Choose the correct statement for Dual converter (a) Rectifier Il produces 2 nd Quadrant parameters (b) Rectifier Il produces 3 rd Quadrant parameters (c) Rectifier I produces 4 th Quadrant parameters (d) Rectifier I produces 1 st Quadrant parameters O i. all the above O ii. (c) and (b) only O i. (b) and (d) only O iv. (a) and (b) only A 3 phase fully controlled rectifier has a 3 phase line to line supply voltage of 410 V rms at 50 Hz for 14 ohm and 1.5 H load. If the firing angle a = 50, then the average output voltage is, .v.

Choose the correct statement for Dual converter (a) Rectifier Il produces 2 nd Quadrant parameters (b) Rectifier Il produces 3 rd Quadrant parameters (c) Rectifier I produces 4 th Quadrant parameters (d) Rectifier I produces 1 st Quadrant parameters O i. all the above O ii. (c) and (b) only O i. (b) and (d) only O iv. (a) and (b) only A 3 phase fully controlled rectifier has a 3 phase line to line supply voltage of 410 V rms at 50 Hz for 14 ohm and 1.5 H load. If the firing angle a = 50, then the average output voltage is, .v.

Electricity for Refrigeration, Heating, and Air Conditioning (MindTap Course List)

10th Edition

ISBN:9781337399128

Author:Russell E. Smith

Publisher:Russell E. Smith

Chapter12: Electronic Control Devices

Section: Chapter Questions

Problem 4RQ: What is the difference between a diode and rectifier?

See similar textbooks

Similar questions

Comparing the performance with controlled rectifier circuit which one of the following statement is correct for DC -DC chopper ? O a. Regenerative braking process is very slow O b. Efficiency is poor in chopper circuit O c. small filters are required O d. Switching frequency is not responsible for output ripples
Choose the wrong statement for Dual converter (a) Rectifier II produces 2 nd Quadrant parameters(b) Rectifier II produces 1 st Quadrant parameters(c) Rectifier I produces 4 th Quadrant parameters(d) Rectifier I produces 2 nd Quadrant parameters a. (b) and (d) b. (c) and (b) c. (a) and (c) d. (a) and (b)
Single phase half sinusoidal wave controlled rectifier with (? = 30?) pure resistive load (Vs =220 v. f=60 Hz, R=10Ω) Determine the average output voltage Vo  Determine the r.m.s value of the output voltage
Comparing the performance with controlled rectifier circuit which one of the following statement is wrong for DC -DC chopper ? a. small filters are required O b. Regenerative braking process is very slow O c. Switching frequency is responsible for output ripples O d. Efficiency is better in chopper circuit
By comparing the performance of DC -DC chopper with controlled rectifier circuit which one of the following statement is wrong ? O a. Efficiency is better in chopper circuit b. small filters are required in chopper circuit O c. Regenerative braking process is very slow in chopper circuit O d. Switching frequency is responsible for output ripples in chopper circuit Clear my choice
-,- three phase half wave controlled rectifier with resistive load (R=10 2) if the input supply voltage is (Vrms = 380 Volt and f= 50 Hz) and the trigger angle (a = 60°), then determine the followings:- a) Draw the rectifier circuit. b) Draw to scale the input voltage, the load voltage and the current waveforins. c) Calculate the average value of the output voltage.
State whether the following statements are TRUE or FALSE (Q1---Q3): The DC output voltage of a Full wave bridge Rectifier is less than the DC output voltage of a half wave rectifier for the same input. 1 In Full Wave Center Tapped Rectifier, Peak Inverse Voltage is triple of the input 2 voltage. 3 In forward biased, the voltage drop across Germanium diode is 0.3 volt.
For a half wave or full wave rectifier the Peak Inverse Voltage of the rectifier is alwaysa) Greater than the input voltageb) Smaller than the input voltagec) Equal to the input voltaged) Greater than the input voltage for full wave rectifier and smaller for the half wave rectifier Bridge rectifier is an alternative fora) Full wave rectifierb) Peak rectifierc) Half wave rectifierd) None of the mentioned In a half wave rectifier, the sine wave input is 200sin300t. The average value of output voltage is?a) 57.876V c) 67.453Vb) 63.694V d) 76.987V If the input frequency of a half wave rectifier is 100Hz, then the ripple frequency will be_________a) 150Hz c) 200Hzb) 100Hz d) 300Hz In a center-tapped full wave rectifier, the input sine wave is 250sin100t. The output ripple frequency will be _________a) 50Hz c) 100Hzb) 25Hz d) 200Hz Ripple factor of bridge full wave rectifier is?a) 1.414 c) 1.212b) 0.482 d) 1.321
FULL WAVE RECTIFIER CIRCUIT: Explain what happens to the “output” LED (i.e. the LED marked “vo”) as the frequency is increased from low frequency (1 Hz) to higher frequencies (closer to the main supply frequency of 50 Hz)
Draw the waveform Vs , VL, ID ((each)) , is for single phase full wave rectifier with RL load for the following firing angle a) 0° b)45° c)90° d)135° f)180°
In a full-wave rectifier _______________. a) the output is apure DC voltage. b) only the negative half of the input cycle is used. c) only the positive half of the input used. d) the complee input cycle is used.
6. The purpose of zero detecting circuit in controlled rectifiers is: * To measure the amplitude of input signal . To measure the phase shift of input signal. To measure the reference time of firing pulse. To measure the frequency of input signal.