Consider a silicon wafer positioned in a furnace that is zone-heated on the top section and cooled on the lower section. The wafer is placed such that the top and bottom surfaces of the wafer exchange radiation with the hot and cold zones respectively of the furnace. The zone temperatures are Tsur.h = 1200 K and Tsur,c = 330 K. The emissivity and thickness of the wafer are & = 0.65 and d = 0.78 mm, respectively. With the ambient gas at T = 700 K, convection heat transfer coefficients at the upper and lower surfaces of the wafer are 8 and 4 W/m².K. Find the steady-state temperature of the wafer, in K. Tw i K

Consider a silicon wafer positioned in a furnace that is zone-heated on the top section and cooled on the lower section. The wafer is placed such that the top and bottom surfaces of the wafer exchange radiation with the hot and cold zones respectively of the furnace. The zone temperatures are Tsur.h = 1200 K and Tsur,c = 330 K. The emissivity and thickness of the wafer are & = 0.65 and d = 0.78 mm, respectively. With the ambient gas at T = 700 K, convection heat transfer coefficients at the upper and lower surfaces of the wafer are 8 and 4 W/m².K. Find the steady-state temperature of the wafer, in K. Tw i K

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A 3-in-diameter cylindrical wire is coated in 3 inches of polyethylene insulation. The wire can be modeled as a grey body with an emissivity of .85. Due to the electrical resistance, the wire is at a temperature of 300 degrees Celsius. The insulation is also a great body with an emissivity of .95, at a temperature of 40 degrees Celsius. (Assume F12=1). What is the heat flux (W/m^2) of the energy going from the wire to the insulation?
Determine radiation heat loss from a steel tube of outside diameter 60 mm and 5m long at a temperature of 327 °C if the tube is inside a square conduit made of brick having 0.4 m side as shown in given figure and temperature of 25 °C. (Take, ɛ(steel)= 0.8, e(brick)= 0.9. Steel tube(1) Brick(2)
! Required information Irradiation on a semi-transparent medium is at a rate of 640 W/m². If 160 W/m² of the irradiation is reflected from the medium and 130 W/m² is transmitted through the medium, Determine the absorptivity of the medium. The absorptivity of the medium is 0.75 X
Question 4-83 is the one I need help with
1. A furnace is of cubical shape with the dimensions of 4m X 4m X 4m. The top surface is heated by electric resistance heaters providing a power input of3.5x10 W, the side walls are well insulated, and the bottom surface is maintained at 350K. Calculate the temperatures of the top and side surfaces if the emissivities of the top and bottom surfaces are 0.7 and 0.5, respectively.
Fast Please..
PROBLEM: IVD-19 BOOK: ENGINEERING THERMOFLUIDS, M. MASSOUD
A right circular cylinder has a height of 1 m and diameter of 75 cm. Find the view factor for the cylindrical to the base.
- A furnace can be considered like a long semicylindrical duct of diameter D = 5 m. The base (1) and the dome (2) of the furnace have emissivity's of 0.5 and 0.9 and are maintained at uniform temperatures of 305 and 1000 K, respectively. a- Draw the network of the system. b- Calculate total resistance. b- Determine the net rate of radiation heat transfer per unit length from the dome to the base surface.
An engineer is investigating objects that can be used as a solar collector. One ofthe objects considered is the object made of aluminum and is coated with leadsulfate. Investigation shows that the reflectivity of this object is 0.2 for radiationat wavelengths less than 3.3 μm and 0.95 for radiation greater than 3.3 μm. Inorder to get better insight into the behavior of the object, as a candidate for asolar absorber, the object is then exposed to two different conditions: a solarradiation (T ~ 5800 K) and a room temperature (T ~ 300 K). What is the energyreflected by the object at these two conditions?
Which one is correct answer it fast urgent
PROBLEM 4: A black thermocouple is inside a chamber with black walls. If the air around the thermocouple is at 20°C, the walls are at 100-C, and the heat transfer coefficient between the thermocouple and the air is 75 W/m²K, what temperature will the thermocouple read?