Concentrated loads of Px = 43 kips, Py = 29 kips, and P₂ = 52 kips are applied to the cantilever beam in the locations and directions shown. The beam cross section has dimensions of b = 14 in. and d= 7.0 in. Using a value of a = 7 in., determine the normal and shear stresses at point H. Show these stresses on a stress element. P₂ b 8/10 5 a b 3 Pr a H a a a

Concentrated loads of Px = 43 kips, Py = 29 kips, and P₂ = 52 kips are applied to the cantilever beam in the locations and directions shown. The beam cross section has dimensions of b = 14 in. and d= 7.0 in. Using a value of a = 7 in., determine the normal and shear stresses at point H. Show these stresses on a stress element. P₂ b 8/10 5 a b 3 Pr a H a a a

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter7: Analysis Of Stress And Strain

Section: Chapter Questions

Problem 7.5.3P: The state of stress on an element of material is shown in the figure. Calculate the unit volume...

See similar textbooks

Similar questions

The state of stress on an element of material is shown in the figure. Calculate the unit volume change of the element if the stresses x and y. are -20 ksi and 10 ksi, respectively. Assume E = 10,600 ksi and v = 0.33.
The stresses acting on an element are x= 750 psi, y= 600 psi, and xy = 400 psi. Determine the principal stresses and show them on a sketch of a properly oriented element.
Solve the preceding problem if the norm al and shear stresses acting on the element are sx = 2100 kPa, sy= 300 kPa, and txy= -560 kPa, and the seam is oriented at an angle of 22.5° to the clement.
Determine the maximum tensile and compressive stresses in portion BC of the beam, under loading conditions of two vertical forces that applied on it. The beam has cross section as shown in figure. 100KN | 100KN 200 mm 25 mm 25 mm 150 um 25 mm 1500 mm 500 mm 500 mm 100 mm
800 N 120 N.m d = 8 cm 600 N Q /If the cross section of the femur can be approximated as a circular tube, determine the state of stresses on the 160 N.m points A and B at section due to the loads as shown in figure. T. = 22 mm n = 18 mm tu Sl'o = I
Q 2: A cantilever beam has the profile shown so that it will provide sufficient clearances for large pulleys mounted on the line shaft its supports. The reaction of the line shaft is a load P=115.33KN . Determine the resultant normal stresses at the wall. 160 50 mm 20 120- 09 00%
The wide-flange beam is subjected to the P = 54 kN force. Determine the principal stresses in the beam at point A located on the web at the bottom of the upper flange. Although it is not very accurate, use the shear formula to calculate the shear stress. (Figure 1)
The dimensions of the beam with the cross-section are given as b, a, t as in the figure on the right. The section is under the influence of the eccentric pressure force P. By constructing the equation of the neutral axis for this loading caseCalculate the largest and smallest stresses that will occur in the section and show the normal stress distribution on the section. P kN=85 a (mm)=120 b (mm)=150 t (mm)=40
A simply supported wood beam is subjected to uniformly distributed load q. The width of the beam is 6 in, and the height is 8 in. Determine the normal stress and the shear stress at point C. Show these stresses on a sketch of a stress element at point C.
Find the Principal Stresses on the tube below given the forces in the X,Y and Z axis shown below: Radius: R2=5mm R1=4mm and τxy= 0.1 Pa
3. Listed below is a combination of stresses acting at a point and referred to axes x and y in an elastic material. Using Mohr’s circle of stress determine the principal stresses at the point and their directions for each combination. 1}sigmax -60 n/mm2 , sigmay -36n/mm2 ,TAUxy=5n/mm2 2}}sigmax 30 n/mm2 , sigmay -50n/mm2, TAUxy= 30n/mm2
Calculate non-zero stress components (normal and shear) at points A, B and C. Point C is located at the center of the cross section attached to the wall. Calculate non-zero strain components at point B. Neglect shear stress due to shear force. Given: loading F = 400 N, P-2000 N, and T = 75 N·m, Young's modulus E = 70 GPa, Poisson's ratio v = 0.25 15-mm D. -100 mm