Consider the circuit below. The capacitor has 61 uF capacitance. R1 has 36 kQ of resistance and R2 has 15 kO of resistance. The battery outputs 124 V. The value of R3 is irrelevant. The switch has been in the right position for a long time (long enough to fully charge the capacitor). At t = O s, the switch is flipped into the left position. Calculate the magnitude of the current through the capacitor att = 2.5 s, in units of mA. %3D R3 S1 R1 C1 V1+ R2

Consider the circuit below. The capacitor has 61 uF capacitance. R1 has 36 kQ of resistance and R2 has 15 kO of resistance. The battery outputs 124 V. The value of R3 is irrelevant. The switch has been in the right position for a long time (long enough to fully charge the capacitor). At t = O s, the switch is flipped into the left position. Calculate the magnitude of the current through the capacitor att = 2.5 s, in units of mA. %3D R3 S1 R1 C1 V1+ R2

Delmar's Standard Textbook Of Electricity

7th Edition

ISBN:9781337900348

Author:Stephen L. Herman

Publisher:Stephen L. Herman

Chapter19: Capacitors

Section: Chapter Questions

Problem 2PA: You are an electrician working in an industrial plant. You discover that the problem with a certain...

See similar textbooks

Similar questions

You find that a 25-F capacitor connected to 480 VAC is defective. The storeroom has no capacitors with a 480-VAC rating. However, you find two capacitors rated at 50 F and 370 VAC. Can these two capacitors be connected in such a manner that they can replace the defective capacitor? If yes, explain how they are connected and why the capacitors will not be damaged by the lower voltage rating. If no, explain why they cannot be used without damaging the capacitor.
1. 1-5 K 30v a. what is tue T CTime constant) ? b. How long will it take for the capacutor TO rtach s0% op charge? C. What is tne voltage of capa citor apter 1 seconds? d. How many tíme constants will it take for the soltage to reach 23 v? C. Gweng that the capacitor is fully changed, how will it take por it to be 20% ? long 120v + BF what is the. T ? b. what is the voltage capacitor apter 10 sec? a. C. How many time constants will it take for Tue Vo Itage to reach 80 v.? d. Given that the capaator is Fully charged, how time constants will it be to reau many GOV!
The magnitude of the voltage applied to the electrodes of a welding machine can be adjusted in the circuit below. In the range of minimum and maximum value that variable value resistor can take What is the time interval that the capacitor will charge from 0 to 8 V?
Describe the behavior of the voltage across the resistor with time as thecapacitor charges. Explain the reason for this behavior.
1. A 2F capacitor is connected in series with a diode and a 60 resistor. The voltage of the battery is 9V. The forward voltage drop of the diode is 0.7V. Flip to close the switch at t=0. Determine the voltage and current of the capacitor at t=0, t=12s, t=24s, and t=36s. (The following table may help you with this question. Feel free to use this table (or not).) Vc VR I R1 60 H Time=0 Time=12s Time=24s Time=36s
What voltage is boosted at the output of a multiplier.Choices: average, rms, peak, or instantaneous Which assumption is not used in the analysis of multipliers?Choices: a capacitor will not discharge, start with the cycle of the source that will forward bias the nearest diode, the output will always be multiplied, or a single diode is forward biased at a time A voltage multiplierChoices: multiplies the output voltage, has very high voltage and low current ,can employ inductors, or may not have equal numbers of diodes and capacitors A voltage regulator maintains constant voltage at the load regardless of variations atChoices: the input and output, the load, source, or in the environment Between a lower percent regulation and a higher one, which is better?Choices: lower or higher
In the diagram below, the switch S has been closed for a long time. A) What is the output voltage Vout? What is the charge on the capacitor? b) The switch is opened, so the output voltage increases. What is the time constant that describes the charging of the capacitor in terms of R and C? c) When Vout reaches 10 V, the switch closes and the capacitor begins to discharge. What is the time constant that describes the discharging in terms of R and C? Hint: Apply Kirchhoff's Rules to both loops and the sum of the currents at the junction above the capacitor in the diagram, and use I=dq/dt. If the switch opens when Vout reaches a lower value, say 5V, the capacitor will charge again, and thus one can cycle the voltage with a time constant determined by the circuit: this demonstrates the principle of operation of an electronic timer. 4R S 15 V Vout R
1. Find the voltages across the following components (a and b) after 1 second. The Capacitor is initially charged at 10V while the voltage source is 1V. Resistor R is 103 ohm while capacitor C is 1mF. a. Capacitor C b. Resistor R c. What is the best 1st order DE Method applicable to this problem?
The circuit in the figure below contains two resistors, R1 = 4.00kΩ and R2 = 5.00kΩ, and two capacitors, C1 = 4.00uF and C2 = 5.00uF, connected to a battery with emf E = 120V. If no charges exist on the capacitors before switch S is closed, determine the charge q1 on capacitor C1 1.00ms after the switch is closed. Determine the charge q2 on capacitor C2 1.00ms after the switch is closed.
Full-wave rectified sine wave circuit is used to measure the RMS value of a half square wave with the help of PMMC meter. The meter was actually calibrated for sine wave. The circuit uses a meter movement with a full scale deflection current of 200uA and internal meter resistance of 5kΩ. Assuming Non-ideal diodes having resistance 1kΩ, Analyze the circuit to determine the value of series multiplier resister and the corrected RMS voltage, if meter is to read 225V RMS full-scale.
An alternating voltage is applied to a series circuit consisting of a resistor and iron-cored inductor and a capacitor. The current in the circuit is 0.5 A and the voltages measured are 30 V across the resistor, 48 V across the inductor, 60 V across the resistor and inductor and 90 V across the capacitor. Find (a) the combined copper and iron losses in the inductor (b) the applied voltage.
The anode of a diode is connected to one terminal of a 1-KΩ resistor. The other terminal of the resistor is connected to the ground and the negative terminal of a 12-volt DC source is also grounded. The three components are connected in series. How much is the load current with the ideal diode?