Consider continuous two-dimensional heat transfer in a rectangular cross- section solid rod as given in the figure. The measured temperatures at selected nodes of the outer surfaces are shown in the figure. The thermal conductivity of the object is given in two different ways as follows and there is no heat generation inside the object. The rectangular shape is divided into 6 equal parts as and. Find the temperatures of the determined points in the environment using the finite difference method. (1, 2, 3 and 4 points) AX = AY = 2cm ve k=20 W/m°C 120 120 100 100 120 120 [3 140 140 insulation 2.

Consider continuous two-dimensional heat transfer in a rectangular cross- section solid rod as given in the figure. The measured temperatures at selected nodes of the outer surfaces are shown in the figure. The thermal conductivity of the object is given in two different ways as follows and there is no heat generation inside the object. The rectangular shape is divided into 6 equal parts as and. Find the temperatures of the determined points in the environment using the finite difference method. (1, 2, 3 and 4 points) AX = AY = 2cm ve k=20 W/m°C 120 120 100 100 120 120 [3 140 140 insulation 2.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Diagram of the problem, necessary formulas, clearance and numerical solution Two heat reservoirs with respective temperatures of 325 K and 275 K are brought into contact by an iron rod 200 cm long and 24 cm2 in cross section. Calculate the heat flux between the reservoirs when the system reaches its steady state. The thermal conductivity of iron at 25 ◦C is 79.5 W/m K.
Consider the composite wall system formed by a flat plate of solid material I attached in series to a flat plate of solid material II as shown in IMAGE BELOW The straight lines observed in each material correspond to the temperature profiles in steady state.According to the above, you are asked: Which of the two materials has the highest thermal conductivity?
A composite wall consisting of five series layers of materials with different properties. Layer thickness, thermal conductivity of the layers and temperatures are shown on the figure. Based on Fourier's law for conduction, answer the following questions. 1. What are the main assumptions? 2. Drive an equation to calculate the heat transfer rate through the Composite wall? 3. Draw the thermal circuit through composite wall? 4. What are the value Ti? 5. What are the value Tj? 6. What are the value Tr? Givens: KA = 2 W/m. °C KB= 1 W/m.°C Kc = 5 W/m. °C Ko= 4 W/m. °C 100°C Ti 25°C Tj Tr A C +2cm + -6 cm 4cm cm
A long solid bar (k=30 W/m.K) of rectangular cross section is exposed to a constant heat flux on one surface and is subjected to convection on the opposite surface. The other two surfaces are maintained at constant temperatures as shown. Using a uniform mesh size Ax=Ay=1 cm, 6.1 express the finite difference equations for nodes 1, 2 and 3, and 6.2 solve for the nodal temperatures. 100 °C q=5,000 W/m² 300 °C ΔΧ 3 ду h = 150 W/m²K Too = 25 °C
The temperature distribution in a certain plane wall is: T-Ty =C₁+Cx²+C₁x² Where TI and T2 are the temperatures on each side of the wall. If the thermal conductivity of the wall is constant and the wall thickness is L, derive an expression for the heat generation per unit volume as a function of x, the distance from the plane where T-T1. Let the heat- generation rate be 'q0 at x = 0
FROM THE BOOK: ENGINEERING THERMOFLUIDS, M. MASSOUD.
2. The slab shown is embedded in insulating materials on five sides, while the front face experiences convection off its face. Heat is generated inside the material by an exothermic reaction equal to 1.0 kW/m'. The thermal conductivity of the slab is 0.2 W/mk. a. Simplify the heat conduction equation and integrate the resulting ID steady form of to find the temperature distribution of the slab, T(x). b. Present the temperature of the front and back faces of the slab. n-20- 10 cm IT- 25°C) 100 cm 100 cm
A wall as given in fig is made up of two layers (A) and (B) The temperatures are as shown in the sketch. The ratio of thermal conductivities of two layers is given as KA = 3 the ratio t, : t, is KB T2 = 1200 T, = 1300° C B T3 = 30 A
The lining of box-type fumace is made up of a refractory layer and steel plate as shown in the figure. Steady state temperature at the surface of the refractory is 1273 K and that at the outer steel surface is 473 K. If the steady state heat flux through the refractory-steel plate composite is 1600 W/m², and heat flow is along x-direction only, the thermal contact resistance (m² K/W) between refractory and steel is_ steel Refractory 1273K Furnace 473K Ambient Given data: Thermal conductivity of refractory = 1.2 W/m-K Thickness of refractory lining = 80mm Thermal conductivity of steel = 32 W/mK Thickness of steel plate = 4mm
!
Two approaches used in development of the thermal resistance network in the x-direction for multi-dimensional problems are to assume any plane wall normal to the x-axis to be isothermal and to assume any plane parallel to the x-axis to be adiabatic. True or False True False