Consider the beam shown in (Figure 1). Suppose that P = 6 kip,w = 1.2 kip/ft. Point E is just to the right of the 6-kip load. Follow thesign convention.Figure-6 ft+D6 ftWB4 ft-E-4 ftT1 of 1Part ADetermine the normal force at section passing through point D.Express your answer to three significant figures and include the appropriate units.ND =SubmitPart BVD =SubmitDetermine the shear force at section passing through point D.Express your answer to three significant figures and include the appropriate units.Part CValueMDRequest Answer=ValueRequest AnswerDetermine the moment at section passing through point D.Express your answer to three significant figures and include the appropriate units.ULAUnitsValueSubmit Request AnswerUnits?Units?

Answered: Image /qna-images/answer/2f979a07-e3b5-4d7a-9ea9-8898ddbcba7f.jpg

Consider the beam shown in (Figure 1). Suppose that P = 6 kip, w = 1.2 kip/ft. Point E is just to the right of the 6-kip load. Follow the sign convention. igure 6 ft- ap D 6 ft B -4 ft E ope -4 ft < 1 of 1 > ▼ Determine the normal force at section passing through point D. Express your answer to three significant figures and include the appropriate units. ND= Value Submit Part B Request Answer VD - Value Submit Part C Determine the shear force at section passing through point D. Express your answer to three significant figures and include the appropriate units. Request Answer C MD= Value Units 4 → Ċ [[] ? 3 ? Units Determine the moment at section passing through point D. Express your answer to three significant figures and include the appropriate units. C Units ?

Consider the beam shown in (Figure 1). Suppose that P = 6 kip, w = 1.2 kip/ft. Point E is just to the right of the 6-kip load. Follow the sign convention. igure 6 ft- ap D 6 ft B -4 ft E ope -4 ft < 1 of 1 > ▼ Determine the normal force at section passing through point D. Express your answer to three significant figures and include the appropriate units. ND= Value Submit Part B Request Answer VD - Value Submit Part C Determine the shear force at section passing through point D. Express your answer to three significant figures and include the appropriate units. Request Answer C MD= Value Units 4 → Ċ [[] ? 3 ? Units Determine the moment at section passing through point D. Express your answer to three significant figures and include the appropriate units. C Units ?

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Pls help me.
STRENGTH OF MATERIALS I NEED URGENT HELP FOR MY QUESTION PLS
Need all accurate solution
NEED IN 1 HOUR PLEASE THANK U A hollow steel shaft 10 ft long must transmit a torque of 250,000 lb-in. The total angle of twist in this length is not to exceed 2.5 degrees and the allowable shearing stress is 12,000 lb/sq.in. Determine the inside and outside diameters of the shaft if G = 12 x 106 lb/sq.in. The action is elastic.
Determine the bending moment 3.5 ft to the right of point A for the beam shown belowif T = 1040 lb ft, W = 192 lb/ft, a = 5.38 ft, b = 3.77 ft, and c = 3.99 ft. Round of the final answer (in lb ft) to four decimal places. W ... B O C T b c
Show freebody diagram. Show complete and detailed solution. A steel section with force T, force F, and force C is supporting waweight of 120kN. Given the coordinates of A, B, C, and D and assuming that E is in the origin. Find the following: 1. Force T 2. Force F 3. Force C
Consider the given figure. Given: P= 22 kips. 5 kipuit 6' - hinge 6' NOTE: This is a multi-part question. Once an answer is submitted, you will be unable to return to this part. For the frame given in the figure, draw the shear and bending-moment diagrams for the frame and loading shown. Indicate axial force on a sketch. (Please upload your solution/response using the controls below)
a. Location or distance of maximum moment measured at “x” distance from point Ab. Maximum bending stressc. Bending stress at point Bd. Bending stress at point C
A hollow steel crank has an outside diameter of 57 mm and an inside diameter of 52 mm. The load magnitudes are Py= 400 N and P, = 210 N, and the length dimensions are a = 125 mm, b = 344 mm, and c = 225 mm. y Py K Pz b Determine the magnitudes of the equivalent forces and the equivalent moments that act at the section that contains point K. (a) Axial force in x direction Px (N) (b) Shear force in y direction V, (N) (c) Shear force in z direction V, (N) (d) Torque around x axis Tx (N-m) (e) Bending moment around y axis M, (N-m) (f) Bending moment around z axis M, (N-m)
What is the correct way to draw the force diagram? Drawn below are my current options
L13 L/2 L/2 B. A Prob. 5 (10 points) The figure shows a drill-rig pipe that is being picked up by a crane at point C. The pipe has dimensions L= 32 ft., do = 4. 50 in., and d; = 3. 60 in., and weighs 21 lbf/ft. At the moment when 0 = 30°, please calculate the principal stresses at: (a) the point marked B, and (b) at the point given by z = 0, y = do/2 at the same cross-section (i.e. at L/2 from the point A).
Remember to show all units and provide a step by step solution showing all work. Draw and label diagrams.Use the formula sheet.