A sinusoidal voltage source is represented by the vector pointing to 6 + j4 on the complex plane. It has a phasor representation in the form, Magnitude Z Phase° . What is the magnitude of the phasor equivalent of the source? (Note: Consider the effective magnitude when converting. Provide your answers in decimal form, up to 3 decimal places.)

A sinusoidal voltage source is represented by the vector pointing to 6 + j4 on the complex plane. It has a phasor representation in the form, Magnitude Z Phase° . What is the magnitude of the phasor equivalent of the source? (Note: Consider the effective magnitude when converting. Provide your answers in decimal form, up to 3 decimal places.)

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter2: Fundamentals

Section: Chapter Questions

Problem 2.1MCQ: The rms value of v(t)=Vmaxcos(t+) is given by a. Vmax b. Vmax/2 c. 2Vmax d. 2Vmax

See similar textbooks

Similar questions

Using a line phasor (circle), draw the two given phasors. Use the sine function as the base function.
An electrical circuit with a sinusoidal voltage source, a resistor, and a capacitor all connected in series. The voltage across the capacitor: Select one: a. Leads the current in the capacitor by exactly 90o b. Is in phase with the sinusoidal voltage source c. Is in phase with the voltage across the resistor d. Leads the current in the circuit by 90o e. Lags the current in the circuit by 90o
For the circuit below a. Find total impedance and admittance of the circuit in polar form.b. Find total current and current through each element in phasor form.c. Draw the phasor diagram for the currents I, IR, IL, IC and the voltage E and find the time domain sinusoidal expressions for the currents and voltage (use peak values for the amplitudes).
Step by step answer how to converting Rectangular form, Phasor form, and sinusoidal form
a) Using your own words, describe how triangular waveforms are produced from sinusoidal waveforms. b) Write a sinusoidal formula that will produce a triangular wavefor y c) Demonstrate your understanding by plotting the formula shown in b using any of the plotting software.
What impedance vector (0- j15) Ohms represents:A. A pure resistance. C. A pure capacitance.B. A pure inductance. D. An inductance combined with a capacitance.
Shown in the figure below is an "RC" circuit drive by an AC power source. The AC power source has an RMS voltage of Vps (RMS) = 11.58 Volts and is running at a frequency of f = 1.326e+04 Hz. resistor has a resistance of R = 3750 2 and the capacitor has an capacitance of C = 3.17e-09 Farads. Vps R ww Write the FORMULA for the total impedance of the circuit Ztot = Write the FORMULA for the phase of the total impedance of the circuit tot = Determine the numerical value of Ztot = Determine the numerical value of Pztot= Determine the current through the circuit: • I(PEAK) = • I(RMS) = Determine the voltage across the resistor: Amps Amps S2 C degrees
Determine the total impedance as seen by the voltage source. If the voltage source can be represented by a unitary phasor (Vs=1) , determine the phasor of the current I passing through the voltage source as well as the phasor of the voltage across the resistor R.
An inductor, a capacitor, and a resistor are connected in parallel with a function generator. The inductor draws 100mA RMS, the capacitor draws 150mA RMS, and the resistor draws 200mA RMS. Find the magnitude of the total current.
A sinusoidal voltage is zero and increasing at t= -1.2ms. The next zero crossing occursat t= 5.6ms. Calculate the Period T and Frequency f.
transform sinusoidals to phasor.
Task (3) Al Hussein Technical University You are given the below parallel RLC circuit, answer the following questions showing the detailed steps. 1.5 μF Lis 300 mH 220 V R3 300 2 L2 120 mH 50 Hz 0.5 µF Figure 3: Parallel RLC Circuit a) Total impedance of the circuit b) The voltage and current Phase shifts of the total impedence. c) The voltage across C1 and the current flows through it. d) The voltage across L1 and C2. e) The currents flow through L1, R and L2.