Consider a shunt linear regulator with Vin = 10V, Pz = 500mW, Vz= 2.5V and current limiting IR1(max) = 100 mA. Design a parallel regulator to yield a regulated output VOUT = 5.0 V. 10 V VINO VREF R₂ VEZDI www R₁ b) 0.5 W, 50% c) 1 W, 25% d) 1 W, 50% e) None of the above 2₁ a www Ry Vx 5 ΚΩ VouT 5V What is the rating (in Watts) for R₁ and efficiency of this linear regulator? a) 0.5 W, 25%

Consider a shunt linear regulator with Vin = 10V, Pz = 500mW, Vz= 2.5V and current limiting IR1(max) = 100 mA. Design a parallel regulator to yield a regulated output VOUT = 5.0 V. 10 V VINO VREF R₂ VEZDI www R₁ b) 0.5 W, 50% c) 1 W, 25% d) 1 W, 50% e) None of the above 2₁ a www Ry Vx 5 ΚΩ VouT 5V What is the rating (in Watts) for R₁ and efficiency of this linear regulator? a) 0.5 W, 25%

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Q2. For the circuit shown below, sketch i, & Vo 60 a. Find the conduction angle of the thyristor. b. Find the average output voltage V. R-6.50 f- Go Hz = 27AL = 120x17X10 = 6.4092 075 LO = RrjX= Vo L-17mH 6.5+j6.469=9.128 (44595 075 75V( Es 24 Vm A e
R +Vcc -Vcc C Vout R R a. Quantify how the resistors and the capacitor influence the output voltage of the circuit, Vout. What are the upper and lower limits of Vc? b. Howlong does it take for the capacitor to be charged from minimum to maximum voltage and vice versa?
3. Determine Veand Sketch output waveform for the clamper network shown. 20 V Si C Vi R 4 V- | -20 V 4. An RC filter stage (R = 42 0, C = 220 µF) is used to filter a signal of 30 V dc with 6 V rms operating from a full wave rectifier. Calculate the percentage ripple at the output of the RC Section for a 200-mA load. Also calculate the ripple of the filtered signal applied to the RC stage.
A boost regulator has L=0.15 mH and C=0.11 mF with a duty cycle of 0.66 at a switching frequency of 50 kHz. The average load current is la=0.5A. The maximum ripple output voltage is: Select one: a. None of these b. 1.6V C. 2.6V d. 0.6V
What is the output voltage across a load resistor if it is paralleled with a forward biased silicon diode? The resistor network is supplied with 10 V. * O A. 0.7 V O B. 9.3 V O C. 10 V O D. Can't be solve, lack of data.
A boost converter has an input voltage Vb=5V. The average load current is lo=0.5A. The switching frequency is 25 kHz. Suppose that a regulator is added (L=0.15 mH and C=0.22 mF) and that the current is continuous. If the average output voltage is Vo =15V, then the ripple current of the inductor delta() is equal to: Select one: a. 1.41A b. 0.56A O c. None of these d. 0.89A
Write the loop equations for a Buck converter in the two modes if the inductance is characterized by a combination of inductance L1 in series with an equivalent resistance r1, filter capacitance is characterized by a capacitor C1 in series with resistance r2. Also assume that the controlled switch has a drop of 0.4V and the freewheeling diode has a voltage drop of 0.65v. Draw the corresponding equivalent circuits in each mode.
az/a.Design Circint as the following pescripton: A. the positive Cyycle of the vout signal is 3-2 and Negadive cycle is 4-3 (Note: we must used preetical Diodes and vin is tov)
A bridge full - wave rectifier with a capacitor - input filter provides a dc output voltage of 14.5 V to a 330 ohm load. Determine the value of filter capacitor if it connected to input voltage of 12 V rms, 50 Hz. Question 7Answer a. 220 ɲf b. 208 ɲfc. 440 fd. 104 nf
For a Step-down chopper, design the circuit with 200ohm effective input resistance and 10ohm output resistance? Calculate the duty cycle and efficiency. Assume the input voltage accordingly.
Consider the Circuit below: VCC R1 RC Q1 RE Solve for IC in mA given that: RE=0.14kOhms RC=0.30kOhms R1=2.82kOhms VCC-13.12V Beta = 109.18
Boost Converter Design A boost converter is required to have an output voltage of 8 V and supply a load current of 1 A. The input voltage varies from 2.7 to 4.2 V. A control circuit adjusts the duty ratio to keep the output voltage constant. Select the switching frequency. Determine a value for the inductor such that the variation in inductor current is no more than 40 percent of the average inductor current for all operating conditions. Determine a value of an ideal capacitor such that the output voltage ripple is no more than 2 percent. Determine the maximum capacitor equivalent series resistance for a 2 percent ripple.