Complex Pipeline System_Series Pipes 2. Water flows at a rate of 0.020 cms from reservoir A to reservoir B through three concrete pipes connected in series, as shown in the figure. Determine the difference in the water surface elevations in the reservoirs. Neglect all minor losses. Use Hazen – Williams roughness coefficient C = 120 for all pipes. For the solution, use the Hazen – Williams formula.

Q: a pipe system is as shown er a total head of 100 ft at 40°F. Atmospheric press PSH is 9 ft, will…

A: data  we have  discharge =  495gpm total head = 100 ft  tempertaure = 40°F  Atmospheric pressure…

Q: i the figure below is 2.0 mes the mean vélőčity within the outlet pipe (atmospheric pr 95.48…

A:

Q: A 9.8 m A fluid of relative density 0.88 is flowing through a pipe constant diameter of 15 mm (see…

A: Fluid relative density = 0.88 PA = 150 KPa PB = 225 KPa ZA = 9.8 m ZB = 0 m

Q: A pipeline with roughness ks = 1.0mm and diameter D = 9.6cm connects two reservoirs. The reservoirs…

A: Given: The roughness in the pipe is ks=1.0 mm The diameter of the pipe is d=9.6 cm1 m100 cm=0.096 m…

Q: Galvanized iron pipes with a roughness height of 0.40 cm are used to deliver water from reservoir A…

A:

Q: Water at 68°F flows uphill (B to A) in a 4 inch inside diameter cast iron pipe at a rate of 1.5…

A:

Q: 6 m^3/min of 15.6°C SAE 30 is to be pumped from a tank through 40 meters of horizontal pipe; the oil…

A: Given:Volumetric flow rate of oil, Q=6 m3/min=660m3/s=0.1 m3/sOil temperature, T=15.6oCLength of the…

Q: In the system shown, the water discharge flow rate of 0.0025 m³/s is delivered through the 8 cm…

A: Given data: ◆ The length and diameter of the pipe: L = 406 m , d = 8 cm = 0.08 m ◆ The average…

Q: Q.5 a) In a 80 mm diameter pipeline an oil of specific gravity 0-8 is flowing at the rate of 0-0125…

A: The given values are - D1=0.08m , Specific Gravity S=0.8 , Q=0.125m3sDue to sudden expansion rise in…

Q: The density of the fluid is (1.05x10^3) kg/m3 and the dynamic viscosity is 1.12 x 10 - 3 Ns/m2. The…

A:

Q: Q2/ A fluid containing (water, oil, sand) flowing through the tube and open to the atmosphere as…

A: Start from Pa  going downward is adding pressure and going upward is subtracting pressure.

Q: A tanker carrying tolueneis unloaded to an onshore storage tank using the ship’s pumps. The pipeline…

A:

Q: On a single plot, plot three curves that show the relationship between the pressure generated by the…

A:

Q: [With reference to the Bernoulli and Continuity equations, provide a theoretical analysis of how…

A:

Q: (b) Fluid flow through a horizontal circular pipe of inner radius of 2 cm with centerline velocity…

A: The Reynolds number of the flow is The flow is laminar.

Q: Shown below is an inverted U-tube which is used to drain alcohol from a tank reservoir. The bend of…

A:

Q: I need the answer

A: Consider the pump as a reference line and only minor loss will be taken into account.

Q: The pipe flow in the figure shown below is driven by pressurized air in the tank. What gage pressure…

A:

Q: A pipe of unknown type, length and diameter includes a threaded union (KL = 0.08), 90° %3D threaded…

A: Given data  minor loss coefficients for threaded union = 0.08  minor loss coefficient for 90o…

Q: A fluid is pumped at a rate of 0.00156 m³/s through a 0.025-m-diameter pipe to fill a water tank as…

A:

Q: A (300mm) diameter of pipe, if the discharge (90 L/sec), nozzle diameter (75mm) and pipe length from…

A:

Q: Flow in- de Given at inlet Given at throat section Given at exhaust To = 340K MT МЕх 3 2.2 AEX =…

A: Given:

Q: Water (p = 1000 kg/m³, μ = 1.12 x 10-3 Ns/ m²) flows through a 0.01-m-diameter pipe at a velocity of…

A: Find:The total head losses in the pipe

Q: The water is delivered with piping system given in the figure below. The levation difference between…

A: Given: The difference in elevation Z2 – Z1 = 143.55 m The density of water, ρ = 998 kg/m3 The…

Q: Question 3 Water flows through a 5 cm diameter pipe with a velocity of 4.5 m/s as shown in Figure…

A: “Since you have posted a question with multiple sub-parts, we will provide the solution only to the…

Q: In a fully developed turbulent flow through a pipe, the shear stress is……… Please fill the blank…

A:

Q: Galvanized iron pipes with a roughness height of 0.40 cm are used to deliver water from reservoir A…

A:

Metrology of surface finish

In general terms, the application of scientific principles in the study of measurements is known as metrology. When speaking about measurement, it could be of time, length, microstructures, grain structures, internal crystal discontinuities, surface roughness, measurements of angles, height, width, and so on. While coming to the domain of mechanical engineering, metrology is considered the science of measurements of surface finish, length, surface texture, and angles.