Consider a rectangular bar of length L and cross-sectional area A suspended vertically. Which of the following is the appropriate expression for the deformation of the bar due to its own weight and a downward force P applied on its free end? The material has a specific weight y (i.e. weight per unit volume) and a modulus of elasticity E. 8 = 8 = = d = S 2 yL² 2E yL² E + yL² 2E PL AE 7²² - PL E AE + PL AE PL AE

Consider a rectangular bar of length L and cross-sectional area A suspended vertically. Which of the following is the appropriate expression for the deformation of the bar due to its own weight and a downward force P applied on its free end? The material has a specific weight y (i.e. weight per unit volume) and a modulus of elasticity E. 8 = 8 = = d = S 2 yL² 2E yL² E + yL² 2E PL AE 7²² - PL E AE + PL AE PL AE

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A rigid beam is supported by a pin at A and two metallic wires at Band C. Determine the force P that causes the point C to displace downward by 0.2 mm. Given: E (wire B) 70 Gpa, E (wire C) = 200 Gpa and both wires have a diameter D 5 mm. Consider a linear elastic behavior.
Four axially loaded members are shown below. All members have the same value for E (Young’s modulus) and for ν (Poisson’s ratio).
Question 2 Consider the bar in figure 2, it has cross sectional area A 1.10-4m², modulus of elasticity E = = 200GPa, and length 1.5 m. The bar is fixed to a wall on its left hand side, and has a constant loading of 1(x) = −10 kN/m applied along its length. x=0.0 |(x) = -10 kN/m 1.5 m X x=1.5 Figure 2: diagram of bar subject to applied force along its length a) The displacement of the bar u(x) is governed by the equation ə du(x) AE dx dx +1(x) 0 x = [0, 1.5], state the two boundary conditions for this bar problem, and give a short reasoning for your answer (maximum 2 sentences for each boundary condition).
i need the answer quickly
A rigid beam is supported by a pin at A and two metallic wires at B and C. Determine the force P that causes the point C to displace downward by 0.3 mm. Given: E (wire B) = 70 Gpa, E (wire C) = 200 Gpa and both wires have a diameter D = 4 mm. Consider a linear elastic behavior.
The blue bar is made from steel with the following mechanical properties: Young's Modulus, E = 17x10° psi; Poisson's Ratio v = 0.31. The bar has a circular cross-section with diameter d= 0.50 in. being the length of each side. 557 lb 557 Ib 60 in. - Determine the following under the action of the axial load (assume elastic behavior): a. The bar's axial deformation, ô, in in.: b. The average axial or longitudinal strain, ELong: c. The change in the bar's diameter, in in.:
Please show complete solution and box the final answer
A long, rectangular bar (made of Material A) under a tensile load P hangs from a pin that is supported by two metal (made of Material B) posts. The Material A bar has a length of 2,0 m, a cross-sectional area of 5043 mm2 and a modulus of elasticity E=123 GPa. Each Material B metal post has a height of 0,3 m, a cross-sectional area of 4911 mm2, and a modulus of elasticity E=183 GPa. Calculate the maximum load P (in kN), if the displacement 6 is limited to 2,7 mm? Material B Post
A horizontal bar, fixed at one end (x = 0), has a length of 1 m. and cross-sectional area of 100 mm2 Its elastic modulus varies along its length as given by E(x) = 100e-x GPa, where is the length coordinate (in m) along the axis of the bar. An axial tensile load of 10 KN is applied at the free end (x = 1). The axial displacement of the free end is..... mm
A vertical load P is applied at the center B of the upper section of a homogeneous frustum of a circular cone of length L, minimum radius rB, and maximum radius rA, as shown in the figure below. It is made of a material with a modulus of elasticity E. Neglect the effect of its weight. Use the following values: rA = 2 in, rB = 0.5 in, L = 3 ft, E = 30 (103 ) ksi, and P = 1800 lbf. Discretize the original geometry into three equal-length finite elements and (a) Compute all the nodal displacements. (b) Compute all the element axial stresses. (c) Plot the displacement field from the finite element method solution. (d) Plot the axial stress field from the finite element method solution.
Two cylindrical copper alloy bars have the same length L, but different shapes, as can be seen in the figure. The two bars are subjected to the same axial load P. Use the following numerical data: P = 1400 kN, L = 5 m, d = 80 mm, E = 110 GPa, and ν = 0.33. (a) Find the change in length of each bar. (b) Find the change in volume of each bar.
L1 PB 2 E2 L2 D2 Dimensions: L2 L1 D2 D1 17 mm 18 cm 23 cm 15 mm Problem Statement: The rod shown is subjected to loads of PR = 112 kN and Pe = 18 kN. Segments AB and BC have elastic moduli of E, = 206 GPa and E = 73 GPa. The rod has circular cross-sections, and the dimensions of the rod are given above. Find the overall change in length of the rod under this load. Assume: • The collar at B is rigid • Stress concentration effects may be neglected 2014 Michael Swanbom