Consider the following transfer function: 4 s(s2 + s + 4) How does its polar plot behave while w approaches to 0? Approaching to oo with an asymptote parallel to real axis Approaching to 0 tangent to positive imaginary axis Approaching to 00 with an asymptote parallel to imaginary axis Approaching to OO with no asymptote Approaching to 0 tangent to negative imaginary axis

Q: the equation for current decay after the switch is closed. Calculate: (b) the time constant and the…

A:

Q: Draw the circuit diagrams to differentiate between the series and parallel positive clippers and…

A: Series Clippers  A series clippers can be used to clip off the entire positive or negative half…

Q: What is the difference between the pins under number 1 and the pins under number 4, and mention when…

A: The difference between pin 1 and pin 4 is the transmitting ability (information) to external…

Q: Decimal equivalent of Octal number (764)8 is, 502 496 498 500

A:

Q: The book says I should have found 46amps. Is this a misprint?

A: as the given explanation in the previous is correct.

Q: Choose the correct instruction that will read data in from an I/0 device. IN AL, 60 IN 60, AL OUT…

A: In an I/O device the command "IN" represents the input command Here IN AL,60 means that move a…

Q: How is the high current value prevented when switching to Y / ∆ position? Or explain that it is…

A: Generally, all the induction motors are started Online directly. But starting a large number of…

Q: Q1/The Gray code (10110111101)= ( ) in decimal number None of them O 1753 O 869 O 1749 O 931 O 1750…

A: We need to do convert the gray code to decimal number

Q: The resolution of the ADC unit with the reference voltage value of 3V is set to 8 bits. If the…

A:

Q: 20. Refer to graphic H. What is the resistance needed to be equivalent to the circuit in the box,…

A:

Q: If Iab is equal to 303.109∠97 and Ib is 175∠307, Ic should be

A: Current: It is the time rate of the change of the charges. It flows from high voltage to low voltage…

Q: When no key is pressed the input port (Port B) will read

A: in the given circuit the matrix connected two ports are given in which port A output is applied to…

Q: The reciprocal of resistance is

A: The reciprocal of resistance is known as  conductance  Since  for a Conductor of length l and cross…

Q: *13. Compute the missing values to complete the following table relating to analog to digital…

A: We know relationship between analog input and digital output .

Q: For the following circuit find VL, IL, Iz and IR if RL = 180 , repeat for R₁ = 470 R$ 20 V 220 2 Vz=…

A: Given: Circuit diagram,

Q: finding the current to each resistance

A: Assign the voltages at the nodes and the currents in the resistors as shown. Use nodal analysis to…

Q: оли 의 I+ ли X₂ NIZ X₁ = = 0.0140, X₂ = 0.0145, X₁ = 0.0126 a) for which type of fault this sequnce…

A: A sequence network withX1=0.014X2=0.0145X3=0.0126

Q: Fınd i2 current values in the circuit gıven ın the fıgure and verify the cırcuıt with any package…

A: Note: Given question is software based and we don't have that software to verify the current.…

Q: 4. Below is a nonlinear scale such as ones used for reading resistance on an analog meter. There are…

A: Since you have posted a question with multiple sub parts , we will solve first three sub parts for…

Q: please redesign this please. AND Gate. same switches, power supply but different layout. thank you

A: The logic circuit is given as

Q: Q-1) هد Please write the magnetic circuit And explain the steps.

A: Given figure:Asked to explain the ircuit and write magnetic circuit?

Q: If we try to connect a wire from the bottom terminal of C going to the top terminal of H. Which of…

A: Useless of resistor means no current flows through the resistor. Current will not flows into the…

Q: finding the voltage to each resistance?

A:

Q: Problem 1 is a review of your understanding of KVL (Kirchhoff's voltage law) Using KVL find the…

A: A simple question based on network analysis and the topics described in the solution are kirchoff's…

Q: clk in1 in2 out 0 1 2 3 4 6 7 8 9 10 11 12 13 14 15 16

A: We need to tell about type of flip flop for given input and output .

Q: Please help me make these two circuits on TinkerCAD. I am having trouble understanding how to make…

A: Need to connect the given circuit in the tinkercad and then analyze the circuit with various input…

Q: Count

A: In this we have to write 0 to 25 decimal numbers to hexadecimal numbers..

Q: The gate of a J-FET must always be ---

A:

Q: It's hard to read, I need a clearly handwrite version

A:

Q: Determine the approximate value of lo of Figure 52. VDD V. - 9.5V 07 mA 5.22 mA 3.67 mA A MA 1MQ VGG…

A: We need to find out the drain current for given circuit

Q: What is Q-Point? What is stiff voltage divider? What are the emitter voltage, V₁, and current, /?

A: It is given that:Wen are given three different questions.

Q: O apren the fto the fto Date: det Iq, c, and ly 本

A: Given circuit,

Analog to Digital Converters

The analog-to-digital converter (ADC) allows circuits controlled by microprocessors, Arduinos, Raspberry Pi, and various reasonable digital circuits to be connected to the real world. In the real world, analog signals have a continuous stream of information from a variety of sources and sensors capable of measuring sound, light, temperature, or movement, in addition to the many digital systems that interact with their environment by measuring analog signals from those transducers.