Consider a composite bar that is firmly attached to unyielding supports. Compute the stress in each material caused by the application of the axial load P = 30,000 lb. The area of the aluminum rod is 1.5 in² and the steel bar is 2.3 in². Assume Eal = 10 x 10 psi and Est = 29 x 10€ psi. 15 in 10 in

Consider a composite bar that is firmly attached to unyielding supports. Compute the stress in each material caused by the application of the axial load P = 30,000 lb. The area of the aluminum rod is 1.5 in² and the steel bar is 2.3 in². Assume Eal = 10 x 10 psi and Est = 29 x 10€ psi. 15 in 10 in

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A vinyl [E = 2.65 GPa; v = 0.41] block with width b = 60 mm, depth d = 120 mm, and height h = 320 mm rests on a smooth rigid base. A load P is applied to a rigid plate that rests on top of the block. Calculate the change in the depth dimension d of the block after a load of P= 180 kN is applied. Rigid plate Answer: Ad = i Width b P Depth d Height h Rigid base mm
18
Assume concrete accepts no tension. Compute the bending stress in the extreme fiber of the beam of figure for bending moment 1.25ton.m A = 10cm? E, = 2*10 kg /cm? E. = 2*10°kg /cm f' =150kg / cm? F, = 4000kg / cm? 20 cm 25 cm 20 cm
Determine the compressive force (in lb) in the bars shown after a temperature rise of 173°F if d = 0.015 in. Round off the final answer to five decimal places. Use the following data: Bronze Aluminum A = 2.24 sq. in A = 2.78 sq. in E = 14959726 psi E = 10594540 psi L = 12.5 in L = 16.6 in α = 11.61 x 10-6/ °F α = 12.67 x 10-6/°F
PROBLEM 01: Hollow bar length is 1.40m long and tube length is three-fourth as long as the bar. Torque T=1100N.m acts at the free end of the bar. Both the bar and tube are made of an aluminum alloy with shear modulus of w ww elasticity G=27GN/m². Given that dl=35mm, d2=45mm, d3=60mm, d4=70mm. Determine the following: a. Maximum shear stress in both the bar and tube b. Angle of twist at the end A of the bar. (In degrees) Tube Fixed plate End plate Tube d3 d1 d2 d4 Bar Cross-section of the bar and tube
A rectangular steel bar with given dimensions is subjected to a axial compression. What is the critical buckling load? width, b = 42 mm thick, t = 60 mm L = 3.25 E = 180 Gpa
Use the giuven values: Aluminum: E = 10 x 106 psi, α = 12.8 × 10-6 in/(in·°F) Bronze: E = 12 x 106 psi, α = 10.5 × 10-6 in/(in·°F) Show you complete solution.
SHOW COMPLETE SOLUTION AND DRAW ILLUSTRATION
Calculate the design moment strength of a reinforced concrete beam 200 mm x 460 mm if at failure the concrete compression strain is 0.003 and the tensile steel strain is 0.005. The flexure bars are 16 mm in diameter enclosed by 10 mm stirrups. Use f'c = 22 MPa and fy = 420 MPa. Express your answer as a whole number in the unit of kN.m.
The composite material is fastened to their junction at rigid plate B and attached to rigid fixed supports at both ends subjected to two loads of 12k positioned symmetrically at B. Determine the stresses and their corresponding behavior for each material. Use 2 decimal places in every solved value. 亚 А 12k 12k 1 ft Steel Est = 29 x 10° psi Ast = 1.03 in? B Aluminum 2 ft Eal = 10 × 106 psi Aal = 8.92 in² C
The composite A-36 steel bar shown is made from two segments, AB and BD, having cross-sectional areas of AB = 641 mm2 and BD = 1202 mm2 . Determine the vertical displacement (in mm) of end A. Modulus of Elasticity = 210 GPa. X = 1016 mm, Y = 790 mm, Z = 526 mm. Input the magnitude only. The answer is 0.58185. Show solution pls. Thank you.