Comment on the following items: a. Why is the material “viscoelastic”? What is meant by this term? b. If more than one material is tested, how did the creep deformation of the different beams differ? Which ones demonstrated the most and least strains? c. Understanding the relationship between instantaneous and delayed elastic response, how does the strain behave at prolonged periods? What do you think would happen after the load is removed?

Comment on the following items: a. Why is the material “viscoelastic”? What is meant by this term? b. If more than one material is tested, how did the creep deformation of the different beams differ? Which ones demonstrated the most and least strains? c. Understanding the relationship between instantaneous and delayed elastic response, how does the strain behave at prolonged periods? What do you think would happen after the load is removed?

Materials Science And Engineering Properties

1st Edition

ISBN:9781111988609

Author:Charles Gilmore

Publisher:Charles Gilmore

Chapter6: Introduction To Mechanical Properties

Section: Chapter Questions

Problem 6.2P

See similar textbooks

Similar questions

A bronze rod is rigidly attached between an aluminum rod and a steel rod as shown in the figure below. Axial loads are applied at the positions indicated. a) Find the maximum value of P that will not exceed a stress in steel of 140 MPa, in bronze of 100 MPa, or in aluminum of 90 MPa. b) Determine the deformation of the bronze rod if the value of P is 22.50 KN. The moduli of elasticity are 200 GPa for steel, 80 GPa for bronze and 70 GPa for aluminum.
A steel alloy specimen having a rectangular cross section of dimensions 19.1 mm x 3.1 mm (0.7520 in. × 0.1220 in.) has the stress-strain behavior shown in the Animated Figure 6.22b. If this specimen is subjected to a tensile force of 98290 N (22100 Ib;) then (a) Determine the amount of elastic strain induced. (b) Determine the amount of plastic strain induced. (c) If its original length is 610 mm, what will be its final length after this force is applied and then released? The elastic modulus for steel is 207 GPa. (a) i (b) i (c) i mm
PROBLEM 1 A steel rod with a cross sectional area of 150 mm? is stretched between two fixed points. The tensile load at 20°C is 5000 N. a.) What will be the stress at -20°C? b.) At what temperature will the stress be zero? Assume a = 11 .7 µm/m°C, and E = 200 Gpa *Show geometry of deformation ©sidewar
Discuss the principles of stress and deformation analysis for several kinds of stresses
Homework #6 Problem 1. A steel alloy core is bonded firmly to the copper tube to form the shaft shown. The materials have the shear stress-strain diagrams are shown in the figure. a) If the total applied torque is 15 kN.m, determine the torque resisted by the core and tube. b) What is the maximum elastic torque that can be applied to the shaft? What is the corresponding maximum shear strain in the shaft? c) What is the maximum torque that one can apply to the shaft? 100 m 60 mm +(MPa) 180 450 mm 15 KN-m 0.0024 (MPa) Steel Alloy 36 0.002 Copper Alloy (rad) y (rad)
A specimen of steel has a rectangular cross section 20 mm wide and 40 mm thick, an elastic modulus of 207 GPa, and a Poisson's ratio of 0.30. If this specimen is pulled in tension with a force of 60,000 N, what is the change in width if deformation is totally elastic? O Increase in width of 3.62 x 10-6 m O Decrease in width of 7.24 x 10-6 m Increase in width of 7.24 x 106 m O Decrease in width of 2.18 x 10-6 m
Find the poisson's ratio for a given material if the modulus of elasticity is 100 GN/m2 and it's modulus of elasticity in shear is 40 GPa.
2. A steel bar, whose cross section is 0.55 inch by 4.05 inches, was tested in tension. An axial load of P = 30,500 lb. produced a deformation of 0.105 inch over a gauge length of 2.05 inches and a decrease of 0.0075 inch in the 0.55-inch thickness of the bar. Determine the lateral strain. * Your answer Determine the axial strain. Your answer Determine the Poisson's ratio v. * Your answer Determine the decrease in the 4.05-in. cross-sectional dimension (in inches). * Your answer
Erase Figure 9 In using the method of consistent deformation in analysing structures, the compatibility equation has to be written. Why is this necessary?
Prove that Young's modulus of a wire is equal to the stress necessary to double its length.
) Consider a cylindrical specimen of a steel alloy 10.0 mm in diameter and 75 mm long that is pulled in tension. (a) Determine its elongation when a load of 20,000 N is applied. (b) What is the modulus of elasticity? (c) What is the strength at a strain offset of 0.002? (d) What is the tensile strength?
Problem 11. [Concepts: Calculating stress from internal forces, nonlinear stress-strain response, elongation from strain.] Acetal plastic has a stress-strain diagram as shown. a) Determine the yield strength assuming a 0.2% offset. b) If a bar of this material has a length of 3 ft and cross-sectional area of 0.875 in², and is subjected to an axial load of 2.5 kip, determine its elongation. c) Determine the modulus of toughness just before it fractures if failure occurs at a = 0.12. σ (psi) a = 9.5(10³) €¹/3 € (in./in.)