°) A. !! Plot v(t) and i(t) and determine if the current is leading or lagging the voltage. Find the Phasor representations of both voltage and current. Determine the rms values of both voltage and current. a) b) c)

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter2: Fundamentals

Section: Chapter Questions

Problem 2.7P: Let a 100V sinusoidal source be connected to a series combination of a 3 resistor, an 8 inductor,...

See similar textbooks

Similar questions

The rms value of v(t)=Vmaxcos(t+) is given by a. Vmax b. Vmax/2 c. 2Vmax d. 2Vmax
The average value of a double-frequency sinusoid, sin2(t+), is given by (a) 1 (b) (c) Zero
Shown in the figure below is an "RC" circuit drive by an AC power source. The AC power source has an RMS voltage of Vps (RMS) = 11.58 Volts and is running at a frequency of f = 1.326e+04 Hz. resistor has a resistance of R = 3750 2 and the capacitor has an capacitance of C = 3.17e-09 Farads. Vps R ww Write the FORMULA for the total impedance of the circuit Ztot = Write the FORMULA for the phase of the total impedance of the circuit tot = Determine the numerical value of Ztot = Determine the numerical value of Pztot= Determine the current through the circuit: • I(PEAK) = • I(RMS) = Determine the voltage across the resistor: Amps Amps S2 C degrees
1. What effect does changing the frequency on the effective value of sinusoidal voltage? 2. What effect does changing the amplitude on the effective value of sinusoidal voltage?
For the phasor diagram in figure 6 express the voltages in sinusoids for a period of 5ms. Im Re )e,=45° e,=20 Vz=10 V2=8 Figure 7 a. Va(t)=. b. V2(t)=. c. What is the rms voltage of V1 = d. What is the rms voltage of V2=_ e. What is the frequency in Hz = f. What is the angular frequency =. In terms of lagging and leading what is the exact phase relationship between V, (t) and V2(t) g.
P.4: Find the rms value for the following sinusoidal waveforms a. v = 20 sin 754t b. v = 7.07 sin 377t c. i = 0.006 sin(400t + 20°) d. i 16 x 10-3 sin(377t - 10°)
For the below sinusoidal voltage trace displayed by the CRO, the time/cm switch is on 0.2ms/cm and the volt/cm switch is on 1 V/cm. a) the frequency will be Hz b) the r.m.s value will be In CRO the beam can also be shifted vertically by applving a suitable DC voltage to the
Problem # 5 Consider the sinusoidal voltage and current shown below: v(t) = 170 cos(120zt - 60°) V and i(t) = 60 sin(120xt - 30°) A. Plot v(t) and i(t) and determine if the current is leading or lagging the voltage. Find the Phasor representations of both voltage and current. Determine the rms values of both voltage and current. Determine the apparent power, S, P, Q, pf, and r.f. a) b) c) d)
Using a line phasor (circle), draw the two given phasors. Use the sine function as the base function.
Write the sinusoidal equation of the following waveform a. 4e (V) f=60 Hz 30 b. 0.01 f= 40 Hz - 100°-
The capacitive reactance (XC).... be affected by the harmonics of non- * .sinusoidal wave will all-of-them O could O cannot O
P3 Calculate the correction factor of sinusoidal, square and triangular waveforms. VRMS Correction Factor = V Average 51931