Consider a 1 m-long bar of 2024-T81 aluminum alloy with a 20mm-diameter and the following property data: E=70GPa Y.S.=410MPa T.S.=480MPa %Elongation at failure=8% What will be the length of the bar under a structural load of 1.2×10^5N in tension? Your answer should be in units of meters (m).

Consider a 1 m-long bar of 2024-T81 aluminum alloy with a 20mm-diameter and the following property data: E=70GPa Y.S.=410MPa T.S.=480MPa %Elongation at failure=8% What will be the length of the bar under a structural load of 1.2×10^5N in tension? Your answer should be in units of meters (m).

Materials Science And Engineering Properties

1st Edition

ISBN:9781111988609

Author:Charles Gilmore

Publisher:Charles Gilmore

Chapter6: Introduction To Mechanical Properties

Section: Chapter Questions

Problem 6.2DP

See similar textbooks

Related questions

Q: A cylindrical rod with a radius of 0.3 in. and a length of 15 in. is subjected to a tensile load. If…

A: It is required to determine the stress in the rod. Here, P is the load and A is the area of the…

Q: A 20-mm-wide block is firmly bonded to rigid plates at its top and bottom. When the force P is…

A: Given data-

Q: Q5 A specimen of magnesium having a rectangular cross section of dimension= (3.2 mm X 19.l mm) and…

A: load extension stress=PA strain=δll 0 0 0 0 1380 0.03…

Q: The following picture represents a bridge comprised by a continuous horizontal beam AB that has been…

A: As per rule only one question is to be solved As per above diagram Number of reactions at A = 2, VA…

Q: As shown, three steel wires, each 27 mm2 in area, are used to lift a mass M. Their unstretched…

Q: Problem 6.2. The undeformed and deformed outline of a material element are as shown in the figure…

A: The diagram is shown below, And,

Q: Consider the truss shown in (Figure 1). Take A = 0.0015 m2 and E = 200 GPa for each member. Part A…

Q: 29. During laboratory testing of an 8-inch aluminum-alloy rod with a cross sectional area of…

A: Given:- The length of the aluminum-alloy rod during testing = 8 inch The cross-sectional area of…

Q: a= 450 mm Op t = 20 mm b= 350 mm The plate shown in the figure is made of a material having a…

A: Finding out stress sigma b.

Q: The compound bar containing steel, bronze, and aluminum segments carries the axial loads shown in…

Q: PROBLEM 01 (20 points) AN ALUMINUM SEGMENTS HAVING A DIAMETER AND LENGTHS SHOWN IN THE FIGURE. IF E…

A: Give Data: E = 75 kPa =0.075 MPa Bar-A Length LA = 800 mm Load PA = 300 N Tension Diameter = 8 mm…

Q: A piece of steel is said to have Young’s modulus of 29 × 106 psi. Based upon a yield strength of…

A: I

Q: to be in tension positive and forces causing the object to be in compression negative. As we can see…

Q: A cylindrical rod with a length of 380 mm and a diameter of 10 mm is to be subjected to a tensile…

Q: A rod made of aluminum alloy, with a gauge length of 100 mm, diameter of 10 mm, and yield strength…

A: Given: Gauge length = 100 mm Diameter = 10 mm Yield strength = 150 MPa Tensile load = 5.85 kN New…

Q: An alloy steel having a diameter of 0.45 in. extends 0.002 in. over a gage length of 2.2 in. due to…

Q: As shown, three steel wires, each 26 mm in area, are used to lift a mass M. Their unstretched…

Q: AN ALUMINUM SEGMENTS HAVING A DIAMETER AND LENGTHS SHOWN IN THE FIGURE. IF E= 85 KPa, COMPUTE THE…

A: Given E= 85 kpa = 0.085 N/mm2

Q: The compound bar containing steel, bronze, and aluminum segments carries the axial loads shown in…

A: Given -

Q: A cylindrical piece of steel 80 mm dia and 120 mm long is subjected to an axial compressive force of…

Q: 3. Two rods are assembled with area, modulus of elasticity, and coefficient of thermal expansion as…

Q: A metal specimen 36 mm in diameter has length of 360mm. A force of 300kN elongates the length by…

A: Given:- Diameter of specimen, d = 36 mm Length of specimen, L = 360 mm Force, F = 300 kN = 300000…

Q: the rectangular simply supported beam shown in (Figure 1) The beam is made of wood having a modulus…

A: Given :

Q: An aluminum rod has a diameter of 10 mm and a length of 800 mm. If an axial tensile force of 200 kN…

A: Applied load P = 200 kN = 200 x 103N length of rod l = 800 mm poisson's ratio = 0.35 E = 70 GPa =…

Q: A compound bar consisting of bronze, aluminum, and steel segments is loaded axially as shown in the…

Q: During laboratory testing of an 6-inch aluminum-alloy rod with a cross sectional area of 0.32in², a…

A: Given data : Initial Length (Li)=6 inInitial area (AI)=0.32 in2Tensile load (P)=50000 lbsFinal area…

Q: Calculate the stiffness of a homogenous bar having elastic modulus of 200 GPa, length of 2 m, and…

Q: 9. A 200 kgf load is applied to a steel bar of cross section area 6 cm?. When the same load is…

Q: A compound bar consisting of bronze, aluminum, and steel segments is loaded axially as shown in the…

Q: A 20mm-diameter bar of this alloy is used as a structural member in an engineering design. The…

Q: How much will a steel rod lengthen under tension with the following considerations? The steel rod is…

Q: Actual weight of steel bars = 1.520 kg/m, Standard weight of steel bars (16mm )= 1.579 kg/m, Load at…

Q: Calculate the stiffness of a homogenous bar having elastic modulus of 200 GPa, length of 2 m, and…

A: STIFFNESS: IT IS THE FORCE REQUIRED TO PRODUCE UNIT DEFLECTION. K= P/∆ ∆= PL/AE

Q: PROBLEM O1: A loadP compresses the bronze core, brass, and steel shell as shown in the figure, which…

Q: An aluminum rod 20 mm in diameter and 5 m long is subjected to an axial tensile load of 50 kN…

Q: If an aluminum weighs 165 lb/ft^3, How much will a 12-in dia. sphere weigh when immersed in oil of…

A: Calculate weight of sphere when immerse in oil?

Q: A compound bar consisting of bronze, aluminum, and steel segments is loaded axially as shown in the…

A: Axial Deformation The deformation that occurs in a body due to axial loading is known as axial…

Q: If an aluminum weighs 165 lb/ft^3, How much will a 12-in dia. sphere weigh when immersed in water?…

Q: A brass alloy has a yield strength of 280 MPa, a tensile strength of 390 MPa,and an elastic modulus…

A: Given: Yield strength of brass alloy is 280 MPa. Tensile strength of brass alloy is 390 MPa. Elastic…

Q: The beam in (Figure 1) is constructed from four pieces of wood, glued together as shown. Part A If M…

Q: Question 1: A 25mm diameter aluminum rod is loaded axially in tension with a load of 100kN. The rod…

Q: A compound bar consisting of bronze, aluminum, and steel segments is loaded axially as shown in the…

A: We will draw Free Body Diagram for each section.

Q: A rigid steel container is partially filled with a liquid at 15 atm. The volume of the liquid is…

Q: A rod made of aluminum alloy with a gauge length of 200 mm, diameter of 11mm, and yield strength of…

Q: Q: For the Figure shown below, find the length of bronze. Use the following data: 1. E (steel) = 210…

Q: A rod made of aluminum alloy, with a gauge length of 100 mm, diameter of 10 mm, and yield strength…

A: aWe knowΔL=PLAE0.1=5.851000100π4102EE=74,485Nmm2E=74,485Mpa

Q: axial loads shown in the figure. The cross-sectional area of the steel, bronze, and aluminum are…

Question

Consider a 1 m-long bar of 2024-T81 aluminum alloy with a 20mm-diameter and the following property data:

E=70GPa

Y.S.=410MPa

T.S.=480MPa

%Elongation at failure=8%

What will be the length of the bar under a structural load of 1.2×10^5N in tension? Your answer should be in units of meters (m).

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step 3

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 3 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Similar questions

An aluminum alloy bar with a radius of 7 mm was subjected to tension until fracture and produced results shown in Table P4.3. a. Using a spreadsheet program, plot the stress–strain relationship. b. Calculate the modulus of elasticity of the aluminum alloy. c. Determine the proportional limit. d. What is the maximum load if the stress in the bar is not to exceed the proportional limit? e. Determine the 0.2% offset yield strength. f. Determine the tensile strength. g. Determine the percent of elongation at failure.
) Consider a cylindrical specimen of a steel alloy 10.0 mm in diameter and 75 mm long that is pulled in tension. (a) Determine its elongation when a load of 20,000 N is applied. (b) What is the modulus of elasticity? (c) What is the strength at a strain offset of 0.002? (d) What is the tensile strength?
} 8) A tensile load of 3000 N is applied to a steel bar of cross-sectional area 500 mm?. If a tensile load was applied to an aluminum bar to achieve the same lateral (transvers) strain with the former (steel bar), what would be the load? Note: Original dimensions of the two bars are the same (Est = 2.1 x 105 MPa, Eat = 0.703 × 105 MPa, vg = 0.3, vat = 0.33) E = º , v = - Saterat Eaxial Fatuminum™ 3000 N A-500 mm² A=500 mm² Fatuminum=? 3000 N Steel Aluminum
Consider the 1040 carbon steel listed in the textbook's Table 6.1: A 20mm-diameter bar of this alloy is used as a structural member in an engineering design. The unstressed length of the bar is precisely 1m. The structural load on the bar is 1.2×10^5N in tension. What will be the length of the bar under this structural load (in meters)? Values from table: E [GPa (psi)] = 200(29*10^6) Y.S [MPa (ksi)] = 600(87) T.S [MPa (ksi)] = 750(109) Percent Elongation at failure = 17
3. The distribution of stress in an aluminum machine component is given (in megapascals) by Ox = y + z? Oy = x + z Oz = 3x + y Txy = 3z2 Tyz = x Txz = %3D Calculate the state of strain at a point positioned at (1,2,4). Use E=70 GPa and v = 0.3
SITUATION. As shown in the figure below, a rigid bar with negligible mass is pinned at O and attached to two vertical rods. Assume that the rods were initially stress-free. Allowable stress in steel is 120 MPa and in bronze is 60 MPa. For this problem, a = 1.8m; b = 1.3m; c= 1.7m. a b I Bronze: A 1200 mm E83 GPa Lw2.0m What is the value of P Steel: A 900 mm E 200 GPa L=1.5m
What change in volume would a 100 mm cube of steel suffer at a depth of 5 km in sea water? Take E=2.05 x 10 5N/mm2 and N = 0.82 x 10 5N/mm2
An aluminum alloy cylinder with a diameter of 3 in. and a height of 6 in. is subjected to a compressive load of 50,000 pounds. Assume that the material is within the elastic region and a modulus of elasticity of 11 * 106 psi. a. What will be the lateral strain if Poisson’s ratio is 0.33? b. What will be the diameter after load application? c. What will be the height after load application?
To stretch a 200 mm long tensile test specimen (a) of steel elastically by 0.08 mm. How many loads do I need to apply? (b) What is the maximum length of this sample without plastic deformation? How long can it be extended? (The modulus of elasticity of steel is 210 GPa, yield strength 580 MPa, tensile strength 920 MPa specified as.
The following figure shows the tensile stress-strain curve for a plain-carbon steel. 600 80 500 MPa 600 10 psi 60 80 400 400 60- 300 40 40 200 200 20 20 100 0.005 0.05 0.10 0.15 Strain (a) What is this alloy's tensile strength? MPа (b) What is its modulus of elasticity? GPa (c) What is the yield strength? i MPa Stress (MPa) Stress (10 psi)
1. The following data were obtained during a tension test of an aluminum alloy. The initial diameter of the test specimen was 0.505 in., and the gage length was 2.0 in. Load ( Ib) Elongation (in.) Load ( Ib) Elongation (in.) 14000 0.020 2310 0.0022 14400 0.025 4640 0.0044 14 500 0.060 6950 0.0066 14600 0.080 9290 0.0088 14800 0.100 I1 600 0.0110 14600 0.120 13000 0.01 50 13600 Fracture Plot the stress-strain diagram and determine the following mechanical properties: a. proportional limit þ. modulus of elasticity S. vield stress at 0.2% offset d. ultimate stress e. nominal rupture stress.
The stress-strain diagram for a steel alloy having an original diameter of 0.5 in. and a gage length of 2 in. is given in the figure. If the specimen is loaded until it is stressed to 70 ksi, determine the approximate amount of elastic recovery and the increase in the gage length after it is unloaded. o (ksi) 80 70 60 50 40 30 20 10 e (in./in.) 0 04 0.08 0.12 0.16 0.20 0.24 0.28 0 0005 0.0010.0015 0.002 0.0025 0.0030.0035