Conjugate Beam Method For the beam loaded as shown, by conjugate-beam method (CBM). Determine the slope and deflection at points B and C. EI = Constant. 20kN 30kN A D B 2m 3m 5m 10m

Q: Determine the equation of the influence line for the reaction at A in the continuous beam shown in…

A: By Muller Breslau method, As we have to find the reaction at end A, hence Support at A will be…

Q: x; ]] a» a» dz || X2 a3 a a33

A: For calculation assume,

Q: What is this called?

A: Chisel

Q: Determine the Centroid of 3 Areas.

A:

Q: Sketch SFD and BMD in terms of w and P

A:

Q: Define The required diameter

A: A diameter is a chord that runs through centre point of circle. The centre of circle is at midpoint…

Q: 5. Find diameter y. All dimensions are in millimeters. 1 + 19.30 DIA 118.00 -३०

A: Tapered beam with larger diameter at AB = 19.3 mm  Length of beam ,L = 118 mm  Tapered angle = 3°…

Q: Determine number of external indeterminacy

A: Given data : Number of external support reaction (R)=3+3=6 m=Number of member connected at hinge…

Q: How can I find GH, EG and FH

A:

Q: Quiz #1 Problem 1: Prove the following relationship. Gs Y. (1+ Mc) Y =- 1+e

A:

Q: FIHD THe CENTROID (x $ Y) of THe GazOMETRY

A: Centroid is the point where the mass of whole body acts. If there is a figure which consists of…

Q: 6 in Gin Gin 9 in 3in

A: Schematic diagram of the given problem:

Q: Fo B - P 800 mm C -600 mm

A:

Q: For the given structures, determine the degree of indeterminacy. 8. 8

A: Solution : The number of external reactions ( r ) = 9  The number of members ( n ) = 2  These values…

Q: 7⁄8 inch+  5⁄32 inch

A:

Q: Describe briefly the T-v Diagram.

A: The TV diagram refers to the Temperature-Volume diagram for a particular substance. The diagram…

Q: y 500 50 80 -140- - 140- 80 60 400 500 50 500

A: Given- plate area is given  To find- centroid of given plate area

Q: Give real life examples of Mohr's Circle

A: Brief concept introduction- Mohr's Circle- It gives the relationship between the normal and shear…

Q: 1⁄6 yard +3⁄8 yard

A:

Q: XXXX W₂ W₁ Which of the following most nearly gives the external degree of indeterminacy? 2 4 O 1

A:

Q: According to this figure, What is d? What is dt?

A: Draw the figure.

Q: 3. Name any two-pattern material.

A: Introduction- There are several types of material found in nature. Some materials form certain…

Q: what are the USCS group name for each of the four gradations

A: Given: Specimen LL PL PI Cc Cu 1 53 24 29     2       1.05 95.52 3 27 16 11 3.06 28.34 4…

Q: 05 Find the XT 0.5 1.5 3 2.5

A:

Q: 1) Determine the area of the shape below. -130.0- 100.0 -160.0-

A: The above figure is the trapezoid  The area of the trapezoid = sum of the parallel…

Q: a) top most, hef tmost

A: X = 1.5 cm Y = 5.48 cm

Q: hat about pin d?

A: We know that Forces acting at Joint D are shown in figure below Forces moving away from joints are…

Q: For the following items, answer whether the multiview projection matches the isometric drawing depic…

A: The given figure shows the different items, it is required to state whether the Multiview projection…

Q: 65 degree 6' - 17 degree 54'

A: 1 degree = 60' 65 degree 6' = 64 degree 66'

Q: You are appointed as an officer of Occupational Safety to investigate the incident happened during…

A: Officer of Occupational Safety is responsible for 1) Enforcing safety policies, 2) Conducting audits…

Q: Fullform of  PVDF

A: PVDF: Polyvinyl fluoride.

Q: +y") dx ly

A:

Q: 205, 406 ton=722 %3D How are Yoll tonne - 72 %31

A: Give that, Tonne is metric measure  1 TON  = 0.90718 tonne   TON is American unit