The flanged steel cantilever beam with riveted bracket is subjected to the couple and two forces shown, and their effect on the design of the attachment at A must be determined. Replace the two forces and couple by an equivalent couple M and resultant R at A. The couple is positive if counterclockwise, negative if clockwise. 1.92 KN 0.67 m 1.71 m- 68° A 6 Answers: M = i kN.m R=( i i+ i y I L 460 N.m 10.17 m 10.17 m 1.08 KN j) kN

The flanged steel cantilever beam with riveted bracket is subjected to the couple and two forces shown, and their effect on the design of the attachment at A must be determined. Replace the two forces and couple by an equivalent couple M and resultant R at A. The couple is positive if counterclockwise, negative if clockwise. 1.92 KN 0.67 m 1.71 m- 68° A 6 Answers: M = i kN.m R=( i i+ i y I L 460 N.m 10.17 m 10.17 m 1.08 KN j) kN

Database System Concepts

7th Edition

ISBN:9780078022159

Author:Abraham Silberschatz Professor, Henry F. Korth, S. Sudarshan

Publisher:Abraham Silberschatz Professor, Henry F. Korth, S. Sudarshan

Chapter1: Introduction

Section: Chapter Questions

Problem 1PE

See similar textbooks

Similar questions

Solve the heat flow equation K (aT/ 21 - 0532: at) = (a2T/ax2), where K is PROBLEM %3D the thermal diffusivity of the homogeneous medium. Apply the algorithm to the case of a copper bar of thermal diffusivity of 1.14 cm2/sec with 1 end maintained at 100°C while the other end is held at 0°C. Let the bar be 8 cm long
Questions and Report: 1- Simplify the following functions using Karnaugh map method, and realize it using NAND-NAND circuit. F,(A, B, C, D) = E(0,2,5,7,8,13) +Ed(10,15) F,(W,X,Y,Z) E(5,6,13,14) + Ed(7,15)
The circular rod shown is made of the steel alloy AISI 4140 OQT 900. It has a diameter of 1.00 in and an initial length of 48 in. An axial tensile load of 15 000 lb. is applied during a certain operation. Compute: 1. the equivalent spring constant K, 2. the deformation X of the rod. The Young's modulus of the steel is known to be 30,000,000 psi. F=15 000 lb L= 48 in F=15 000 lb
using (matlabe)
Three balls, with masses of (m;=1 kg, m2=2 kg, m3=3 kg), are fastened to a massless rod of length L=30 cm as shown. The moment of inertia (in kg. m?) about the left end of the rod is: L/2 L/2 Im3 m2 O a. 0.135 O b. 0.015 O c. 0.06 O d. 0.24
Q2. An array of seven LED is used to show the outcome of rolling a die. Design a circuit that illuminates appropriate LEDS to display the outcome of the die. The distribution of the LEDS on the electronic display is given below. a- Derive the Truth Table for the defined function b- Simplify the function using Karnaugh-map c- Express the simplified function F and sketch the circuit c de 1 5 6.
2. Heat conduction in a square plate Three sides of a rectangular plate (@ = 5 m, b = 4 m) are kept at a temperature of 0 C and one side is kept at a temperature C, as shown in the figure. Determine and plot the ; temperature distribution T(x, y) in the plate. The temperature distribution, T(x, y) in the plate can be determined by solving the two-dimensional heat equation. For the given boundary conditions T(x, y) can be expressed analytically by a Fourier series (Erwin Kreyszig, Advanced Engineering Mathematics, John Wiley and Sons, 1993):
Q. No.2 What is the total resistance between point A and ground in below figure for the following conditions? (a) SW1 and SW2 open (c) SW1 open, SW2 closed (b) SW1 closed, SW2 open (d) SW1 and SW2 closed Ao- SWI sW2 sio k 470 k 910 kN
None
A car manufacturing company uses robot to fix screws in the car. The link lengths of the maniputator are 10cm, 20cm and 15cm respectively. They want the three ink parar robots end effect to reach the position of (-10,25) with onentation of 195 degrees Find the joint angles to reach the designated position and orientation.
Logic Function F (x, y, z, w) = ∑ m (0,2,4,6,10,13) + ∑ k (8,12) as sum of minimers are given. (Note: There are terms that are not taken into account.) a. Obtain the Truth Table. b. Simplify with the Karnough Map approach. c. Draw the simplified Logic circuit with two input AND-NOT (NAND) gates. With how many apples you realized, what is your gain? Comment.
A step-index Fiber has a core index of refraction = 1:25. The cut-off angle for light entering the Fiber from air is found to be 8.50º.- (1) What is the numerical aperture of the Fiber? (2) If the Fiber were submersed in water witi same NA, what would be the cut-off angle when nwater = 1.33. (3) Find the power of the Fiber after (2) km, when te power losses is (1.5) dB/km.