Consider the beam shown. Suppose that M= 9 kip*ft, P=8 Kip,w=1.4 kip/ft and point D is located just to the left of the 8-kip load. Follow Sign Convention. Find the Internal force at section passing through point D for Np ,VD, MD, VE, ME B E A - ft 6 ft 4 ft 4 ft

Consider the beam shown. Suppose that M= 9 kip*ft, P=8 Kip,w=1.4 kip/ft and point D is located just to the left of the 8-kip load. Follow Sign Convention. Find the Internal force at section passing through point D for Np ,VD, MD, VE, ME B E A - ft 6 ft 4 ft 4 ft

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter4: Shear Forces And Bending Moments

Section: Chapter Questions

Problem 4.5.9P: A simply supported beam ABC is loaded at the end of a bracket BDE (see figure). Draw axial-force,...

See similar textbooks

Related questions

Q: For the beam loaded as shown, compute the value of (area)aB-XB. 500 N 2 m 1 m 1 m wwww 400 N/m B…

A: ∑MR2=0 4R1 = 400 (3) (2.5) +500(2) R1 = 1000 N ∑MR1=0 4R2 = 400 (3) (1.5) +500(2) R2= 700 N

Q: For the beam shown below, compute the following: Assume El = 1 X 10 W = 300N/m 1.5m 0.5m 2 m R1 RZ

A: To Find : a) the mid span deflection Y b) the maximum deflection ymax Given : free body diagram…

Q: Homework; In Figure below, a cantilever beam is subjected to an inclined force (P); calculate: 1-…

Q: P pt 200 mm C B. 250 mm 300 mm 550 mm Act Given: Beam AB 75mmx100mm Beam CD 50mmx50mm P- BkN W =…

Q: Calculate the maximum shear stress Tmax and the maximum bending stress σmax in a simply supported…

A: Given data: The uniform load on the beam, w = 18 kN/m. The length of the beam, l = 1.75 m. The…

Q: |1200 Ib | 1200 Ib 3 ft R2

A: Note: As per bartelby guideline first three subpart are solved. please upload other part separately…

Q: A simple uniformly distributed 20 ft. beam carrying a load of 1000 lb./ft. is simply supported at…

Q: Problem 1 [30pts] The cross section of a rectangular beam having width b and height h is shown in…

A: Section modulus on any section is given by Z=Iy Where I=Area Moment of inertia about the axis of…

Q: the beam are as follows: IPN 280 section, L = 3.5 m, P = 18 kN, and a = 26.57°. (Note: See Table E-2…

Q: A simply supported composite beam 3 m long carries a uniformly distributed load of intensity q=3…

Q: 2. A simple wooden beam, 50 mm wide by 250 mm deep and 7.5 m long has a maximum deflection of 102 mm…

A: Answer: The flexural stress is 27 MPa.

Q: Example: Draw Shear & Moment diagrams for the following beam 12 kN 8 kN А C В 1 m 3 m 1 m - RA = 7…

A: The free body diagram of the beam is given below,

Q: / The simply supported beam shown in Figure below has a central half of the beam enlarged, so that…

Q: Consider the beam shown in the figure. The allowable tensile and compressive of a beam material are…

Q: Figure Q5 (a) shows a wood beam reinforced with steel straps at its top and bottom. If the beam is…

A: Given data:

Q: The simple beam shown carries a uniform load w, = 10 kN/m. The dimensions a, b, c, and d are 0.6 m,…

Q: For the wood beam shown in Figure A, assume L = 1.5 mand P = 15 kN. The beam cross section shown in…

Q: Analyze the given structure and find out the slope teta at point B of the steel beam .Take E=200 GPa…

A: E=200 GPa = 200*109 Pa I=60 x106 mm4=60*106*10-12m4=60*10-6m4 AB=8m BC=15m W=2kN=2*103 N

Q: A simply supported composite beam 3 m long carries a uniformly distributed load of intensity q = 3.0…

Q: For simply supported beam below, find; Free body diagram and reaction forces Shear force value and…

A: i) Freebody Diagram and Reaction Forces: ΣMD = 0FA×7-15(1.5+2+2)-10(2)=0FA×7-102.5=0RA =14.64 KNΣFy…

Q: Figure Q5 (a) shows a wood beam reinforced with steel straps at its top and bottom. If the beam is…

A: Given Cross-section is:

Q: A cantilever beam of length L = 6 ft supports a uniform load of intensity q = 200 lb/ft and a…

Q: Consider the following uniformly loaded simple beam. The beam has a span length L = 2.5 m, the load…

Q: Find slope and deflection in beam at point C shown in figure below. Assume that modulus of…

A: Let :-∑Fy =…

Q: QUESTION 4 Solve the problem by the moment-area method. The beam has constant flexural rigidity EI.…

A: To find : The deflection δAand δB at point B and C . Given : The moment of inertia is I=18.1×106…

Q: The specifications of the inverted T section of a 4-m simply supported beam are illustrated in the…

Q: A 5-m simply supported beam with an additional 2-m overhang carries a point load equal to 45 kN at…

Q: 4. A cantilever beam with cross section shown below and span of 3 m is subjected to concentrated…

A: Given Data: The span of the beam is L = 3 m. The concentrated load acting on the beam is P at its…

Q: A simply supported composite beam 2 m long carries a uniformly distributed load of intensity q = 2.3…

A: (a) To Find : The maximum bending σw and σs. Given : The uniformly distributed load intensity is :…

Q: The simple beam shown carries a uniform load w, = 10 kN/m. The dimensions a, b, c, and d are 0.6 m,…

A: Draw the free-body diagram of the beam.

Q: The Cantilever beam ABC in figure below (a) consist of two segment AB and 21, for segment BC.…

A: When any beam is subjected to load, the beam tends to deviate. When a beam deflects, the neutral…

Q: A overhang beam hanged at B(6m) has two loads of 8 & 4 kn at 6 and 9 m. Calulate its moment using…

Q: The composite beam in Figure 1 is made of wood (Ew = 15 GPa), zirconium on top (Ez = 100 GPa) and…

Q: A beam is subjected to equal 6.5 kip-ft bending moments, as shown in the following Fig a. The…

A: The magnitude of normal bending stress is zero at the neutral axis and changes its sign above and…

Q: Q1 A cantilever beam AB of isosceles trapezoidal cross section has length L = 0.8 m, dimension bi =…

A: For solution refer below images.

Q: The simple beam carries a concentrated load P = 20kN. Dimension a and b are 2.5m and 1.5m.…

Q: Homework: In the Figure below, a cantilever beam is subjected to an inclined force (P); calculate…

Q: A cantilever beam AB, loaded by a uniform load and a concentrated load (see figure), is constructed…

A: If the cross section has the dimensions stated and the moment of inertia about the z-axis is 3.10…

Q: 10.4-2 A fixed-end beam AB carries point load P acting at point C. The beam has a rectangular cross…

Q: Calculate the maximum shear stress o h, 10.1 in., and the shear force V = 4,700 Ib. (Enter the…

A: Givenb=14int=0.5inh=11inh1=10.1inV=4700lb

Q: What is the span length L (in ft) of a uniformly loaded, simple beam of wide-flange cross section…

A: Given : The maximum bending stress = 11400 psi The maximum deflection = 0.1 in The modulus of…

Q: A simply supported beam is loaded with apoint load, as shown in the figure. The beam is a steelwide…

A: Given data as per question P = 10 kips f L =10 ft a = 7 ft b = 3 ft

Q: Beam ABCD is simply supported at B and C and has overhangs at each end (see Fig, a). The span length…

A: Here two different types of loading are being applied on the overhanging beam ABCD. Shear forces and…

Q: A cantilever beam AB of length L = 6.5 ft supports a trapezoidal distributed load of peak intensity…

A: Given Data The length of the beam is: L=6.5 ft=78 in From the properties of wide flange The…

Q: Mo Мо А В X+ L

A: A beam is defined as a structural member subjected to transverse shear load during its…

Q: A beam had an isosceles triangular cross section (see figure below). The maximum flexural stress is…

A: Given Data The maximum stress applied on the beam is: σ=90 MPa The Base of the triangle beam is:…

Q: If Mz = 200 kip-ft, find the magnitude of the bending stress at a point H. For the beam cross…

Q: A cantilever beam AB of length L = 6.5 ft supports a trapezoidal distributed load of peak intensity…

Concept explainers

Slope and Deflection

The slope in a deflected beam is described as an angle in radians made by the tangent of the section with the original axis of the beam. The deflection at any point on the axis of the beam is defined as the lateral displacement of the point before and after loading.

Question

Consider the beam shown. Suppose that M= 9 kip*ft, P=8 Kip,w=1.4 kip/ft and point D is located just to the
left of the 8-kip load. Follow Sign Convention.
Find the Internal force at section passing through point D for Np ,VD, Mp, VẸ, MẸ
M
E
C
A
6 ft
6 ft
4 ft
4 ft

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

Find expressions for shear force V and moment M at v = L/2 of beam AB in structure (a). Express V and M in terms of peak load intensity q0and beam length variable L. Repeat for structure (b) but find Fand M at m id-span of member BC.
A beam supporting a uniform load of intensity q throughout its length rests on pistons at points A, C and B (sec figure). The cylinders are filled with oil and are connected by a tube so that the oil pressure on each piston is the same. The pistons at A and B have diameter d1and the piston at C has diameter D2. (a) Determine the ratio of d2to d1so that the largest bending moment in the beam is as small as possible. Under these optimum conditions, what is the largest bending moment Mmaxin the beam? What is the difference in elevation between point C and the end supports?
Find expressions for shear force V and moment Mat x = 2L/3 of beam (a) in terms of peak load intensity q0 and beam length variable L. Repeat for beam (b).
Find expressions for shear force V and moment M at x = x0of beam AB in terms of peak load intensity q0and beam length variable L. Let x0= L/2.
A fixed-end beam AB of a length L is subjected to a uniform load of intensity q acting over the middle region of the beam (sec figure). Obtain a formula for the fixed-end moments MAand MBin terms of the load q, the length L, and the length h of the loaded part of the beam. Plot a graph of the fixed-end moment MAversus the length b of the loaded part of the beam. For convenience, plot the graph in the following nondimensional form: MAqL2/l2versusbL with the ratio b/L varying between its extreme values of 0 and 1. (c) For the special case in which ù = h = L/3, draw the shear-force and bending-moment diagrams for the beam, labeling all critical ordinates.
A beam with a channel section is subjected to a bending moment M having its vector at an angle 0 to the 2 axis (see figure). Determine the orientation of the neutral axis and calculate the maximum tensile stress et and maximum compressive stress ecin the beam. Use the following data: C 8 × 11.5 section, M = 20 kip-in., tan0=l/3. See Table F-3(a) of Appendix F for the dimensions and properties of the channel section.
Cantilever beam AB carries an upward uniform load of intensity q1from x = 0 to L/2 (see Fig. a) and a downward uniform load of intensity q from x = L/2 to L. Find q1in terms of q if the resulting moment at A is zero. Draw V and M diagrams for the case of both q and qtas applied loadings. Repeat part (a) for the case of an upward triangularly distributed load with peak intensity q0(see Fig. b). For part (b), find q0, instead of q1
A seesaw weighing 3 lb/ft of length is occupied by two children, each weighing 90 lb (see figure). The center of gravity of each child is 8 ft from the fulcrum. The board is 19 ft long, 8 in. wide, and 1.5 in. thick. What is the maximum bending stress in the board?
A fixed-end beam AB of a length L supports a uniform load of intensity q (see figure). Beginning with the second-order differential equation of the deflection curve (the bending-moment equation), obtain the reactions, shear forces, bending moments, slopes, and deflections of the beam. Construct the shear-force and bending-moment diagrams, Labeling all critical ordinales.
A C 200 x 17.1 channel section has an angle with equal legs attached as shown; the angle serves as a lintel beam. The combined steel section is subjected to a bending moment M having its vector directed along the z axis, as shown in the figure. The cent roi d C of the combined section is located at distances xtand ycfrom the centroid (C1) of the channel alone. Principal axes yl and yvare also shown in the figure and properties Ix1,Iy1and 0pare given. Find the orientation of the neutral axis and calculate the maximum tensile stress exand maximum compressive stress if the angle is an L 76 x 76 x 6.4 section and M = 3.5 kN - m. Use the following properties for principal axes for the combined section:/^, = 18.49 X 106 nrai4,/;| = 1.602 X 106 mm4, ep= 7.448*(CW),_r£ = 10.70 mm,andvf= 24.07 mm.
At a full d raw, an archer applies a pull of 130 N to the bowstring of the bow shown in the figure. Determine the bending moment at the midpoint of the bow.
-1 through 5.10-6 A wide-flange beam (see figure) is subjected to a shear force V. Using the dimensions of the cross section, calculate the moment of inertia and then determine the following quantities: The maximum shear stress tinixin the web. The minimum shear stress rmin in the web. The average shear stress t (obtained by dividing the shear force by the area of the web) and the ratio tmax/taver. The shear force Vweb/V carried in the web and the Vweb/V. Note: Disregard the fillets at the junctions of the web and flanges and determine all quantities, including the moment of inertia, by considering the cross section to consist of three rectangles. 5.10-1 Dimensions of cross section: b = 6 in,, ï = 0.5 in., h = 12 in,, A, = 10.5 in., and V = 30 k.