1. Given the below 40 ft beam with a distributed load and a point load: (a) What are the reactions (forces) at supports A and B? (b) Draw the shear V and the bending moment M diagrams in the graphs. (c) What is Vmax and at what value of x is it located? (d) What is Mmax and at what value of x is it located? 10 ft 10 ft 10 ft 10 ft 8 kips/ft 10 kips B V M

Q: ㄸ

A: two Orthographic views of an object is given and we have to construct an Auxiliary view of the…

Q: Draw the figure of level and show its parts on it.

A:

Q: 120N 80N 300

A:

Q: 不 k H, k2 H3 k3 NOTE: ト -ごー*

A:

Q: 1-2in. -1in-+1int Hin 3in- T 3in 2in

A:

Q: 2) This table has three columns. First, match each set of Boundary Conditions (the left column) to…

A: Answer  Consider first Beam from middle column We get boundary condition for above beam θ0 = 0 and…

Q: 150 mm Locate the centroid of the coloured area. 50 mm 100 mm 100 mm

A: Marking points over figure- A, B, C, D, E, F In the fig three shapes can be observed clearly- 1.…

Q: & Find the set of solutions xy dx + (y-3x²) dy = 0. %3D

A:

Q: How many centimeters long is side AC?

A:

Q: Given the multiview projection of the solid, draw its isometric view.

A: Solution- The given diagram is shown below. To Determine,  The isometric view

Q: 6. Draw a true distance between a point Q and a plane B. Vs he 7. Draw a piercing point and…

A:

Q: DRAW THE SECTION INDICATED BY THE CUTTIN

A: Any view obtained by a projection on a plane other than the horizontal, frontal, and profile…

Q: Define deflection angles.

A: A deflection angle is an angle between the onward extension of the previous leg and the line ahead.…

Q: Q3. Determine the plastic moment Mp of the cross sections shown, assuming the material to be…

A:

Q: Determine the location of the centroidal x an y of the figure shown.

A: The portion which is cut out needs to be subtracted.

Q: Determine the y-coordinate of the centroid of the cross section of the underground runnel lining…

A:

Q: Select the lightest weight stell wide-flange beam that will safely support the loading shown. The…

A: The given loading is shown below:

Q: Find the length of side TS.

A: Consider the figure,

Q: Draw the front and the right side view of the given machinery part.

A: (Not drawn to the scale)   Front View:

Q: determine the degree of indeterminacy.

A: * Hinge support: - It is defined as the support which resists horizontal and vertical reaction but…

Q: For the given flat plate of uniform thickness as shown, determine the area of the section, and the…

A:

Q: that line thats extended after D isnt a member. i drew it that way to make the vertical length…

A: Given: Required : Whether structure is determinate, stable or unstable

Q: Make whatever changes or addition are necessary in each case to form a correct and complete FB.D.

A: 1) Incorrect, weight mg will act downwards 2) Incorrect, there will be frictional force acting at…

Q: What is Dutch (Deft) cone is consists of?

A: The cone penetration test (CPT) is a technique used to measure the geophysical characteristics of…

Q: What is the rod reading at the arrow? 4 3 7 3 =6

A: Rod reading:- The number on the rod is parallel to the die-observing device's height. The elevation…

Q: Draw the front, Side and top

A: For this, we can draw the diagram in Autocad. I have used the same to draw the diagram and have…

Q: 0 mm Infront of VP and 30 m rojection of the line.

A:

Q: A CPLD is based on

A: A CPLD- Complex Programmable logic device It is a programmable device based on complexity PALs and…

Q: Which shortcut key lets you rotate the drawing area? RO О тв O z O L

A:

Q: 40" -45"-

A:

Q: D O00 15KN 15KN B.

A: Given data : Number of member (m)=13Number of external support reaction (R)=2+1=3Number of joint…

Q: Hinge What is the degree of indeterminacy (i) of the frame shov

A:

Q: Draw a neat and clean diagram of the final configuration of how the bars are placed.

A: To draw the bar configuration of the given beam

Q: d²y ¸ dy + 7. - бу 3D 36х dx² dx

A:

Q: b (x+c)(x-c) A

A: To solve the expression (x+c)(x-c) step by step, we'll use the difference of squares…

Q: 33. Draw three views of the shalt guide. 22 -55 57 30 20R 15- 22 45 -85- 40 Bore 70-- PROB. 33…

A: We can represent any 3D figure in 2D by 3 views  Top view  Front view  Right / Left side view

Q: Determine the degree of indeterminacy for each of the following structures:

A:

Q: 5 \frac{4}{5}-2 \frac{1}{5}

A: Tofind:- difference

Types of Composite

Composite materials are formed by merging two components that have different chemical and physical properties. The merged output is termed as a composite, whose properties are completely different from the individual components. Composite materials also have better strength than the individual components.Composite materials usually have two main parts, reinforcement material, and matrix material. The matrix material acts as a binder and surrounds the fiber of another material that bears a much higher strength. This material is known as the reinforcement material. The matrix materials are usually high-strength additives resins, while the fibers of the reinforced material can be random, oriented, and in a mat format.Composite materials are also known as fiber-reinforced composite polymers because they are composed of the polymer matrix which is reinforced to laboratory-created fibers or naturally occurring fibers, such as glass fibers, carbon fibers, or aramid fibers. Under the application of external loads, the matrix material absorbs and transfers the loads to the fibers, these fibers in return provide good compressive strength, tensile strength, and stiffness to the fiber-reinforced composite materials.Depending upon the matrix and the reinforcement material, different properties can be induced to the fiber-reinforced composite materials, including good corrosion resistance properties. The most common matrix material is the resin while the glass fibers act as the reinforcement material. Strong fibers provide strength and stiffness to the composite materials while, a soft and flexible resin provides shape to the composite materials.