Compute the slope and deflection of the simply supported beam shown in figure Q2a. Assume value of E = 29 × 106 psi and I = 22.4 in4.

Q: Consider the beam arrangement with distributed load of 12 kN/m as shown in Figure 1. ii. Determine…

A: Given Data and Initial Calculation :- for ease of calculatation lets take 20kN instead of 12kN.

Q: An I-profile steel beam is supported and loaded as shown in the figure. If the mass of the block is…

A: E=200 GPa,I=17×106 mm4L=8 m or 8000 mmb=2000mmFor simply supported beam, deflection y is given…

Q: Q3. For the beam (E = 4.176×106 ksf) shown below, find the deflection at poin 10K с 2' 16k/ft ДА…

A: For the beam E = 4.176 x 106 ksf

Q: Quiz2 Find the deflection in the point (C) of the beam shown in the figure below. The beam has a…

A: Draw the free-body diagram of beam.

Q: ppose it is specified that the def s own weight should not exceed 0.010 in. per foot of span. a)…

A:

Q: b) The shaft shown in figure 6 supports the three pulley loads. The shaft is made of steel and has a…

A:

Q: Question 4: Use the moment-area method to determine the slope and deflection at point B for the…

A:

Q: Question 2 A beam ABC of length 3m has one support at the left end and the other support at a…

A:

Q: 1. In the figure shown, a variable- area shaft is subjected to the two loads F in each third of its…

A:

Q: The cantilever shown in the figure consists of two structural-steel channels size 3 in., 5.0 lbf/ft.…

A: Given data: wc = 5.0 lbf/ft for 2 channels Assuming, size, d = 3 in Force, F = 145 lbf L = 53 in w =…

Q: 5. A beam of uniform cross section and rectangular is 50mm broad,75mm deep and 6m long. It is simply…

A:

Q: Q2 Find the deflection at the tip of the cantilever shown in figure below. Use EI 20MNm². 1m 30kN/m…

A:

Q: 2 Find the equation of deflection (under the uniformly distributed load) and calculate the maximum…

A:

Q: A wooden beam 5 m long, simply supported at its ends and it is carrying a point load of 8 kN at its…

A: Given data: Length of the beam, L=5 m. Beam is simply supported at it's ends with a concentrated…

Q: 4. A rectangular shapped beam 150mm broad and 300mm deep by 3m long weighs 20kN. and E for the…

A: Given data: b=150 mmh=300 mmL=3 mW=20 kNE=190 GN/m2   It is required to determine the maximum…

Q: / The simply supported beam shown in Figure below has a central half of the beam enlarged, so that…

A:

Q: A simply supported beam -b<y<b, 0 <x<L, as shown below, is subjected to a compressive load of half…

A: σy= -3  4bx δ2Mδx2[y33b2-y] +c3f(x)+c4σy=0 at uy=-bc3f(x)+c4=34 δ2Mσx2 x 23=      σy=-3…

Q: 3P2: A simply supported beam of constant El and length L IS supporting a distributed load omega w…

A:

Q: The simply supported wooden beam shown in Fig. Q4 has a circular cross section with diameter 60 mm…

A:

Q: A simply supported beam shown in figure the beam is 7 m long, 197 mm wide and 591 mm deep with a…

A:

Q: A wooden beam 5 m long, simply supported at its ends and it is carrying a point load of 8 kN at its…

A:

Q: Find the slope deflections using unit load method or any other method in the text book. For the beam…

A:

Q: Analyze the given structure and find out the slope teta at point B of the steel beam .Take E=200 GPa…

A: E=200 GPa = 200*109 Pa I=60 x106 mm4=60*106*10-12m4=60*10-6m4 AB=8m BC=15m W=2kN=2*103 N

Q: Quiz: A straight beam ABCD is rigidly built-in at A and D and carries point loads of 5 kN at B and…

A: A built-in beam, also known as the fixed beam is a type os support in which movement of the beam as…

Q: Q.3. For the frame shown in Fig., find all the required equations to find moments by…

A: To Find : All the equation to determine the moment by slope deflection method. Given : The value of…

Q: A cantiliver of length 20 m is subjected to a point load of 35 kN and a moment of 40 kN m at its…

A: Given data: The length of the cantilever beam is L = 20 m. The point load is F = 35 kN. The moment…

Q: Determine the x and y components of reaction at the pin A. Express your answers using three…

A: Given:F=50 kNFind:Part A: The x and y components of reaction at the pin APart B: The tension in cord…

Q: Q/ For the beam shown in the figure below, find deflection and rotation at point B. EI=12000 kN.m2.…

A:

Q: QUESTION 4 Solve the problem by the moment-area method. The beam has constant flexural rigidity EI.…

A: To find :  The deflection δAand δB at point B and C . Given :  The moment of inertia is I=18.1×106…

Q: 12 kN/m 1 m- -1 m- E=200 GPa 1=4 x 10 mm Figure 1

A:

Q: 05: Derive expressions for the maximum slop and deflection of the cantilever beam shown in Figure…

A:

Q: L 25 mm dia. 5 kN

A: Given,  L = 4 in  d= 0.75 in  P= 499 lb

Q: Problem 9: Find the Slope and deflection at B and C for a cantilever beam of L subjected to a load…

A:

Q: Figure 2 Compute the stiffness matrix D-1 for D in (a) by using Cramer's rule. List the forces…

A:

Q: 9.3-2 A l-meter-long, simply supported copper beam (E = 117 GPa) carries uniformly distributed load…

A: given data; young modulus(E)=117GPa                                 =117*103MPalength of beam(L)=1m…

Q: use EI constant for whole span). A 10-meter-span, propped beam (fixed at the left support and…

A:

Q: Calculate the slope and deflection at the free end of the cantilever bea figure using Method of…

A: For the given slope:

Q: Problem 2: The cantilever beam shown below consists of two structural steel channels, size 3 in x 5…

A: Draw the FBD for the given question. Now write the given values along with suitable variables and…

Q: A= 1200 mm?. Use Strain Energy Method 35 kN - 4m B 84 kN 4m 3m

A:

Q: Consider the beam shown. Suppose that M= 9 kip*ft, P=8 Kip,w=1.4 kip/ft and point D is located just…

A:

Q: A 500 N RAY K ↓ 1<im-31 Im 4m 500 B Re

A:

Q: El

A: To given thatw=7.5kN/m   =7.5N/mmL=12×103mmE=10GPa =10×103MPaI=4×10-5m4 =4×10-5×1012mm4K=800KN/m…

Slope and Deflection

The slope in a deflected beam is described as an angle in radians made by the tangent of the section with the original axis of the beam. The deflection at any point on the axis of the beam is defined as the lateral displacement of the point before and after loading.