Cold Circular saws are capable of making cuts accurate to what tolerance?

Q: 11. Two cutting tools with tool life equations given below are being compared: Tool 1: VTº-1-150…

A:

Q: How is the tool geometry of single point cutting tool designated or specified in ASA, ORS and NRS…

A: GIVEN DATA - TOOL DESIGNATION SYSTEM GIVEN WE HAVE TO EXPLAIN IT

Q: What is the tool length offset? How is the tool length offset measured

A:

Q: Describe four (4) functions of cutting fluid.

A: Dear student, we are suppose to solve only one question. Please post other question as a separate…

Q: In a multi point cutting tool the positive rake angle is used to cut low tensile strength and…

A:

Q: Differentiate the Branch and Bound Method and Gomory's Cutting Plane Method.

A: given; Differentiate the Branch and Bound Method and Gomory's Cutting Plane Method.

Q: For pocket operation of 2 x 3 inch surface and dept of 0.06 in using 0.5 in end mill tool. What is…

A:

Q: Which formula is used for calculation of specific cutting pressure?

A:

Q: The angle on a single-point cutting tool geometry in which the face of a tool is inclined sideways…

A: Back rake angle: It is the inclination of the face toward or away from the end or the end cutting…

Q: 3. Describe the characteristic of good cutting tools

A: Good cutting tool must have the following characteristics:- Good strength High thermal stability…

Q: how would i do the Chamfering for this part on the lathe? what cutting tool would i use  what…

A: Given drawing:

Q: 1. Differentiate conventional and non-conventional cutting tools

A: Based on type of toop used, machining tool can be categorized into two groups, conventional and…

Q: Ql:- Put a mark of True or false for below:- (a):- The milling cutting tool has a single cutting…

A: As per bartleby guidelines we are allowed to solve only 1st 3 subparts if multiple subparts are…

Q: Which of the following best describes the "cutting plane" of aligned sectional view: It is a…

A: it is a combination of parallel cutting planes

Q: In a multi point cutting tool the negative rake angle is used for high tensile strength materials.…

A: Positive rake angle used for ductile or soft material while negative rake angle used for higher…

Q: Blind hole 20 mm diameter, 60 mm deep are being drilled in steel stock, drilling spindle speed is…

A:

Q: How twist drill works?

A: Drilling machine or drill is commonly used to make hole. This is applied in the finishing operation…

Q: shaper cutting tool

A:

Q: Question 3. State whether or not the following statements are true, explaining your reaso 3.a. For…

A: (a) The given statement is true . To exhibit that for a comparative shear point, there are two rake…

Q: What is the approximate % change in the life, t, of the tool with zero rake angle used in orthogonal…

A: Given: Flank wear∝cot α

Q: an a thick saw blade be used as a broach. Why. Why is it difficult to make

A: As per the guidelines we are subjected to solve only one question at a time. Please repost the same…

Q: This troubleshooting probably occurs in the drilling operation due to high cutting speed,…

A: Option (d) is correct. Excessive drill wear

Q: What is the cutting speed in fpm of a

A:

Q: Which of the following statements about cutting variables for finishing cuts is true? Finishing cuts…

A: Solution:

Q: A drill bit must not over travel during hole boring, what you should do?

A: Boring operation is defined as the operation in which an enlargement of the diameter of the hole…

Q: Define the fundamental of cutting.

A: Definition of Cutting : Cutting is defined as It's process which creates new surfaces in a solid by…

Q: The advantage of an independent chuck is that it is easy to work with. Select one: True False

A: A chuck is a machine component that is used to hold the workpiece in the predefined position in such…

Q: What is the cutting speed? when main axis spindle speed is 700rpm, and external diameter is 15mm ?

A: Given:-N=700 rpmD=15mmTo find:-Cutting speed, Vc

Q: When sharpening layout tools and other tools, what is the most important consideration?

A: During the sharpening layout tools or other tools, there are few terms which are most important…

Q: In a multi point cutting tool the positive rake angle is used to cut low tensile strength and…

A: This question is from manufacturing engineering subject.

Q: A single point cutting tool designated as follows 8-14-6-6-6-20-1 is used to machine a work with…

A:

Q: Identify the true statement from the following a. Unit of cutting speed in millimetre per minute b.…

A: There are various terms related to the machining operations, such as cutting speed, feed rate, depth…

Q: QUESTION 12 How long would it take a turn 6 inches of 1-inch bar stock on a No. 3W. and S. turret…

A: This is the very basic question of machining time calculation on lathe.

Q: A straight turning operation is carried out using a single point cutting tool on an AISI 1020 steel…

A: Given data: The feed rate is f = 0.2 mm/rev. The depth of cut is d = 0.5 mm. The side cutting edge…

Q: Excessive temperature at the cutting tool point will lead to the following: Brittle fracture ، All…

A: Excessive temperature at the cutting tool point is very dangerous.

Q: What type of saw consists of a continuous band of metal with cutting teeth on one edge?

A: Given Saw consists of a continuous band of metal with cutting teeth on one edge To find Identify the…

Q: What part of the lathe is used to set the feed rate of the cutting tool?

A: Part of the lathe is used to set the feed rate of the cutting tool is Quick Change Gear Box Quick…

Q: What do you mean by attrition wear in tools?

A: The attrition wear in tools is a kind of adhesive wear. The strong bond between the chip and tool…

Q: Increasing the entering angle of the tool affects the vibrations during cutting by:

A: Entering angle is the angle between the leading cutting edge of the tool and surface of the…

Q: Q3:- Choose the Correct answer. (1):- The drilling tool must be with a- High hardness b- Low…

A:

Q: How nuch machlning time required a mild steel rod trom 65mm 58 mm over a length of 100 mm by turning…

A: Given Data ⇒ Initial Diameter of mild steel rod (D)=65 mm Length(L)=100 mm Approach Length(A)=5 mm…

Machining Processes and Machine Tools

Machining is represented as the process in which an excessive amount of substance is eliminated from the particular element in the form of pieces. In machining, cutting tools such as rotary tools, lathe, drill press, grinder, chop saw, welders, and many more are applied to get the desired shape. As compared to other manufacturing processes, machining is precise and versatile.