Consider the pipe assembly in (Figure 1). {30i+20j 30k} N and (60i 10j-35k} N. F1 F2 0.8 m 1.20 m 0.4 m Determine the moment of force F₁ about point A Enter the components of the moment separated by commas. Express your answers in newton-meters to three significant figures. (MA) (M) (M)-360,0-360 N-m Previous Answers Correct Determine the moment of force F2 about point A Enter the components of the moment separated by commas. Express your answer in newton-meters to three significant figures. (M) (Male (M) 420-140-680 N ✓ Correct Add these moments and calculate the magnitude of the resultant moment. Express your answer to three significant figures and include the appropriate units. Calculate the coordinate direction angle a of the resultant moment. Express your answer in degrees to three significant figures. Calculate the coordinate direction angle ẞ of the resultant moment. Express your answer in degrees to three significant figures. Calculate the coordinate direction angle ry of the resultant moment. Express your answer in degrees to three significant figures.

Q: The throttle-control lever OA rotates in the range 0 ≤ 0 ≤ 90°. An internal torsional return spring…

A: Given, Restoring moment M=Kθ+π4 K=650 N-mm/rad Radius r=35 mm Distance d=70 mm

Q: 113k 78k 9 ft G H 78k 9 ft D 78k E 9 ft A C B 9 ft- -9 ft-

A:

Q: USE MOMENT DISTRIBUTION METHOD

A:

Q: Determine the reactions at the supports, then draw the moment diagram for each member (El is…

A: Given: i=1 The length horizontal member of the frame is i+4=1+4=5 m. The length vertical member of…

Q: 90 mm `120 mm 160 mm B 120 mm D E

A:

Q: Consider the frame below, which is supported by a hinge at D and a roller against a vertical wall at…

A: Step 1

Q: The throttle-control lever OA rotates in the range 0 ≤ 0 ≤ 90°. An internal torsional return spring…

A: Given data: r=30mm k = 670N.mm/rad

Q: y | 1 A -X 25' 15⁰ 40° C F = 13 kips 15' B 11 .n

A:

Q: 5. DETERMINE THE MOMENT OF THE FORCE ABOUT POINT O IF F IS 550N. 0.4 m FIGURE 5 0.3 m F 300

A: Resolve force in horizontal and vertical direction.  Moment (M) = r*F              Where,…

Q: Determine the maximum moment from the tables using super position give your answers to one decimal…

A: Objective: To determine the maximum moment for the given beam.   Given: w = 0.41 (k/ft) P = 4.1 (k)…

Q: The throttle-control lever OA rotates in the range 0 ≤ 0 ≤ 90°. An internal torsional return spring…

A:

Q: Collar C moves with a constant speed v =6 ft/sec along the fixed rod AB where ß =33° and d = 6 ft,…

A: Velocity = 6 ft./secβ = 33°d = 6 ft

Q: From the given figure shown: Use only area moment method: (A is pin and B is roller). El is…

A:

Q: Q1. Determine the resultant moment 6+be fig. show n below: 200N 3m_ 70 8OON

A: Moment: It is defined as the tendency of a force to produce rotation about an axis or point. The…

Q: Determine the magnitude of the moment (Nm) of the force P = 211 N about the line DE. Round off only…

A:

Q: The force system shown consists of the couple C and four forces. If the resultant of this system is…

A: Consider the given figure.

Q: Calculate the vertical reaction at B. L

A:

Q: of A 2011 B 3.5 k/ft 30 ft 20 ft

A: Given data : Indeterminate beam with Fixed support at A and D and Roller at B and C Find : Reactions…

Q: The A beam shown in the figure is subjected to concentrated loads at point c and D. span AB has a…

A:

Q: The throttle-control lever OA rotates in the range 0 ≤ 0 ≤ 90°. An internal torsional return spring…

A: Given data: k=690 N-mm/rad M=k θ+π4 r=45 mm d=95 mm   It is required to determine tension T  to make…

Q: Ex: A Torque (T) is applied to a solid taper shaft with built-in ends, as shown in Figure, Determine…

A:

Q: A 331-lb block is resting on a rough horizontal surface for which the coefficient of friction is…

A: To Determine The force P (lb) required to cause motion to impend if applied to the block…

Q: Obtain the elastic curve of the ABC bar by the "Initial Values Method". Calculate the rotation (OA)…

A: Given data   We have to Obtain the elastic curve of the ABC bar by the "Initial Values Method".…

Q: Calculate the moment Mo of the 240-N force about the base point O of the robot. The moment is…

A:

Q: L A 25' 15⁰ 40° C F = 13 kips 15' B n

A: A simply supported beam inclined at 15°Force of 13 kips acting at C at 40 ° with vertical of…

Q: any method you like, solve the following unknowns: (WALAY TYPO ANI. BASAHA UG SABTA) Let w = 62N/m.…

A: Considering reference point  as A , The moment MAB and MBCcan be calculated as. MAB= W8 ×L2…

Q: PROBLEM - ASSIGN ALL PARTS NOTE: This is a multi-part question. Once an answer is submitted, you…

A:

Q: QI: The three forces shown in Figure are required to cause a 250 N as a resultant acting…

A:

Q: Determine the internal moment at B in kN-m when P = 85 and w = 28. Express your answer in 1 decimal…

A:

Q: Consider the system shown in Cauca.11 Figure 4m 6m 1of1 ) Bott Hed Part A Determine the z, y, and a…

A:

Q: M = R(8+2/4), and plot tension nake the net moment about O zero. The effects of the radius of the…

A:

Q: RM 300 ↓ 1m

A: