Consider the Fink truss shown in (Egure 1). Suppose that F₁-600 lb and F-900 lb. Figure 1 of 1 300 -10 ft- Reer work -10 - Submit Previous Answers Request Answer * Incorrect; Try Again; 5 attempts remaining Part C Determine the force in the member BC of the truss and state if the member is in tension or compression. Express your answer using three significant figures. Enter negative value in the case of compression and positive value in the case of tension. VAZ Ivec ? Fac Submit Previous Answers Request Answer X Incorrect; Try Again; 5 attempts remaining < Return to Assignment Provide Feedback lb

Consider the Fink truss shown in (Egure 1). Suppose that F₁-600 lb and F-900 lb. Figure 1 of 1 300 -10 ft- Reer work -10 - Submit Previous Answers Request Answer * Incorrect; Try Again; 5 attempts remaining Part C Determine the force in the member BC of the truss and state if the member is in tension or compression. Express your answer using three significant figures. Enter negative value in the case of compression and positive value in the case of tension. VAZ Ivec ? Fac Submit Previous Answers Request Answer X Incorrect; Try Again; 5 attempts remaining < Return to Assignment Provide Feedback lb

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A:Y 211O 2_531929016114... -> A rod is composed of an aluminum section rigidly attached between steel and bronze sections, as shown in Figure below. Axial loads are applied at the positions indicated. If P = 11 KN and the cross sectional area of each rod is 312.5 mm, determine the stress in each section. 4P Steel Bronze |Aluminum 609.6 mm 914.4 mm 762 mm
1. Determine the force in each member of the truss loaded as shown below. Indicate whether the members are in tension or compression. Summarize your analysis by filling-up the table shown. 300 kN C Summary: 3 m Member Internal Force (KN) B АВ D E AE BC 5 m BE 400 kN CD СЕ A DE 3 m - 3 m
Using Excel and the Direct Stiffness Method, determine: (a) the active DOF displacements of the truss; (b) the member axial forces; and (c) the reactions. Verify your answers using MASTAN2 and provide an output report that shows the requested results. Draw a diagram of the truss with the member forces using (T) for tension and (C) for compression, and units of kips. 8 2 (3 Properties: E=15,000 ksi 1 6 ft A = 6 in? 5 4 P = 5 kips (1) [3] 8 ft 3.
The Figure below shows a two-member truss supporting a block of weight W. The cross-sectional areas of the members are 800 mm² for AB and 400 mm² for AC. Determine the maximum safe value of W (kN) if the working stresses are 110 MPa for AB and 120 MPa for AC. ... B 40 deg. A 60 deg. A) 38.90 в) 55.30 61.70 76.2
A cantilever of length L has a solid circular cross section of diameter D and carries a vertically downward load Wat its free end. The modulus of rigidity of the cantilever is G. Calculate the shear stress distribution across a section of the cantilever and hence determine the deflection due to shear at its free end. Ans. t = 16 W(1–4y²ID²)/3¤D², 40WL/9#GD² (downwards).
The rigid AB beam shown in the figure is supported by elastic rods 1 and 2 at points A and B. Calculate the stresses that will occur in bars 1 and 2. (E-200 GPa and A=5 cm^2) E 464 4m 3 kN/m 6m Doo 10 EA 1 77777 D | rijit 5m 7m 2EA B₁
Indicate the force of the members as compression or tension. Show your solution and draw the free body diagram of your chosen joints and section. Sample Problem 2 Determine reaction at the support and the forces of each members of the truss shown. Use joint method. F G H 15 ft ТА B 24 k 30 k 4 at 20 ft = 80 ft A 3 D 12 k E
Suppose that P1700 lb and P-2000 lb. (Figure 1) Figure 150 1 of 1 16-206-208-20-20-20- Part A Determine the force in member CD of the K truss Express your answer in kilopounds to three significant figures. Enter negative value in the case compression and positive value in the case of tension. ΞΑΣΦ. 11 Ivec FCD= Submit Part B FKI - Determine the force in member KJ of the K truss. Express your answer in kilopounds to three significant figures. Enter negative value in the case of compression and positive value in the case of tension. VAZ Ivec Submit Request Answer Provide Feedback Request Answer kip 2 kip
ull 4G 10:26 Enter your answer 10 If the weight of the block shown is 90kN and to be located at the center of gravity G. What is the tensin in cables DE, AC and BC for equilibrium? TDE = TAC = ..... TBC = .... B 3 m 4m 6 m 4m 3m
Both elements have the same section and are made of the same material. Draw the shear and moment diagrams and draw the deformed Using matrix analysis techniques Realize the structural analysis (estimate forces in the supports and displacements in the free nodes) EI = 100.000 kn-m² I 10 m² H 12 m 20 N-m 目 8 40 kN 240 kw-m 2 12 m A
QUESTION 1 The assembly consists of two rods and a horizontal bar BC. Each of the rod AB and CD is made of aluminum and has a cross-sectional area of 125 mm2. A point lqad of 5 kN is applied at point E were located 0.20 m from B. Knowing that they support the rigid member BC, calculate the deflection of point E. Modulus of elasticity for aluminium is 75 GPa. P- 5 kN 0.36 m E B C 0.44 m 0.20 m
2.4 The truss shown is the same as in Example 2.1 except that the area of bar ab is a variable. E = 200,000 MPa. (a) For what value of Aah is v. = 0? Is this a function of the magnitude of the applied load? (b) Is it possible to obtain zero u, by varying A? (c) Suppose the applied load were vertical rather than horizontal, would it then be possible to obtain zero u, by varying Aab? If so, for what value of Aab? What would be the corresponding v.? 500 kN Fah = +400.6 kN Aab 4 m 6 m 3 m Problem 2.4 Fac = -277.8 kN Aae = 8000 mm?